| Age | Commit message (Collapse) | Author |
|---|
|
Introduce a new version of the Keystone-II "ddr" command for testing the
inline ECC support in the DDRSS bridge available on K3 devices. The ECC
hardware support in K3's DDRSS and the test method differ substantially
from what we support in the K2 variant of the command. This K3 DDRSS
command currently supports only single controller testing.
The ECC error injection procedure follows these steps:
1) Flush and disable the data cache.
2) Disable the protected ECC Rx range.
3) Flip a bit in the address.
4) Restore the range to original.
5) Read the modified value (corrected).
6) Re-enable the data cache.
This will cause the 1-bit ECC error count to increase while the read
will return the corrected value.
The K3 version of the command extends the syntax for the "ecc_err"
argument by also introducing an argument for range which specifies which
range (0, 1, 2) the address is located in.
Multi-bit ECC errors are uncorrectable and will lead to a synchronous
abort.
Signed-off-by: Georgi Vlaev <g-vlaev@ti.com>
Signed-off-by: Santhosh Kumar K <s-k6@ti.com>
[n-francis@ti.com: Add J7 and multiple-region support, simplify logic]
Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
Reviewed-by: Udit Kumar <u-kumar1@ti.com>
|
|
As part of bringing the master branch back in to next, we need to allow
for all of these changes to exist here.
Reported-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
When bringing in the series 'arm: dts: am62-beagleplay: Fix Beagleplay
Ethernet"' I failed to notice that b4 noticed it was based on next and
so took that as the base commit and merged that part of next to master.
This reverts commit c8ffd1356d42223cbb8c86280a083cc3c93e6426, reversing
changes made to 2ee6f3a5f7550de3599faef9704e166e5dcace35.
Reported-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Remove <common.h> from all "cmd/" files and when needed add
missing include files directly.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Replace instances of http://www.ti.com with https://www.ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
|
|
- Add some dependencies to CMD_DDR3 as this is only valid on some
platforms (which tend to select it as well).
- The proper gate for going in to cmd/ti is not
CONFIG_TI_COMMON_CMD_OPTIONS as nothing under there is controlled by
that symbol but the general TI architecture options.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
- Generally we just drop the #ifdef CONFIG_SYS_LONGHELP and endif lines
and use U_BOOT_LONGHELP to declare the same variable name as before
- In a few places, either rename the variable to follow convention or
introduce the variable as it was being done inline before.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
This converts 5 usages of this option to the non-SPL form, since there is
no SPL_SYS_LONGHELP defined in Kconfig
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
The rest of the unmigrated CONFIG symbols in the CONFIG_SYS_SDRAM
namespace do not easily transition to Kconfig. In many cases they likely
should come from the device tree instead. Move these out of CONFIG
namespace and in to CFG namespace.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Just a spelling mistake.
Signed-off-by: Ramin Zaghi <rzaghi@visualSilicon.com>
|
|
It is a pain to have to specify the value 10 in each call. Add a new
dectoul() function and update the code to use it.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
It is a pain to have to specify the value 16 in each call. Add a new
hextoul() function and update the code to use it.
Add a proper comment to simple_strtoul() while we are here.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Add support command for debugging K3 power domains. This is useful with
the HSM rearch setup, where power domains are directly controlled by SPL
instead of going through the TI SCI layer. The debugging support is only
available in the u-boot codebase though, so the raw register access
power domain layer must be enabled on u-boot side for this to work. By
default, u-boot side uses the TI SCI layer, and R5 SPL only uses the
direct access methods.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tero Kristo <kristo@kernel.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
|
|
Move this out of the common header and include it only where needed. In
a number of cases this requires adding "struct udevice;" to avoid adding
another large header or in other cases replacing / adding missing header
files that had been pulled in, very indirectly. Finally, we have a few
cases where we did not need to include <asm/global_data.h> at all, so
remove that include.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Move this header out of the common header.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
We should not use typedefs in U-Boot. They cannot be used as forward
declarations which means that header files must include the full header to
access them.
Drop the typedef and rename the struct to remove the _s suffix which is
now not useful.
This requires quite a few header-file additions.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
These functions relate to memory init so move them into the init
header.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
These functions belong in cpu_func.h. Another option would be cache.h
but that code uses driver model and we have not moved these cache
functions to use driver model. Since they are CPU-related it seems
reasonable to put them here.
Move them over.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
If the ECC is enabled over the entire memory region, we need to ensure
the printf/put calls do not modify the stack after ECC is disabled.
Moved the printf/put statements after ECC is enabled.
Signed-off-by: Krunal Bhargav <k-bhargav@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
|
ecc_address_range registers contains the start address and end address
of the DDR address space. But the ddr cmd driver is assuming the register
contains the start address and size of the DDR address space. Because
of this some valid ecc addresses are errored out as invalid address.
Fix this calculation.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
|
When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from. So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry. Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.
In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.
This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents. There's also a few places where I found we did not have a tag
and have introduced one.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Keystone and DRA7 based TI platforms uses same
EMIF memory controller. cmd_ddr3 command is customized
for keystone platforms, make it generic so that it can
be re used for DRA7 platforms.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
|
Move cmd_ddr3 to cmd/ti in order to make
it build for non-keystone TI platforms.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
[trini: Rename to ddr3.c not cmd_ddr3.c]
Signed-off-by: Tom Rini <trini@konsulko.com>
|
