| Age | Commit message (Collapse) | Author |
|---|
|
IO operations may be needed before md_run(), such as updating metadata
after writing sysfs. Without bioset, this triggers a NULL pointer
dereference as below:
BUG: kernel NULL pointer dereference, address: 0000000000000020
Call Trace:
md_update_sb+0x658/0xe00
new_level_store+0xc5/0x120
md_attr_store+0xc9/0x1e0
sysfs_kf_write+0x6f/0xa0
kernfs_fop_write_iter+0x141/0x2a0
vfs_write+0x1fc/0x5a0
ksys_write+0x79/0x180
__x64_sys_write+0x1d/0x30
x64_sys_call+0x2818/0x2880
do_syscall_64+0xa9/0x580
entry_SYSCALL_64_after_hwframe+0x4b/0x53
Reproducer
```
mdadm -CR /dev/md0 -l1 -n2 /dev/sd[cd]
echo inactive > /sys/block/md0/md/array_state
echo 10 > /sys/block/md0/md/new_level
```
mddev_init() can only be called once per mddev, no need to test if bioset
has been initialized anymore.
Link: https://lore.kernel.org/linux-raid/20251103125757.1405796-3-linan666@huaweicloud.com
Fixes: d981ed841930 ("md: Add new_level sysfs interface")
Signed-off-by: Li Nan <linan122@huawei.com>
Reviewed-by: Xiao Ni <xni@redhat.com>
Signed-off-by: Yu Kuai <yukuai@fnnas.com>
|
|
'md_redundancy_group' are created in md_run() and deleted in del_gendisk(),
but these are not paired. Writing inactive/active to sysfs array_state can
trigger md_run() multiple times without del_gendisk(), leading to
duplicate creation as below:
sysfs: cannot create duplicate filename '/devices/virtual/block/md0/md/sync_action'
Call Trace:
dump_stack_lvl+0x9f/0x120
dump_stack+0x14/0x20
sysfs_warn_dup+0x96/0xc0
sysfs_add_file_mode_ns+0x19c/0x1b0
internal_create_group+0x213/0x830
sysfs_create_group+0x17/0x20
md_run+0x856/0xe60
? __x64_sys_openat+0x23/0x30
do_md_run+0x26/0x1d0
array_state_store+0x559/0x760
md_attr_store+0xc9/0x1e0
sysfs_kf_write+0x6f/0xa0
kernfs_fop_write_iter+0x141/0x2a0
vfs_write+0x1fc/0x5a0
ksys_write+0x79/0x180
__x64_sys_write+0x1d/0x30
x64_sys_call+0x2818/0x2880
do_syscall_64+0xa9/0x580
entry_SYSCALL_64_after_hwframe+0x4b/0x53
md: cannot register extra attributes for md0
Creation of it depends on 'pers', its lifecycle cannot be aligned with
gendisk. So fix this issue by triggering 'md_redundancy_group' deletion
when the array is becoming inactive.
Link: https://lore.kernel.org/linux-raid/20251103125757.1405796-2-linan666@huaweicloud.com
Fixes: 790abe4d77af ("md: remove/add redundancy group only in level change")
Signed-off-by: Li Nan <linan122@huawei.com>
Reviewed-by: Xiao Ni <xni@redhat.com>
Signed-off-by: Yu Kuai <yukuai@fnnas.com>
|
|
When adding a disk to a md array, avoid updating the array's
logical_block_size to match the new disk. This prevents accidental
partition table loss that renders the array unusable.
The later patch will introduce a way to configure the array's
logical_block_size.
The issue was introduced before Linux 2.6.12-rc2.
Link: https://lore.kernel.org/linux-raid/20250918115759.334067-2-linan666@huaweicloud.com/
Fixes: d2e45eace8 ("[PATCH] Fix raid "bio too big" failures")
Signed-off-by: Li Nan <linan122@huawei.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Yu Kuai <yukuai@fnnas.com>
|
|
Use new helper fixed_phy_register_100fd to simplify the code.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://patch.msgid.link/922f1b45-1748-4dd2-87eb-9d018df44731@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Fix a possible leak in mdiobus_register_device() when both a
reset-gpio and a reset-controller are present.
