| Age | Commit message (Collapse) | Author |
|---|
|
In preparation for handling processing modules with different
input/output pin counts, introduce two new tokens for input/output
audio format counts. Use these token values to parse all the available
audio formats from topology.
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20230313124856.8140-11-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Introduce a new struct sof_ipc4_pin_format which contains the pin index
and the buffer size. Replace the type of available input/output audio
formats in struct sof_ipc4_available_audio_format with this new struct
type and rename them to input_pin_fmts and output_pin_fmts.
Also, add a new token, SOF_TKN_CAVS_AUDIO_FORMAT_PIN_INDEX that will be
used to parse the pin index for the audio format from topology.
Currently we only set the audio format for Pin 0 in topology, so the
default value will be 0 for all audio formats.
Finally, parse the pin_index and the input/output buffer sizes
along with audio formats into the pin_format arrays in struct
sof_ipc4_available_audio_format. This makes the base_config array in struct
sof_ipc4_available_audio_format redundant. So remove it. This change
will allow the addition of audio formats for the non-zero pins in
topology transparent to the topology parser in the kernel.
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20230313124856.8140-8-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Do not parse the SOF_TKN_CAVS_AUDIO_FORMAT_DMA_BUFFER_SIZE token as the
dma_buffer_size can be derived from the input/output buffer size and the
type of widget during copier prepare. For the deep buffer case,
introduce a new token that will be used to get the deep buffer DMA size
for the host copier from topology.
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20230313124856.8140-5-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Currently we use input/output and sink/source pins interchangeably.
Remove the references to sink/source pins and replace with input/output
pins everywhere for consistency and clarity.
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20230313124856.8140-3-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Rename SOF_TKN_CAVS_AUDIO_FORMAT_IN_VALID and
SOF_TKN_CAVS_AUDIO_FORMAT_OUT_VALID as
SOF_TKN_CAVS_AUDIO_FORMAT_IN_VALID_BIT_DEPTH and
SOF_TKN_CAVS_AUDIO_FORMAT_OUT_VALID_BIT_DEPTH respectively.
These are currently not used.
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20230313124856.8140-2-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
With IPC4 the sof_abit_hdr is only used between user space
(and in topology) and kernel.
The same abi header is used with small differencies like different
magic number and the type field have slightly different name, but
similar function in IPC4 (param_id).
Update the kernel documentation to highlight the differences.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Jaska Uimonen <jaska.uimonen@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20230313110344.16644-5-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Replace the comments for sof_abi_hdr to kernel style.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Jaska Uimonen <jaska.uimonen@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20230313110344.16644-4-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Reflect the change from the commit below.
Fixes: cb5a065b4ea9 ("headers/deps: mm: Split <linux/gfp_types.h> out of <linux/gfp.h>")
Signed-off-by: Thorsten Scherer <t.scherer@eckelmann.de>
Acked-by: Hyeonggon Yoo <42.hyeyoo@gmail.com>
Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
|
|
I²C peripheral devices that are connected to the controller are
represented in the Linux kernel as objects of the struct i2c_client.
Fix this in the header file.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230302161206.38106-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
Linux 6.3-rc2
|
|
Linux 6.3-rc2
|
|
Linux 6.3-rc2
|
|
Backmerging to get latest upstream.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
|
|
Backmerging to get v6.3-rc1 and sync with the other DRM trees.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
|
|
On s390 PCI functions may be hotplugged individually even when they
belong to a multi-function device. In particular on an SR-IOV device VFs
may be removed and later re-added.
In commit a50297cf8235 ("s390/pci: separate zbus creation from
scanning") it was missed however that struct pci_bus and struct
zpci_bus's resource list retained a reference to the PCI functions MMIO
resources even though those resources are released and freed on
hot-unplug. These stale resources may subsequently be claimed when the
PCI function re-appears resulting in use-after-free.
