| Age | Commit message (Collapse) | Author |
|---|
|
U-Blox M8/M9 chip have a pin to start it in safeboot mode, to be used
to recover from situations where the flash content has become
corrupted and needs to be restored. If this pin is asserted at power
up/reset, the receiver starts in safeboot mode and GNSS operation is
disabled.
Deassert the safeboot pin when probing this driver.
Signed-off-by: Alejandro Enrique <alejandroe1@geotab.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20250911-ubx-safeboot-v3-2-32fe6b882a3c@geotab.com
[ johan: deassert after requesting supplies ]
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
The Renesas KingFisher board includes a U-Blox Neo-M8 chip. This chip
has a reset pin which is also wired on the board. When Linux starts,
reset is asserted by the firmware. Deassert the reset pin when probing
this driver.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
[ johan: rename gpio descriptor variable ]
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
v_bckp shall always be enabled as long as the device exists. We now have
a regulator helper for that, use it.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
Drop semicolons after function definitions that have managed to sneak in
and get reproduced.
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
Add compatible for u-blox NEO-6M GPS module.
Signed-off-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
The structure ubx_gserial_ops is local to the source and does not need
to be in global scope, so make it static.
Cleans up sparse warning:
symbol 'ubx_gserial_ops' was not declared. Should it be static?
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add a "type" device attribute and a "GNSS_TYPE" uevent variable which
can be used to determine the type of a GNSS receiver. The currently
identified types reflect the protocol(s) supported by a receiver:
"NMEA" NMEA 0183
"SiRF" SiRF Binary
"UBX" UBX
Note that both SiRF and UBX type receivers typically support a subset of
NMEA 0183 with vendor extensions (e.g. to allow switching to the vendor
protocol).
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add driver for serial-connected u-blox GNSS receivers.
Note that the driver uses the generic GNSS serial implementation and
therefore essentially only manages power abstracted into three power
states: ACTIVE, STANDBY, and OFF.
For u-blox receivers with a main supply and no enable-gpios, this simply
means that the main supply is disabled in STANDBY and OFF (the optional
backup supply is kept enabled while the driver is bound).
Note that timepulse-support is not yet implemented.
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