Clean up the already claimed reset-gpio, when the registration of
the reset-controller fails, so when an error code is returned, the
device retains its state before the registration attempt.
Link: https://lore.kernel.org/all/20251106144603.39053c81@kernel.org/
Fixes: 71dd6c0dff51 ("net: phy: add support for reset-controller")
Signed-off-by: Buday Csaba <buday.csaba@prolan.hu>
Link: https://patch.msgid.link/4b419377f8dd7d2f63f919d0f74a336c734f8fff.1762584481.git.buday.csaba@prolan.hu
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Currently if a user enqueues a work item using schedule_delayed_work() the
used wq is "system_wq" (per-cpu wq) while queue_delayed_work() use
WORK_CPU_UNBOUND (used when a cpu is not specified). The same applies to
schedule_work() that is using system_wq and queue_work(), that makes use
again of WORK_CPU_UNBOUND.
This lack of consistency cannot be addressed without refactoring the API.
alloc_workqueue() treats all queues as per-CPU by default, while unbound
workqueues must opt-in via WQ_UNBOUND.
This default is suboptimal: most workloads benefit from unbound queues,
allowing the scheduler to place worker threads where they’re needed and
reducing noise when CPUs are isolated.
This continues the effort to refactor workqueue APIs, which began with
the introduction of new workqueues and a new alloc_workqueue flag in:
commit 128ea9f6ccfb ("workqueue: Add system_percpu_wq and system_dfl_wq")
commit 930c2ea566af ("workqueue: Add new WQ_PERCPU flag")
This change adds a new WQ_PERCPU flag to explicitly request
alloc_workqueue() to be per-cpu when WQ_UNBOUND has not been specified.
With the introduction of the WQ_PERCPU flag (equivalent to !WQ_UNBOUND),
any alloc_workqueue() caller that doesn’t explicitly specify WQ_UNBOUND
must now use WQ_PERCPU.
Once migration is complete, WQ_UNBOUND can be removed and unbound will
become the implicit default.
Suggested-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Marco Crivellari <marco.crivellari@suse.com>
Link: https://patch.msgid.link/20251107134452.198378-1-marco.crivellari@suse.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The "->allstasleep" variable is a 1 bit bitfield. It can only be 0 or 1.
This "= -1" assignement should be "= 0" as other chips and vendor driver.
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Closes: https://lore.kernel.org/linux-wireless/5c992936-4e7b-4c0a-abfc-0ec0fb9ef9fd@suswa.mountain/T/#t
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/1762390172-21091-1-git-send-email-pkshih@realtek.com
|
|
Tested in station mode and a little in AP mode.
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/180a5e77-9297-4ffc-80d5-191dfef47661@gmail.com
|
|
This is the entry point of the new rtw89_8852au module.
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/9580e5be-2bd1-45f9-ab75-616b86e25694@gmail.com
|
|
Make rtw8852a_read_efuse() accept USB devices and load the MAC
address from the correct offset.
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/97412e2c-ac98-403c-9056-9d9fe1ed9f28@gmail.com
|
|
"hfc" means "hci fc" which is "Host Control Interface Flow Control".
These are some parameters needed for RTL8852AU.
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/d1032888-2a53-4c52-a8b9-6e00cd6758dc@gmail.com
|
|
Add rtw8852a_dle_mem_usb and its various quotas and sizes in struct
rtw89_mac_size_set.
"dle" could be "Data Link Engine" or "Double Link Engine". These are
some parameters needed for RTL8852AU.
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/d0a09039-97a8-4501-b023-510c126d8c61@gmail.com
|
|
The am65_cpsw_iet_verify_wait() function attempts verification 20 times,
toggling the AM65_CPSW_PN_IET_MAC_LINKFAIL bit in each iteration. When
the LINKFAIL bit transitions from 1 to 0, the MAC merge layer initiates
the verification process and waits for the timeout configured in
MAC_VERIFY_CNT before automatically retransmitting. The MAC_VERIFY_CNT
register is configured according to the user-defined verify/response
timeout in am65_cpsw_iet_set_verify_timeout_count(). As per IEEE 802.3
Clause 99, the hardware performs this automatic retry up to 3 times.