One idea of fixing this use-after-free in s390 specific code that was
investigated was to simply keep resources around from the moment a PCI
function first appeared until the whole virtual PCI bus created for
a multi-function device disappears. The problem with this however is
that due to the requirement of artificial MMIO addreesses (address
cookies) extra logic is then needed to keep the address cookies
compatible on re-plug. At the same time the MMIO resources semantically
belong to the PCI function so tying their lifecycle to the function
seems more logical.
Instead a simpler approach is to remove the resources of an individually
hot-unplugged PCI function from the PCI bus's resource list while
keeping the resources of other PCI functions on the PCI bus untouched.
This is done by introducing pci_bus_remove_resource() to remove an
individual resource. Similarly the resource also needs to be removed
from the struct zpci_bus's resource list. It turns out however, that
there is really no need to add the MMIO resources to the struct
zpci_bus's resource list at all and instead we can simply use the
zpci_bar_struct's resource pointer directly.
Fixes: a50297cf8235 ("s390/pci: separate zbus creation from scanning")
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Reviewed-by: Matthew Rosato <mjrosato@linux.ibm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://lore.kernel.org/r/20230306151014.60913-2-schnelle@linux.ibm.com
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
|
|
Add new helper functions, drm_atomic_get_old_crtc_for_encoder
and drm_atomic_get_new_crtc_for_encoder to retrieve the
corresponding crtc for the encoder.
Signed-off-by: Sankeerth Billakanti <quic_sbillaka@quicinc.com>
Signed-off-by: Vinod Polimera <quic_vpolimer@quicinc.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Patchwork: https://patchwork.freedesktop.org/patch/524718/
Link: https://lore.kernel.org/r/1677774797-31063-2-git-send-email-quic_vpolimer@quicinc.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
|
|
The last remaining user of folio_write_one through the write_one_page
wrapper is jfs, so move the functionality there and hard code the
call to metapage_writepage.
Note that the use of the pagecache by the JFS 'metapage' buffer cache
is a bit odd, and we could probably do without VM-level dirty tracking
at all, but that's a change for another time.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Dave Kleikamp <dave.kleikamp@oracle.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4
Pull ext4 fixes from Ted Ts'o:
"Bug fixes and regressions for ext4, the most serious of which is a
potential deadlock during directory renames that was introduced during
the merge window discovered by a combination of syzbot and lockdep"
* tag 'ext4_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
ext4: zero i_disksize when initializing the bootloader inode
ext4: make sure fs error flag setted before clear journal error
ext4: commit super block if fs record error when journal record without error
ext4, jbd2: add an optimized bmap for the journal inode
ext4: fix WARNING in ext4_update_inline_data
ext4: move where set the MAY_INLINE_DATA flag is set
ext4: Fix deadlock during directory rename
ext4: Fix comment about the 64BIT feature
docs: ext4: modify the group desc size to 64
ext4: fix another off-by-one fsmap error on 1k block filesystems
ext4: fix RENAME_WHITEOUT handling for inline directories
ext4: make kobj_type structures constant
ext4: fix cgroup writeback accounting with fs-layer encryption
|
|
The cpumask_check() was unnecessarily tight, and causes problems for the
users of cpumask_next().
We have a number of users that take the previous return value of one of
the bit scanning functions and subtract one to keep it in "range". But
since the scanning functions end up returning up to 'small_cpumask_bits'
instead of the tighter 'nr_cpumask_bits', the range really needs to be
using that widened form.
[ This "previous-1" behavior is also the reason we have all those
comments about /* -1 is a legal arg here. */ and separate checks for
that being ok. So we could have just made "small_cpumask_bits-1"
be a similar special "don't check this" value.
Tetsuo Handa even suggested a patch that only does that for
cpumask_next(), since that seems to be the only actual case that
triggers, but that all makes it even _more_ magical and special. So
just relax the check ]
One example of this kind of pattern being the 'c_start()' function in
arch/x86/kernel/cpu/proc.c, but also duplicated in various forms on
other architectures.
