From d64aab0c6fdc67113f2332a295d244b53bf694d6 Mon Sep 17 00:00:00 2001 From: Oliver Neukum Date: Wed, 20 Apr 2016 16:28:09 +0200 Subject: hub: admit devices are SS+ If a port can do 10 Gb/s the kernel should say so. The corresponding check needs to be added. Signed-off.by: Oliver Neukum > Signed-off-by: Greg Kroah-Hartman --- drivers/usb/core/hub.c | 2 ++ 1 file changed, 2 insertions(+) (limited to 'drivers/usb/core') diff --git a/drivers/usb/core/hub.c b/drivers/usb/core/hub.c index 38cc4bae0a82..c2270d8fac12 100644 --- a/drivers/usb/core/hub.c +++ b/drivers/usb/core/hub.c @@ -104,6 +104,8 @@ static int usb_reset_and_verify_device(struct usb_device *udev); static inline char *portspeed(struct usb_hub *hub, int portstatus) { + if (hub_is_superspeedplus(hub->hdev)) + return "10.0 Gb/s"; if (hub_is_superspeed(hub->hdev)) return "5.0 Gb/s"; if (portstatus & USB_PORT_STAT_HIGH_SPEED) -- cgit v1.2.3 From 98b74b0ee57af1bcb6e8b2e76e707a71c5ef8ec9 Mon Sep 17 00:00:00 2001 From: David Mosberger Date: Tue, 8 Mar 2016 14:42:48 -0700 Subject: drivers: usb: core: Don't disable irqs in usb_sg_wait() during URB submit. usb_submit_urb() may take quite long to execute. For example, a single sg list may have 30 or more entries, possibly leading to that many calls to DMA-map pages. This can cause interrupt latency of several hundred micro-seconds. Avoid the problem by releasing the io->lock spinlock and re-enabling interrupts before calling usb_submit_urb(). This opens races with usb_sg_cancel() and sg_complete(). Handle those races by using usb_block_urb() to stop URBs from being submitted after usb_sg_cancel() or sg_complete() with error. Note that usb_unlink_urb() is guaranteed to return -ENODEV if !io->urbs[i]->dev and since the -ENODEV case is already handled, we don't have to check for !io->urbs[i]->dev explicitly. Before this change, reading 512MB from an ext3 filesystem on a USB memory stick showed a throughput of 12 MB/s with about 500 missed deadlines. With this change, reading the same file gave the same throughput but only one or two missed deadlines. Signed-off-by: David Mosberger Signed-off-by: Greg Kroah-Hartman --- drivers/usb/core/message.c | 15 +++++++-------- 1 file changed, 7 insertions(+), 8 deletions(-) (limited to 'drivers/usb/core') diff --git a/drivers/usb/core/message.c b/drivers/usb/core/message.c index 8e641b5893ed..e13a2e557715 100644 --- a/drivers/usb/core/message.c +++ b/drivers/usb/core/message.c @@ -302,9 +302,10 @@ static void sg_complete(struct urb *urb) */ spin_unlock(&io->lock); for (i = 0, found = 0; i < io->entries; i++) { - if (!io->urbs[i] || !io->urbs[i]->dev) + if (!io->urbs[i]) continue; if (found) { + usb_block_urb(io->urbs[i]); retval = usb_unlink_urb(io->urbs[i]); if (retval != -EINPROGRESS && retval != -ENODEV && @@ -515,12 +516,10 @@ void usb_sg_wait(struct usb_sg_request *io) int retval; io->urbs[i]->dev = io->dev; - retval = usb_submit_urb(io->urbs[i], GFP_ATOMIC); - - /* after we submit, let completions or cancellations fire; - * we handshake using io->status. - */ spin_unlock_irq(&io->lock); + + retval = usb_submit_urb(io->urbs[i], GFP_NOIO); + switch (retval) { /* maybe we retrying will recover */ case -ENXIO: /* hc didn't queue this one */ @@ -590,8 +589,8 @@ void usb_sg_cancel(struct usb_sg_request *io) for (i = 0; i < io->entries; i++) { int retval; - if (!io->urbs[i]->dev) - continue; + usb_block_urb(io->urbs[i]); + retval = usb_unlink_urb(io->urbs[i]); if (retval != -EINPROGRESS && retval != -ENODEV -- cgit v1.2.3 From 5f2e5fb873e269fcb806165715d237f0de4ecf1d Mon Sep 17 00:00:00 2001 From: David Mosberger Date: Tue, 8 Mar 2016 14:42:49 -0700 Subject: drivers: usb: core: Minimize irq disabling in usb_sg_cancel() Restructure usb_sg_cancel() so we don't have to disable interrupts while cancelling the URBs. Suggested-by: Alan Stern Signed-off-by: David Mosberger Signed-off-by: Greg Kroah-Hartman --- drivers/usb/core/message.c | 37 +++++++++++++++++-------------------- 1 file changed, 17 insertions(+), 20 deletions(-) (limited to 'drivers/usb/core') diff --git a/drivers/usb/core/message.c b/drivers/usb/core/message.c index e13a2e557715..ea681f157368 100644 --- a/drivers/usb/core/message.c +++ b/drivers/usb/core/message.c @@ -577,31 +577,28 @@ EXPORT_SYMBOL_GPL(usb_sg_wait); void usb_sg_cancel(struct usb_sg_request *io) { unsigned long flags; + int i, retval; spin_lock_irqsave(&io->lock, flags); + if (io->status) { + spin_unlock_irqrestore(&io->lock, flags); + return; + } + /* shut everything down */ + io->status = -ECONNRESET; + spin_unlock_irqrestore(&io->lock, flags); - /* shut everything down, if it didn't already */ - if (!io->status) { - int i; + for (i = io->entries - 1; i >= 0; --i) { + usb_block_urb(io->urbs[i]); - io->status = -ECONNRESET; - spin_unlock(&io->lock); - for (i = 0; i < io->entries; i++) { - int retval; - - usb_block_urb(io->urbs[i]); - - retval = usb_unlink_urb(io->urbs[i]); - if (retval != -EINPROGRESS - && retval != -ENODEV - && retval != -EBUSY - && retval != -EIDRM) - dev_warn(&io->dev->dev, "%s, unlink --> %d\n", - __func__, retval); - } - spin_lock(&io->lock); + retval = usb_unlink_urb(io->urbs[i]); + if (retval != -EINPROGRESS + && retval != -ENODEV + && retval != -EBUSY + && retval != -EIDRM) + dev_warn(&io->dev->dev, "%s, unlink --> %d\n", + __func__, retval); } - spin_unlock_irqrestore(&io->lock, flags); } EXPORT_SYMBOL_GPL(usb_sg_cancel); -- cgit v1.2.3 From f5e6253fe6de35fc2fa059974dbd9d61f32e4cd0 Mon Sep 17 00:00:00 2001 From: Chunfeng Yun Date: Thu, 28 Apr 2016 11:42:20 +0800 Subject: usb: core: buffer: avoid NULL pointer dereferrence NULL pointer dereferrence will happen when class driver wants to allocate zero length buffer and pool_max[0] can't be used, so simply returns NULL in the case. Signed-off-by: Chunfeng Yun Signed-off-by: Greg Kroah-Hartman --- drivers/usb/core/buffer.c | 3 +++ 1 file changed, 3 insertions(+) (limited to 'drivers/usb/core') diff --git a/drivers/usb/core/buffer.c b/drivers/usb/core/buffer.c index 2741566ee4f2..98e39f91723a 100644 --- a/drivers/usb/core/buffer.c +++ b/drivers/usb/core/buffer.c @@ -122,6 +122,9 @@ void *hcd_buffer_alloc( struct usb_hcd *hcd = bus_to_hcd(bus); int i; + if (size == 0) + return NULL; + /* some USB hosts just use PIO */ if (!IS_ENABLED(CONFIG_HAS_DMA) || (!bus->controller->dma_mask && -- cgit v1.2.3 From 10871c13608a624562e082196148f1dc4e37005e Mon Sep 17 00:00:00 2001 From: Michele Curti Date: Wed, 27 Apr 2016 21:23:07 +0200 Subject: usb: devio: declare usbdev_vm_ops as static usbdev_vm_ops is used in devio.c only, so declare it as static Signed-off-by: Michele Curti Signed-off-by: Greg Kroah-Hartman --- drivers/usb/core/devio.