| Age | Commit message (Collapse) | Author |
|---|
|
Options which deal with memory locations and have a default value of 0x0
are dangerous, as that is often not a valid memory location. Rework
SPL_LOAD_FIT_ADDRESS as follows:
- Add SPL_HAS_LOAD_FIT_ADDRESS to guard prompting the question as the
case of loading a FIT image does not strictly require setting an
address and allows for a malloc()'d area to be used.
- For SPL_RAM_SUPPORT, select the new guard symbol if SPL_LOAD_FIT is
enabled because in that case an address must be provided.
- Update defconfigs for these new changes. Largely this means some
defconfigs need to enable SPL_HAS_LOAD_FIT_ADDRESS to maintain their
current status. In the case of sandbox, we also need to set
SPL_LOAD_FIT_ADDRESS to 0x0.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Hawk board
The redundant environment offset is already set in board configuration,
but the redundant environment itself is not explicitly enabled. Make
sure the redundant environment is enabled, as we most certainly do want
to have two copies of the environment.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
|
|
Sparrow Hawk board
Avoid use of hard-coded address in boot command, instead use $loadaddr
which is the default load address. This improves consistency of the
environment on this board.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
|
|
board
Enable support for PCIe based xHCI USB 3.0 driver and USB mass
storage support on Retronix R-Car V4H Sparrow Hawk board .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
|
|
V4H Sparrow Hawk board
Enable support for Winbond SPI NOR on Retronix R-Car V4H Sparrow Hawk board,
this is required to support W77Q51NW on new board revision EVTB1 operational.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
|
|
dw_pcie_link_set_max_link_width()"
This patch set from Marek Vasut <marek.vasut+renesas@mailbox.org>
introduces dw_pcie_link_set_max_link_width() similar to the Linux Kernel
and then migrates the current platform drivers to use it. Next it adds
support for Renesas R-Car Gen4 platforms and enables it on one.
Link: https://lore.kernel.org/r/20250617081641.8385-1-marek.vasut+renesas@mailbox.org
|
|
Sparrow Hawk board
Enable support for R-Car Gen4 PCIe controller and NVMe storage
on Retronix R-Car V4H Sparrow Hawk board .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
|
|
The CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0xeb300000 does not make it into
board .config on either R-Car V4H White Hawk or Sparrow Hawk, remove
this configuration option. The early SPL stack is however pointing
into the RT-VRAM and may corrupt payload loaded into the RT-VRAM by
the BootROM. Set the early SPL stack at fixed location at the end of
System RAM instead, where it cannot interfere with the payload loaded
into RT-VRAM.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
|
|
Add Retronix R-Car V4H Sparrow Hawk board based on Renesas R-Car V4H ES3.0
(R8A779G3) SoC. This is a single-board computer with single gigabit ethernet,
DSI-to-eDP bridge, DSI and two CSI2 interfaces, audio codec, two CANFD ports,
micro SD card slot, USB PD supply, USB 3.0 ports, M.2 Key-M slot for NVMe SSD,
debug UART and JTAG.
DT is imported from Linux next commit:
a719915e76f2 ("arm64: dts: renesas: r8a779g3: Add Retronix R-Car V4H Sparrow Hawk board support")
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
|