Reported-by: syzbot+96cae094d90877641f32@syzkaller.appspotmail.com
Link: https://syzkaller.appspot.com/bug?extid=96cae094d90877641f32
Reported-by: Tetsuo Handa <penguin-kernel@i-love.sakura.ne.jp>
Link: https://lore.kernel.org/lkml/c1f4cc16-feea-b83c-82cf-1a1f007b7eb9@I-love.SAKURA.ne.jp/
Fixes: 596ff4a09b89 ("cpumask: re-introduce constant-sized cpumask optimizations")
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The next patch adds helpers like create_io_thread, but for use by the
vhost layer. There are several functions, so they are in their own file
instead of cluttering up fork.c. This patch allows that new file to
call copy_process.
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Christian Brauner (Microsoft) <brauner@kernel.org>
|
|
Since:
commit 10ab825bdef8 ("change kernel threads to ignore signals instead of
blocking them")
kthreads have been ignoring signals by default, and the vhost layer has
never had a need to change that. This patch adds an option flag,
USER_WORKER_SIG_IGN, handled in copy_process() after copy_sighand()
and copy_signals() so vhost_tasks added in the next patches can continue
to ignore singals.
Signed-off-by: Christian Brauner <brauner@kernel.org>
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Christian Brauner (Microsoft) <brauner@kernel.org>
|
|
Each vhost device gets a thread that is used to perform IO and management
operations. Instead of a thread that is accessing a device, the thread is
part of the device, so when it creates a thread using a helper based on
copy_process we can't dup or clone the parent's files/FDS because it
would do an extra increment on ourself.
Later, when we do:
Qemu process exits:
do_exit -> exit_files -> put_files_struct -> close_files
we would leak the device's resources because of that extra refcount
on the fd or file_struct.
This patch adds a no_files option so these worker threads can prevent
taking an extra refcount on themselves.
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Acked-by: Christian Brauner <brauner@kernel.org>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Christian Brauner (Microsoft) <brauner@kernel.org>
|
|
This adds a new flag, PF_USER_WORKER, that's used for behavior common to
to both PF_IO_WORKER and users like vhost which will use a new helper
instead of create_io_thread because they require different behavior for
operations like signal handling.
The common behavior PF_USER_WORKER covers is the vm reclaim handling.
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Christian Brauner (Microsoft) <brauner@kernel.org>
|
|
We only set args->io_thread/kthread to 0 or 1 then test if they are set,
so make them bit fields.
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Christian Brauner (Microsoft) <brauner@kernel.org>
|
|
This patch allows kernel users to pass in the thread name so it can be
set during creation instead of having to use set_task_comm after the
thread is created.
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Christian Brauner (Microsoft) <brauner@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c updates from Wolfram Sang:
"This marks the end of a transition to let I2C have the same probe
semantics as other subsystems. Uwe took care that no drivers in the
current tree nor in -next use the deprecated .probe call. So, it is a
good time to switch to the new, standard semantics now.
There is also a regression fix:
- regression fix for the notifier handling of the I2C core
- final coversions of drivers away from deprecated .probe
- make .probe_new the standard probe and convert I2C core to use it
* tag 'i2c-for-6.3-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: dev: Fix bus callback return values
i2c: Convert drivers to new .probe() callback
i2c: mux: Convert all drivers to new .probe() callback
i2c: Switch .probe() to not take an id parameter
media: i2c: ov2685: convert to i2c's .probe_new()
media: i2c: ov5695: convert to i2c's .probe_new()
w1: ds2482: Convert to i2c's .probe_new()
serial: sc16is7xx: Convert to i2c's .probe_new()
mtd: maps: pismo: Convert to i2c's .probe_new()
misc: ad525x_dpot-i2c: Convert to i2c's .probe_new()
|
|
call
Supporting multi-cs in spi drivers would require the chip_select & cs_gpiod
members of struct spi_device to be an array. But changing the type of these
members to array would break the spi driver functionality. To make the
transition smoother introduced four new APIs to get/set the
spi->chip_select & spi->cs_gpiod and replaced all spi->chip_select and
spi->cs_gpiod references with get or set API calls.