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers/usb/core') diff --git a/drivers/usb/core/devio.c b/drivers/usb/core/devio.c index 52c4461dfccd..73ce87166401 100644 --- a/drivers/usb/core/devio.c +++ b/drivers/usb/core/devio.c @@ -216,7 +216,7 @@ static void usbdev_vm_close(struct vm_area_struct *vma) dec_usb_memory_use_count(usbm, &usbm->vma_use_count); } -struct vm_operations_struct usbdev_vm_ops = { +static struct vm_operations_struct usbdev_vm_ops = { .open = usbdev_vm_open, .close = usbdev_vm_close }; -- cgit v1.2.3 From feb26ac31a2a5cb88d86680d9a94916a6343e9e6 Mon Sep 17 00:00:00 2001 From: Chris Bainbridge Date: Mon, 25 Apr 2016 13:48:38 +0100 Subject: usb: core: hub: hub_port_init lock controller instead of bus The XHCI controller presents two USB buses to the system - one for USB2 and one for USB3. The hub init code (hub_port_init) is reentrant but only locks one bus per thread, leading to a race condition failure when two threads attempt to simultaneously initialise a USB2 and USB3 device: [ 8.034843] xhci_hcd 0000:00:14.0: Timeout while waiting for setup device command [ 13.183701] usb 3-3: device descriptor read/all, error -110 On a test system this failure occurred on 6% of all boots. The call traces at the point of failure are: Call Trace: [] schedule+0x37/0x90 [] usb_kill_urb+0x8d/0xd0 [] ? wake_up_atomic_t+0x30/0x30 [] usb_start_wait_urb+0xbe/0x150 [] usb_control_msg+0xbc/0xf0 [] hub_port_init+0x51e/0xb70 [] hub_event+0x817/0x1570 [] process_one_work+0x1ff/0x620 [] ? process_one_work+0x15f/0x620 [] worker_thread+0x64/0x4b0 [] ? rescuer_thread+0x390/0x390 [] kthread+0x105/0x120 [] ? kthread_create_on_node+0x200/0x200 [] ret_from_fork+0x3f/0x70 [] ? kthread_create_on_node+0x200/0x200 Call Trace: [] xhci_setup_device+0x53d/0xa40 [] xhci_address_device+0xe/0x10 [] hub_port_init+0x1bf/0xb70 [] ? trace_hardirqs_on+0xd/0x10 [] hub_event+0x817/0x1570 [] process_one_work+0x1ff/0x620 [] ? process_one_work+0x15f/0x620 [] worker_thread+0x64/0x4b0 [] ? rescuer_thread+0x390/0x390 [] kthread+0x105/0x120 [] ? kthread_create_on_node+0x200/0x200 [] ret_from_fork+0x3f/0x70 [] ? kthread_create_on_node+0x200/0x200 Which results from the two call chains: hub_port_init usb_get_device_descriptor usb_get_descriptor usb_control_msg usb_internal_control_msg usb_start_wait_urb usb_submit_urb / wait_for_completion_timeout / usb_kill_urb hub_port_init hub_set_address xhci_address_device xhci_setup_device Mathias Nyman explains the current behaviour violates the XHCI spec: hub_port_reset() will end up moving the corresponding xhci device slot to default state. As hub_port_reset() is called several times in hub_port_init() it sounds reasonable that we could end up with two threads having their xhci device slots in default