Current implementation toggles LINKFAIL after the user-configured
verify/response timeout in each iteration, forcing the hardware to
restart verification instead of respecting the MAC_VERIFY_CNT timeout.
This bypasses the hardware's automatic retry mechanism.
Fix this by moving the LINKFAIL bit toggle outside the retry loop and
reducing the retry count from 20 to 3. The software now only monitors
the status register while the hardware autonomously handles the 3
verification attempts at proper MAC_VERIFY_CNT intervals.
Fixes: 49a2eb9068246 ("net: ethernet: ti: am65-cpsw-qos: Add Frame Preemption MAC Merge support")
Signed-off-by: Aksh Garg <a-garg7@ti.com>
Link: https://patch.msgid.link/20251106092305.1437347-3-a-garg7@ti.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The CPSW module uses the MAC_VERIFY_CNT bit field in the
CPSW_PN_IET_VERIFY_REG_k register to set the verify/response timeout
count. This register specifies the number of clock cycles to wait before
resending a verify packet if the verification fails.
The verify/response timeout count, as being set by the function
am65_cpsw_iet_set_verify_timeout_count() is hardcoded for 125MHz
clock frequency, which varies based on PHY mode and link speed.
The respective clock frequencies are as follows:
- RGMII mode:
* 1000 Mbps: 125 MHz
* 100 Mbps: 25 MHz
* 10 Mbps: 2.5 MHz
- QSGMII/SGMII mode: 125 MHz (all speeds)
Fix this by adding logic to calculate the correct timeout counts
based on the actual PHY interface mode and link speed.
Fixes: 49a2eb9068246 ("net: ethernet: ti: am65-cpsw-qos: Add Frame Preemption MAC Merge support")
Signed-off-by: Aksh Garg <a-garg7@ti.com>
Link: https://patch.msgid.link/20251106092305.1437347-2-a-garg7@ti.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Make rtw89_mac_pwr_seq() select the right parts of the power sequences
based on the interface type.
This is only relevant for RTL8852A. The other chips don't use power
sequences.
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/dec13310-06eb-429e-acb8-4c5b62656836@gmail.com
|
|
netif_carrier_ok() doesn't check if the slave is up. Before the below
commit, netif_running() was also checked.
Fixes: 23a6037ce76c ("bonding: Remove support for use_carrier")
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Acked-by: Jay Vosburgh <jv@jvosburgh.net>
Link: https://patch.msgid.link/20251106180252.3974772-1-nicolas.dichtel@6wind.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Change the driver's default behavior to prefer the largest available RX
buffer length supported by the device for DQO format, rather than always
using the hardcoded 2K default.
Previously, the driver would initialize with
`GVE_DEFAULT_RX_BUFFER_SIZE` (2K), even if the device advertised support
for a larger length (e.g., 4K).
Performance observations:
- With LRO disabled, we observed >10% improvement in RX single stream
throughput when MTU >=2048.
- With LRO enabled, we observed >10% improvement in RX single stream
throughput when MTU >=1460.
- No regressions were observed.
Signed-off-by: Ankit Garg <nktgrg@google.com>
Reviewed-by: Harshitha Ramamurthy <hramamurthy@google.com>
Reviewed-by: Jordan Rhee <jordanrhee@google.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Joshua Washington <joshwash@google.com>
Link: https://patch.msgid.link/20251106192746.243525-5-joshwash@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add support for getting and setting the RX buffer length via the
ethtool ring parameters (`ethtool -g`/`-G`). The driver restricts the
allowed buffer length to 2048 (SZ_2K) by default and allows 4096 (SZ_4K)
based on device options.
As XDP is only supported when the `rx_buf_len` is 2048, the driver now
enforces this in two places:
1. In `gve_xdp_set`, rejecting XDP programs if the current buffer
length is not 2048.