While adding multi-cs support in further patches the chip_select & cs_gpiod
members of the spi_device structure would be converted to arrays & the
"idx" parameter of the APIs would be used as array index i.e.,
spi->chip_select[idx] & spi->cs_gpiod[idx] respectively.
Signed-off-by: Amit Kumar Mahapatra <amit.kumar-mahapatra@amd.com>
Acked-by: Heiko Stuebner <heiko@sntech.de> # Rockchip drivers
Reviewed-by: Michal Simek <michal.simek@amd.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org> # Aspeed driver
Reviewed-by: Dhruva Gole <d-gole@ti.com> # SPI Cadence QSPI
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com> # spi-stm32-qspi
Acked-by: William Zhang <william.zhang@broadcom.com> # bcm63xx-hsspi driver
Reviewed-by: Serge Semin <fancer.lancer@gmail.com> # DW SSI part
Link: https://lore.kernel.org/r/167847070432.26.15076794204368669839@mailman-core.alsa-project.org
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Rename the function to iio_trigger_poll_nested. Add kernel-doc with
a note on the context where the function is expected to be called.
Signed-off-by: Mehdi Djait <mehdi.djait.k@gmail.com>
Link: https://lore.kernel.org/r/841b533cba28ca25a8e87280c44e45979166e8e2.1677761379.git.mehdi.djait.k@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Move the kernel-doc of the function to industrialio-trigger.c
Add a note on the context where the function is expected to be called.
Signed-off-by: Mehdi Djait <mehdi.djait.k@gmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/bd84fc17e9d22eab998bf48720297f9a77689f45.1677761379.git.mehdi.djait.k@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Having a per-vcpu virtual offset is a pain. It needs to be synchronized
on each update, and expands badly to a setup where different timers can
have different offsets, or have composite offsets (as with NV).
So let's start by replacing the use of the CNTVOFF_EL2 shadow register
(which we want to reclaim for NV anyway), and make the virtual timer
carry a pointer to a VM-wide offset.
This simplifies the code significantly. It also addresses two terrible bugs:
- The use of CNTVOFF_EL2 leads to some nice offset corruption
when the sysreg gets reset, as reported by Joey.
- The kvm mutex is taken from a vcpu ioctl, which goes against
the locking rules...
Reported-by: Joey Gouly <joey.gouly@arm.com>
Reviewed-by: Reiji Watanabe <reijiw@google.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20230224173915.GA17407@e124191.cambridge.arm.com
Tested-by: Joey Gouly <joey.gouly@arm.com>
Link: https://lore.kernel.org/r/20230224191640.3396734-1-maz@kernel.org
Signed-off-by: Oliver Upton <oliver.upton@linux.dev>
|
|
The generic bmap() function exported by the VFS takes locks and does
checks that are not necessary for the journal inode. So allow the
file system to set a journal-optimized bmap function in
journal->j_bmap.
Reported-by: syzbot+9543479984ae9e576000@syzkaller.appspotmail.com
Link: https://syzkaller.appspot.com/bug?id=e4aaa78795e490421c79f76ec3679006c8ff4cf0
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
|
|
Introduce xdp_set_features_flag utility routine in order to update
dynamically xdp_features according to the dynamic hw configuration via
ethtool (e.g. changing number of hw rx/tx queues).
Add xdp_clear_features_flag() in order to clear all xdp_feature flag.
Reviewed-by: Shay Agroskin <shayagr@amazon.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull put_and_unmap_page() helper from Al Viro:
"kmap_local_page() conversions in local filesystems keep running into
kunmap_local_page()+put_page() combinations. We can keep inventing
names for identical inline helpers, but it's getting rather
inconvenient. I've added a trivial helper to linux/highmem.h instead.