state at the same time, which according to xhci 4.5.3 specs still is a big no no: "Note: Software shall not transition more than one Device Slot to the Default State at a time" So both threads fail at their next task after this. One fails to read the descriptor, and the other fails addressing the device. Fix this in hub_port_init by locking the USB controller (instead of an individual bus) to prevent simultaneous initialisation of both buses. Fixes: 638139eb95d2 ("usb: hub: allow to process more usb hub events in parallel") Link: https://lkml.org/lkml/2016/2/8/312 Link: https://lkml.org/lkml/2016/2/4/748 Signed-off-by: Chris Bainbridge Cc: stable Acked-by: Mathias Nyman Signed-off-by: Greg Kroah-Hartman --- drivers/usb/core/hcd.c | 15 +++++++++++++-- drivers/usb/core/hub.c | 8 ++++---- 2 files changed, 17 insertions(+), 6 deletions(-) (limited to 'drivers/usb/core') diff --git a/drivers/usb/core/hcd.c b/drivers/usb/core/hcd.c index 2ca2cef7f681..980fc5774151 100644 --- a/drivers/usb/core/hcd.c +++ b/drivers/usb/core/hcd.c @@ -994,7 +994,7 @@ static void usb_bus_init (struct usb_bus *bus) bus->bandwidth_allocated = 0; bus->bandwidth_int_reqs = 0; bus->bandwidth_isoc_reqs = 0; - mutex_init(&bus->usb_address0_mutex); + mutex_init(&bus->devnum_next_mutex); } /*-------------------------------------------------------------------------*/ @@ -2521,6 +2521,14 @@ struct usb_hcd *usb_create_shared_hcd(const struct hc_driver *driver, return NULL; } if (primary_hcd == NULL) { + hcd->address0_mutex = kmalloc(sizeof(*hcd->address0_mutex), + GFP_KERNEL); + if (!hcd->address0_mutex) { + kfree(hcd); + dev_dbg(dev, "hcd address0 mutex alloc failed\n"); + return NULL; + } + mutex_init(hcd->address0_mutex); hcd->bandwidth_mutex = kmalloc(sizeof(*hcd->bandwidth_mutex), GFP_KERNEL); if (!hcd->bandwidth_mutex) { @@ -2532,6 +2540,7 @@ struct usb_hcd *usb_create_shared_hcd(const struct hc_driver *driver, dev_set_drvdata(dev, hcd); } else { mutex_lock(&usb_port_peer_mutex); + hcd->address0_mutex = primary_hcd->address0_mutex; hcd->bandwidth_mutex = primary_hcd->bandwidth_mutex; hcd->primary_hcd = primary_hcd; primary_hcd->primary_hcd = primary_hcd; @@ -2598,8 +2607,10 @@ static void hcd_release(struct kref *kref) struct usb_hcd *hcd = container_of (kref, struct usb_hcd, kref); mutex_lock(&usb_port_peer_mutex); - if (usb_hcd_is_primary_hcd(hcd)) + if (usb_hcd_is_primary_hcd(hcd)) { + kfree(hcd->address0_mutex); kfree(hcd->bandwidth_mutex); + } if (hcd->shared_hcd) { struct usb_hcd *peer = hcd->shared_hcd; diff --git a/drivers/usb/core/hub.c b/drivers/usb/core/hub.c index c2270d8fac12..bee13517676f 100644 --- a/drivers/usb/core/hub.c +++ b/drivers/usb/core/hub.c @@ -2082,7 +2082,7 @@ static void choose_devnum(struct usb_device *udev) struct usb_bus *bus = udev->bus; /* be safe when more hub events are proceed in parallel */ - mutex_lock(&bus->usb_address0_mutex); + mutex_lock(&bus->devnum_next_mutex); if (udev->wusb) { devnum = udev->portnum + 1; BUG_ON(test_bit(devnum, bus->devmap.devicemap)); @@ -2100,7 +2100,7 @@ static void choose_devnum(struct usb_device *udev) set_bit(devnum, bus->devmap.devicemap); udev->devnum = devnum; } - mutex_unlock(&bus->usb_address0_mutex); + mutex_unlock(&bus->devnum_next_mutex); } static void release_devnum(struct usb_device *udev) @@ -4366,7 +4366,7 @@ hub_port_init(struct usb_hub *hub, struct usb_device *udev, int port1, if (oldspeed == USB_SPEED_LOW) delay = HUB_LONG_RESET_TIME; - mutex_lock(&hdev->bus->usb_address0_mutex); + mutex_lock(hcd->address0_mutex); /* Reset the device; full speed may morph to high speed */ /* FIXME a USB 2.0 device may morph into SuperSpeed on reset. */ @@ -4652,7 +4652,7 @@ fail: hub_port_disable(hub, port1, 0); update_devnum(udev, devnum); /* for disconnect processing */ } - mutex_unlock(&hdev->bus->usb_address0_mutex); + mutex_unlock(hcd->address0_mutex); return retval; } -- cgit v1.2.3 From dc5878abf49c06b9c1d3d161760957a98ab970bf Mon Sep 17 00:00:00 2001 From: Peter Chen Date: Mon, 25 Apr 2016 09:57:18 +0800 Subject: usb: core: move root hub's device node assignment after it is added to bus When the root hub device is added to the bus, it tries to get pins information from pinctrl (see pinctrl_bind_pins, at really_probe), if the pin information is described at DT, it will show below error since the root hub's device node is the same with controller's, but controller's pin has already been requested when it is added to platform bus. imx6q-pinctrl 20e0000.iomuxc: pin MX6Q_PAD_GPIO_1 already requested by 2184000.usb; cannot claim for usb1 imx6q-pinctrl 20e0000.iomuxc: pin-137 (usb1) status -22 imx6q-pinctrl 20e0000.iomuxc: could not request pin 137 (MX6Q_PAD_GPIO_1) from group usbotggrp-3 on device 20e0000.iomuxc usb usb1: Error applying setting, reverse things back To fix this issue, we move the root hub's device node assignment (equals to contrller's) after device is added to bus, we only need to know root hub's device node information after the device under root hub is created, so this movement will not affect current function. Signed-off-by: Peter Chen Reported-by: Lars Steubesand Signed-off-by: Greg Kroah-Hartman --- drivers/usb/core/hcd.c | 1 + drivers/usb/core/usb.c | 1 - 2 files changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers/usb/core') diff --git a/drivers/usb/core/hcd.c b/drivers/usb/core/hcd.c index 980fc5774151..34b837ae1ed7 100644 --- a/drivers/usb/core/hcd.c +++ b/drivers/usb/core/hcd.c @@ -1118,6 +1118,7 @@ static int register_root_hub(struct usb_hcd *hcd) /* Did the HC die before the root hub was registered? */ if (HCD_DEAD(hcd)) usb_hc_died (hcd); /* This time clean up */ + usb_dev->dev.of_node = parent_dev->of_node; } mutex_unlock(&usb_bus_idr_lock); diff --git a/drivers/usb/core/usb.c b/drivers/usb/core/usb.c index dcb85e3cd5a7..9cea6b0dec9c 100644 --- a/drivers/usb/core/usb.c +++ b/drivers/usb/core/usb.c @@ -472,7 +472,6 @@ struct usb_device *usb_alloc_dev(struct usb_device *parent, dev->route = 0; dev->dev.parent = bus->controller; - dev->dev.of_node = bus->controller->of_node; dev_set_name(&dev->dev, "usb%d", bus->busnum); root_hub = 1; } else { -- cgit v1.2.3 From 6fb650d43da3e7054984dc548eaa88765a94d49f Mon Sep 17 00:00:00 2001 From: Alan Stern Date: Fri, 29 Apr 2016 15:25:17 -0400 Subject: USB: leave