I would've held that back until the merge window, if not for the mess
it causes in tree topology - I've several branches merging from that
one, and it's only going to get worse if e.g. ext2 stuff gets picked
by Jan"
* tag 'pull-highmem' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
new helper: put_and_unmap_page()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next
Johannes Berg says:
====================
wireless-next patches for 6.4
Major changes:
cfg80211
* 6 GHz improvements
* HW timestamping support
* support for randomized auth/deauth TA for PASN privacy
(also for mac80211)
mac80211
* radiotap TLV and EHT support for the iwlwifi sniffer
* HW timestamping support
* per-link debugfs for multi-link
brcmfmac
* support for Apple (M1 Pro/Max) devices
iwlwifi
* support for a few new devices
* EHT sniffer support
rtw88
* better support for some SDIO devices
(e.g. MAC address from efuse)
rtw89
* HW scan support for 8852b
* better support for 6 GHz scanning
* tag 'wireless-next-2023-03-10' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next: (84 commits)
wifi: iwlwifi: mvm: fix EOF bit reporting
wifi: iwlwifi: Do not include radiotap EHT user info if not needed
wifi: iwlwifi: mvm: add EHT RU allocation to radiotap
wifi: iwlwifi: Update logs for yoyo reset sw changes
wifi: iwlwifi: mvm: clean up duplicated defines
wifi: iwlwifi: rs-fw: break out for unsupported bandwidth
wifi: iwlwifi: Add support for B step of BnJ-Fm4
wifi: iwlwifi: mvm: make flush code a bit clearer
wifi: iwlwifi: mvm: avoid UB shift of snif_queue
wifi: iwlwifi: mvm: add primary 80 known for EHT radiotap
wifi: iwlwifi: mvm: parse FW frame metadata for EHT sniffer mode
wifi: iwlwifi: mvm: decode USIG_B1_B7 RU to nl80211 RU width
wifi: iwlwifi: mvm: rename define to generic name
wifi: iwlwifi: mvm: allow Microsoft to use TAS
wifi: iwlwifi: mvm: add all EHT based on data0 info from HW
wifi: iwlwifi: mvm: add EHT radiotap info based on rate_n_flags
wifi: iwlwifi: mvm: add an helper function radiotap TLVs
wifi: radiotap: separate vendor TLV into header/content
wifi: iwlwifi: reduce verbosity of some logging events
wifi: iwlwifi: Adding the code to get RF name for MsP device
...
====================
Link: https://lore.kernel.org/r/20230310120159.36518-1-johannes@sipsolutions.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
If a PTR_TO_BTF_ID type comes from program BTF - not vmlinux or module
BTF - it must have been allocated by bpf_obj_new and therefore must be
free'd with bpf_obj_drop. Such a PTR_TO_BTF_ID is considered a "local
kptr" and is tagged with MEM_ALLOC type tag by bpf_obj_new.
This patch adds support for treating __kptr-tagged pointers to "local
kptrs" as having an implicit bpf_obj_drop destructor for referenced kptr
acquire / release semantics. Consider the following example:
struct node_data {
long key;
long data;
struct bpf_rb_node node;
};
struct map_value {
struct node_data __kptr *node;
};
struct {
__uint(type, BPF_MAP_TYPE_ARRAY);
__type(key, int);
__type(value, struct map_value);
__uint(max_entries, 1);
} some_nodes SEC(".maps");
If struct node_data had a matching definition in kernel BTF, the verifier would
expect a destructor for the type to be registered. Since struct node_data does
not match any type in kernel BTF, the verifier knows that there is no kfunc
that provides a PTR_TO_BTF_ID to this type, and that such a PTR_TO_BTF_ID can
only come from bpf_obj_new. So instead of searching for a registered dtor,
a bpf_obj_drop dtor can be assumed.
This allows the runtime to properly destruct such kptrs in
bpf_obj_free_fields, which enables maps to clean up map_vals w/ such
kptrs when going away.
Implementation notes:
* "kernel_btf" variable is renamed to "kptr_btf" in btf_parse_kptr.
Before this patch, the variable would only ever point to vmlinux or
module BTFs, but now it can point to some program BTF for local kptr
type. It's later used to populate the (btf, btf_id) pair in kptr btf
field.
* It's necessary to btf_get the program BTF when populating btf_field
for local kptr. btf_record_free later does a btf_put.
* Behavior for non-local referenced kptrs is not modified, as
bpf_find_btf_id helper only searches vmlinux and module BTFs for
matching BTF type. If such a type is found, btf_field_kptr's btf will
pass btf_is_kernel check, and the associated release function is
some one-argument dtor. If btf_is_kernel check fails, associated
release function is two-arg bpf_obj_drop_impl. Before this patch
only btf_field_kptr's w/ kernel or module BTFs were created.
Signed-off-by: Dave Marchevsky <davemarchevsky@fb.com>
Link: https://lore.kernel.org/r/20230310230743.2320707-2-davemarchevsky@fb.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
Introduce LSM_ORDER_LAST, to satisfy the requirement of LSMs needing to be
last, e.g. the 'integrity' LSM, without changing the kernel command line or
configuration.
Also, set this order for the 'integrity' LSM. While not enforced, this is
the only LSM expected to use it.
Similarly to LSM_ORDER_FIRST, LSMs with LSM_ORDER_LAST are always enabled
and put at the end of the LSM list, if selected in the kernel
configuration. Setting one of these orders alone, does not cause the LSMs
to be selected and compiled built-in in the kernel.
Finally, for LSM_ORDER_MUTABLE LSMs, set the found variable to true if an
LSM is found, regardless of its order. In this way, the kernel would not
wrongly report that the LSM is not built-in in the kernel if its order is
LSM_ORDER_LAST.
Fixes: 79f7865d844c ("LSM: Introduce "lsm=" for boottime LSM selection")
Signed-off-by: Roberto Sassu <roberto.sassu@huawei.com>
Acked-by: Mimi Zohar <zohar@linux.ibm.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>
|
|
Fix bug of the extra newline characters in debugfs logs. When a
line is added to debugfs with a newline character at the end,
an extra line appears in the debugfs log.
This is due to a discrepancy between how the lines are printed and how they
are added to the logs. Remove this discrepancy by checking if a newline
character is present before adding a newline character. This should closely
match the printk behavior.
Add kunit_log_newline_test to provide test coverage for this issue. (Also,
move kunit_log_test above suite definition to remove the unnecessary
declaration prior to the suite definition)
As an example, say we add these two lines to the log:
kunit_log(..., "KTAP version 1\n");
kunit_log(..., "1..1");
The debugfs log before this fix:
KTAP version 1
1..1
The debugfs log after this fix:
KTAP version 1
1..1
Signed-off-by: Rae Moar <rmoar@google.com>
Reviewed-by: David Gow <davidgow@google.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
|
|
Fix bug in debugfs logs that causes individual parameterized results to not
appear because the log is reinitialized (cleared) when each parameter is
run.
Ensure these results appear in the debugfs logs, increase log size to
allow for the size of parameterized results. As a result, append lines to
the log directly rather than using an intermediate variable that can cause
stack size warnings due to the increased log size.
Here is the debugfs log of ext4_inode_test which uses parameterized tests
before the fix:
KTAP version 1
# Subtest: ext4_inode_test
1..1
# Totals: pass:16 fail:0 skip:0 total:16
ok 1 ext4_inode_test
As you can see, this log does not include any of the individual
parametrized results.
After (in combination with the next two fixes to remove extra empty line
and ensure KTAP valid format):
KTAP version 1
1..1
KTAP version 1
# Subtest: ext4_inode_test
1..1
KTAP version 1
# Subtest: inode_test_xtimestamp_decoding
ok 1 1901-12-13 Lower bound of 32bit < 0 timestamp, no extra bits
... (the rest of the individual parameterized tests)
ok 16 2446-05-10 Upper bound of 32bit >=0 timestamp. All extra
# inode_test_xtimestamp_decoding: pass:16 fail:0 skip:0 total:16
ok 1 inode_test_xtimestamp_decoding
# Totals: pass:16 fail:0 skip:0 total:16
ok 1 ext4_inode_test
Signed-off-by: Rae Moar <rmoar@google.com>
Reviewed-by: David Gow <davidgow@google.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
|
|
btf_record_find's 3rd parameter can be multiple enum btf_field_type's
masked together. The function is called with BPF_KPTR in two places in
verifier.c, so it works with masked values already.