LPM alone if possible when binding/unbinding interface drivers When a USB driver is bound to an interface (either through probing or by claiming it) or is unbound from an interface, the USB core always disables Link Power Management during the transition and then re-enables it afterward. The reason is because the driver might want to prevent hub-initiated link power transitions, in which case the HCD would have to recalculate the various LPM parameters. This recalculation takes place when LPM is re-enabled and the new parameters are sent to the device and its parent hub. However, if the driver does not want to prevent hub-initiated link power transitions then none of this work is necessary. The parameters don't need to be recalculated, and LPM doesn't need to be disabled and re-enabled. It turns out that disabling and enabling LPM can be time-consuming, enough so that it interferes with user programs that want to claim and release interfaces rapidly via usbfs. Since the usbfs kernel driver doesn't set the disable_hub_initiated_lpm flag, we can speed things up and get the user programs to work by leaving LPM alone whenever the flag isn't set. And while we're improving the way disable_hub_initiated_lpm gets used, let's also fix its kerneldoc. Signed-off-by: Alan Stern Tested-by: Matthew Giassa CC: Mathias Nyman CC: Signed-off-by: Greg Kroah-Hartman --- drivers/usb/core/driver.c | 40 +++++++++++++++++++++++----------------- 1 file changed, 23 insertions(+), 17 deletions(-) (limited to 'drivers/usb/core') diff --git a/drivers/usb/core/driver.c b/drivers/usb/core/driver.c index 2057d91d8336..dadd1e8dfe09 100644 --- a/drivers/usb/core/driver.c +++ b/drivers/usb/core/driver.c @@ -284,7 +284,7 @@ static int usb_probe_interface(struct device *dev) struct usb_device *udev = interface_to_usbdev(intf); const struct usb_device_id *id; int error = -ENODEV; - int lpm_disable_error; + int lpm_disable_error = -ENODEV; dev_dbg(dev, "%s\n", __func__); @@ -336,12 +336,14 @@ static int usb_probe_interface(struct device *dev) * setting during probe, that should also be fine. usb_set_interface() * will attempt to disable LPM, and fail if it can't disable it. */ - lpm_disable_error = usb_unlocked_disable_lpm(udev); - if (lpm_disable_error && driver->disable_hub_initiated_lpm) { - dev_err(&intf->dev, "%s Failed to disable LPM for driver %s\n.", - __func__, driver->name); - error = lpm_disable_error; - goto err; + if (driver->disable_hub_initiated_lpm) { + lpm_disable_error = usb_unlocked_disable_lpm(udev); + if (lpm_disable_error) { + dev_err(&intf->dev, "%s Failed to disable LPM for driver %s\n.", + __func__, driver->name); + error = lpm_disable_error; + goto err; + } } /* Carry out a deferred switch to altsetting 0 */ @@ -391,7 +393,8 @@ static int usb_unbind_interface(struct device *dev) struct usb_interface *intf = to_usb_interface(dev); struct usb_host_endpoint *ep, **eps = NULL; struct usb_device *udev; - int i, j, error, r, lpm_disable_error; + int i, j, error, r; + int lpm_disable_error = -ENODEV; intf->condition = USB_INTERFACE_UNBINDING; @@ -399,12 +402,13 @@ static int usb_unbind_interface(struct device *dev) udev = interface_to_usbdev(intf); error = usb_autoresume_device(udev); - /* Hub-initiated LPM policy may change, so attempt to disable LPM until + /* If hub-initiated LPM policy may change, attempt to disable LPM until * the driver is unbound. If LPM isn't disabled, that's fine because it * wouldn't be enabled unless all the bound interfaces supported * hub-initiated LPM. */ - lpm_disable_error = usb_unlocked_disable_lpm(udev); + if (driver->disable_hub_initiated_lpm) + lpm_disable_error = usb_unlocked_disable_lpm(udev); /* * Terminate all URBs for this interface unless the driver @@ -505,7 +509,7 @@ int usb_driver_claim_interface(struct usb_driver *driver, struct device *dev; struct usb_device *udev; int retval = 0; - int lpm_disable_error; + int lpm_disable_error = -ENODEV; if (!iface) return -ENODEV; @@ -526,12 +530,14 @@ int usb_driver_claim_interface(struct usb_driver *driver, iface->condition = USB_INTERFACE_BOUND; - /* Disable LPM until this driver is bound. */ - lpm_disable_error = usb_unlocked_disable_lpm(udev); - if (lpm_disable_error && driver->disable_hub_initiated_lpm) { - dev_err(&iface->dev, "%s Failed to disable LPM for driver %s\n.", - __func__, driver->name); - return -ENOMEM; + /* See the comment about disabling LPM in usb_probe_interface(). */ + if (driver->disable_hub_initiated_lpm) { + lpm_disable_error = usb_unlocked_disable_lpm(udev); + if (lpm_disable_error) { + dev_err(&iface->dev, "%s Failed to disable LPM for driver %s\n.", + __func__, driver->name); + return -ENOMEM; + } } /* Claimed interfaces are initially inactive (suspended) and -- cgit v1.2.3 From 681fef8380eb818c0b845fca5d2ab1dcbab114ee Mon Sep 17 00:00:00 2001 From: Kangjie Lu Date: Tue, 3 May 2016 16:32:16 -0400 Subject: USB: usbfs: fix potential infoleak in devio MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit The stack object “ci” has a total size of 8 bytes. Its last 3 bytes are padding bytes which are not initialized and leaked to userland via “copy_to_user”. Signed-off-by: Kangjie Lu Signed-off-by: Greg Kroah-Hartman --- drivers/usb/core/devio.c | 9 +++++---- 1 file changed, 5 insertions(+), 4 deletions(-) (limited to 'drivers/usb/core') diff --git a/drivers/usb/core/devio.c b/drivers/usb/core/devio.c index 73ce87166401..e9f5043a2167 100644 --- a/drivers/usb/core/devio.c +++ b/drivers/usb/core/devio.c @@ -1316,10 +1316,11 @@ static int proc_getdriver(struct usb_dev_state *ps, void __user *arg) static int proc_connectinfo(struct usb_dev_state *ps, void __user *arg) { - struct usbdevfs_connectinfo ci = { - .devnum = ps->dev->devnum, - .slow = ps->dev->speed == USB_SPEED_LOW - }; + struct usbdevfs_connectinfo ci; + + memset(&ci, 0, sizeof(ci)); + ci.devnum = ps->dev->devnum; + ci.slow = ps->dev->speed == USB_SPEED_LOW; if (copy_to_user(arg, &ci, sizeof(ci))) return -EFAULT; -- cgit v1.2.3 From 81099f97bd31e25ff2719a435b1860fc3876122f Mon Sep 17 00:00:00 2001 From: Hans de Goede Date: Thu, 19 May 2016 17:12:19 +0200 Subject: usb: quirks: Fix sorting Properly sort all the entries by vendor id. Signed-off-by: Hans de Goede Cc: stable Signed-off-by: Greg Kroah-Hartman --- drivers/usb/core/quirks.c | 20 ++++++++++---------- 1 file changed, 10 insertions(+), 10 deletions(-) (limited to 'drivers/usb/core') diff --git a/drivers/usb/core/quirks.c b/drivers/usb/core/quirks.c index 6dc810bce295..8130e38cae9d 100644 --- a/drivers/usb/core/quirks.c +++ b/drivers/usb/core/quirks.c @@ -44,6 +44,9 @@ static const struct usb_device_id usb_quirk_list[] = { /* Creative SB Audigy 2 NX */ { USB_DEVICE(0x041e, 0x3020), .driver_info = USB_QUIRK_RESET_RESUME }, + /* USB3503 */ + { USB_DEVICE(0x0424, 0x3503), .driver_info = USB_QUIRK_RESET_RESUME }, + /* Microsoft Wireless Laser Mouse 6000 Receiver */ { USB_DEVICE(0x045e, 0x00e1), .driver_info = USB_QUIRK_RESET_RESUME }, @@ -173,6 +176,10 @@ static const struct usb_device_id usb_quirk_list[] = { /* MAYA44USB sound device */ { USB_DEVICE(0x0a92, 0x0091), .driver_info = USB_QUIRK_RESET_RESUME }, + /* ASUS Base Station(T100) */ + { USB_DEVICE(0x0b05, 0x17e0), .driver_info = + USB_QUIRK_IGNORE_REMOTE_WAKEUP }, + /* Action Semiconductor flash disk */ { USB_DEVICE(0x10d6, 0x2200), .driver_info = USB_QUIRK_STRING_FETCH_255 }, @@ -188,16 +195,6 @@ static const struct usb_device_id usb_quirk_list[] = { { USB_DEVICE(0x1908, 0x1315), .driver_info = USB_QUIRK_HONOR_BNUMINTERFACES }, - /* INTEL VALUE SSD */ - { USB_DEVICE(0x8086, 0xf1a5), .driver_info = USB_QUIRK_RESET_RESUME }, - - /* USB3503 */ - { USB_DEVICE(0x0424, 0x3503), .driver_info = USB_QUIRK_RESET_RESUME }, - - /* ASUS Base Station(T100) */ - { USB_DEVICE(0x0b05, 0x17e0), .driver_info = - USB_QUIRK_IGNORE_REMOTE_WAKEUP }, - /* Protocol and OTG Electrical Test Device */ { USB_DEVICE(0x1a0a, 0x0200), .driver_info = USB_QUIRK_LINEAR_UFRAME_INTR_BINTERVAL }, @@ -208,6 +205,9 @@ static const struct usb_device_id usb_quirk_list[] = { /* Blackmagic Design UltraStudio SDI */ { USB_DEVICE(0x1edb, 0xbd4f), .driver_info = USB_QUIRK_NO_LPM }, + /* INTEL VALUE SSD */ + { USB_DEVICE(0x8086, 0xf1a5), .driver_info = USB_QUIRK_RESET_RESUME }, + { } /* terminating entry must be last */ }; -- cgit v1.2.3 From 32cb0b37098f4beeff5ad9e325f11b42a6ede56c Mon Sep 17 00:00:00 2001 From: Hans de Goede Date: Thu, 19 May 2016 17:12:20 +0200 Subject: usb: quirks: Add no-lpm quirk for Acer C120 LED Projector The Acer C120 LED Projector is a USB-3 connected pico projector which takes both its power and video data from USB-3. In combination with some hubs this device does not play well with lpm, so disable lpm for it. Signed-off-by: Hans de Goede Cc: stable Signed-off-by: Greg Kroah-Hartman --- drivers/usb/core/quirks.c | 3 +++ 1 file changed, 3 insertions(+) (limited to 'drivers/usb/core') diff --git a/drivers/usb/core/quirks.c b/drivers/usb/core/quirks.c index 8130e38cae9d..944a6dca0fcb 100644 --- a/drivers/usb/core/quirks.c +++ b/drivers/usb/core/quirks.c @@ -199,6 +199,9 @@ static const struct usb_device_id usb_quirk_list[] = { { USB_DEVICE(0x1a0a, 0x0200), .driver_info = USB_QUIRK_LINEAR_UFRAME_INTR_BINTERVAL }, + /* Acer C120 LED Projector */ + { USB_DEVICE(0x1de1, 0xc102), .driver_info = USB_QUIRK_NO_LPM }, + /* Blackmagic Design Intensity Shuttle */ { USB_DEVICE(0x1edb, 0xbd3b), .driver_info = USB_QUIRK_NO_LPM }, -- cgit v1.2.3