Signed-off-by: Dave Marchevsky <davemarchevsky@fb.com>
Link: https://lore.kernel.org/r/20230309180111.1618459-4-davemarchevsky@fb.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
CONFIG_* switches should not be exposed in uapi headers, thus let's get
rid of the USE_WCACHING macro here (which was also named way to generic)
and integrate the logic directly in the only function that needs it.
Suggested-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
This has a "#ifdef CONFIG_*" that used to be exposed to userspace.
The names in here are so generic that I don't think it's a good idea
to expose them to userspace (or even the rest of the kernel). There are
multiple in-kernel users, so it's been moved to a kernel header file.
Signed-off-by: Palmer Dabbelt <palmer@dabbelt.com>
Reviewed-by: Andrew Waterman <waterman@eecs.berkeley.edu>
Reviewed-by: Albert Ou <aou@eecs.berkeley.edu>
Message-Id: <1447119071-19392-10-git-send-email-palmer@dabbelt.com>
[thuth: Remove it also from tools/include/uapi/linux/hw_breakpoint.h]
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
This doesn't make any sense to expose to userspace, so it's been moved
to the one user. This was introduced by commit 95f19f658ce1 ("epoll:
drop EPOLLWAKEUP if PM_SLEEP is disabled").
Signed-off-by: Palmer Dabbelt <palmer@dabbelt.com>
Reviewed-by: Andrew Waterman <waterman@eecs.berkeley.edu>
Reviewed-by: Albert Ou <aou@eecs.berkeley.edu>
Message-Id: <1447119071-19392-7-git-send-email-palmer@dabbelt.com>
[thuth: Rebased to fix contextual conflicts]
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
This used to be behind an #ifdef COMPAT_COMPAT, so most of userspace
wouldn't have seen the definition before. Unfortunately this header
file became visible to userspace, so the definition has instead been
moved to net/atm/svc.c (the only user).
Signed-off-by: Palmer Dabbelt <palmer@dabbelt.com>
Reviewed-by: Andrew Waterman <waterman@eecs.berkeley.edu>
Reviewed-by: Albert Ou <aou@eecs.berkeley.edu>
Message-Id: <1447119071-19392-4-git-send-email-palmer@dabbelt.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
This patch refactors the selem freeing logic into bpf_selem_free().
It is a preparation work for a later patch using
bpf_mem_cache_alloc/free. The other kfree(selem) cases
are also changed to bpf_selem_free(..., reuse_now = true).
Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org>
Link: https://lore.kernel.org/r/20230308065936.1550103-10-martin.lau@linux.dev
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
This patch re-purpose the use_trace_rcu to mean
if the freed memory can be reused immediately or not.
The use_trace_rcu is renamed to reuse_now. Other than
the boolean test is reversed, it should be a no-op.
The following explains the reason for the rename and how it will
be used in a later patch.
In a later patch, bpf_mem_cache_alloc/free will be used
in the bpf_local_storage. The bpf mem allocator will reuse
the freed memory immediately. Some of the free paths in
bpf_local_storage does not support memory to be reused immediately.
These paths are the "delete" elem cases from the bpf_*_storage_delete()
helper and the map_delete_elem() syscall. Note that "delete" elem
before the owner's (sk/task/cgrp/inode) lifetime ended is not
the common usage for the local storage.
The common free path, bpf_local_storage_destroy(), can reuse the
memory immediately. This common path means the storage stays with
its owner until the owner is destroyed.
The above mentioned "delete" elem paths that cannot
reuse immediately always has the 'use_trace_rcu == true'.
The cases that is safe for immediate reuse always have
'use_trace_rcu == false'. Instead of adding another arg
in a later patch, this patch re-purpose this arg
to reuse_now and have the test logic reversed.
In a later patch, 'reuse_now == true' will free to the
bpf_mem_cache_free() where the memory can be reused
immediately. 'reuse_now == false' will go through the
call_rcu_tasks_trace().
Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org>
Link: https://lore.kernel.org/r/20230308065936.1550103-7-martin.lau@linux.dev
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
This patch remembers which smap triggers the allocation
of a 'struct bpf_local_storage' object. The local_storage is
allocated during the very first selem added to the owner.
The smap pointer is needed when using the bpf_mem_cache_free
in a later patch because it needs to free to the correct
smap's bpf_mem_alloc object.
When a selem is being removed, it needs to check if it is
the selem that triggers the creation of the local_storage.
If it is, the local_storage->smap pointer will be reset to NULL.
This NULL reset is done under the local_storage->lock in
bpf_selem_unlink_storage_nolock() when a selem is being removed.
Also note that the local_storage may not go away even
local_storage->smap is NULL because there may be other
selem still stored in the local_storage.
Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org>
Link: https://lore.kernel.org/r/20230308065936.1550103-6-martin.lau@linux.dev
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
This patch first renames bpf_local_storage_unlink_nolock to
bpf_local_storage_destroy(). It better reflects that it is only
used when the storage's owner (sk/task/cgrp/inode) is being kfree().
All bpf_local_storage_destroy's caller is taking the spin lock and
then free the storage. This patch also moves these two steps into
the bpf_local_storage_destroy.
This is a preparation work for a later patch that uses
bpf_mem_cache_alloc/free in the bpf_local_storage.
Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org>
Link: https://lore.kernel.org/r/20230308065936.1550103-3-martin.lau@linux.dev
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
This patch moves the bpf_local_storage_free_rcu() and
bpf_selem_unlink_map() to static because they are
not used outside of bpf_local_storage.c.
Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org>
Link: https://lore.kernel.org/r/20230308065936.1550103-2-martin.lau@linux.dev
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
There is quite a bit of tribal knowledge around proper use of try_module_get()
and requiring *somehow* the module to still exist to use this call in a way
that is safe. Document this bit of tribal knowledge. To be clear, you should
only use try_module_get() *iff* you are 100% sure the module already does
exist and is not on its way out.
You can be sure the module still exists and is alive through:
1) Direct protection with its refcount: you know some earlier caller called
__module_get() safely
2) Implied protection: there is an implied protection against module removal
Having an idea of when you are sure __module_get() might be called earlier is
easy to understand however the implied protection requires an example. We use
sysfs an an example for implied protection without a direct module reference
count bump. kernfs / sysfs uses its own internal reference counting for files
being actively used, when such file are active they completely prevent
the module from being removed. kernfs protects this with its kernfs_active().
Effort has been put into verifying the kernfs implied protection works by
using a currently out-of-tree test_sysfs selftest test #32 [0]:
./tools/testing/selftests/sysfs/sysfs.sh -t 0032
Without kernfs / sysfs preventing module removal through its active reference
count (kernfs_active()) the write would fail or worse, a crash would happen in
this test and it does not.
Similar safeguards are required for other users of try_module_get() *iff*
they are not ensuring the above rule 1) is followed.
[0] https://lore.kernel.org/lkml/20211029184500.2821444-4-mcgrof@kernel.org/
Signed-off-by: Luis Chamberlain <mcgrof@kernel.org>
|
|
Fix the nid_t field so that its size is correctly reported in the text
format embedded in trace.dat files. As it stands, it is reported as
being of size 4:
field:nid_t nid[3]; offset:24; size:4; signed:0;
Instead of 12:
field:nid_t nid[3]; offset:24; size:12; signed:0;
This also fixes the reported offset of subsequent fields so that they
match with the actual struct layout.
Signed-off-by: Douglas Raillard <douglas.raillard@arm.com>
Reviewed-by: Mukesh Ojha <quic_mojha@quicinc.com>
Reviewed-by: Chao Yu <chao@kernel.org>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
|