2. In `gve_set_rx_buf_len_config`, rejecting buffer length changes if XDP
is loaded and the new length is not 2048.
Signed-off-by: Ankit Garg <nktgrg@google.com>
Reviewed-by: Harshitha Ramamurthy <hramamurthy@google.com>
Reviewed-by: Jordan Rhee <jordanrhee@google.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Joshua Washington <joshwash@google.com>
Link: https://patch.msgid.link/20251106192746.243525-4-joshwash@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Plumb extack as it allows us to send more detailed error messages back
and append 'gve' suffix to method name per convention.
NL_SET_ERR_MSG_FMT_MOD doesn't support format string longer than 80
chars so keeping netdev warning with actual queue count details.
Signed-off-by: Ankit Garg <nktgrg@google.com>
Reviewed-by: Harshitha Ramamurthy <hramamurthy@google.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Joshua Washington <joshwash@google.com>
Link: https://patch.msgid.link/20251106192746.243525-3-joshwash@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Previously, enabling header split via `gve_set_hsplit_config` also
implicitly changed the RX buffer length to 4K (if supported by the
device). This coupled two settings that should be orthogonal; this patch
removes that side effect.
After this change, `gve_set_hsplit_config` only toggles the header
split configuration. The RX buffer length is no longer affected and
must be configured independently.
Signed-off-by: Ankit Garg <nktgrg@google.com>
Reviewed-by: Harshitha Ramamurthy <hramamurthy@google.com>
Reviewed-by: Jordan Rhee <jordanrhee@google.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Joshua Washington <joshwash@google.com>
Link: https://patch.msgid.link/20251106192746.243525-2-joshwash@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Rather than placing the phy_intf_sel() setup in the ->init() method,
move it to the new ->set_phy_intf_sel() method.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1vHHqY-0000000Djrn-1D6H@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
It no longer makes sense to pass a pointer to struct
plat_stmmacenet_data when calling the set_mode() methods to only use it
to get a pointer to the ingenic_mac structure that we already had in
the caller. Simplify this by passing the struct ingenic_mac pointer.
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1vHHqT-0000000Djrh-0ka3@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
As per the previous commit, we have validated that the phy_intf_sel
value is one that is permissible for this SoC, so there is no need to
handle invalid PHY interface modes. We can also apply the other
configuration based upon the phy_intf_sel value rather than the
PHY interface mode.
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1vHHqO-0000000Djrb-0DPN@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
x1000, x1600 and x1830 only accept RMII mode. PHY_INTF_SEL_RMII is only
selected with PHY_INTERFACE_MODE_RMII, and PHY_INTF_SEL_RMII has been
validated by the SoC's .valid_phy_intf_sel bitmask. Thus, checking the
interface mode in these functions becomes unnecessary. Remove these.
jz4775 is similar, except for a greater set of PHY_INTF_SEL_x valies.
Also remove the switch statement here.
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1vHHqI-0000000DjrV-3ygL@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Move the printing of the MAC PHY control register interface mode
setting into ingenic_set_phy_intf_sel(), and use phy_modes() to
print the string rather than using the enum name.
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1vHHqD-0000000DjrP-3aaU@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Use stmmac_get_phy_intf_sel() to decode the PHY interface mode to the
phy_intf_sel value, validate the result against the SoC specific
supported phy_intf_sel values, and pass into the SoC specific
set_mode() methods, replacing the local phy_intf_sel variable. This
provides the value for the MACPHYC_PHY_INFT_MASK field.
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1vHHq8-0000000DjrJ-2NRK@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Move the preparation of the PHY_INTF_SEL_x bitfield out of the switch()
statement such that it only appears once.
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1vHHq3-0000000DjrD-1u8O@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Use the PHY_INTF_SEL_x values directly in each of the mac_set_mode
methods rather than the driver private MACPHYC_PHY_INFT_x definitions.
Remove the MACPHYC_PHY_INFT_x definitions.
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1vHHpy-0000000Djr7-1R1m@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Use the common dwmac definitions for the PHY interface selection field.
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1vHHpt-0000000Djr1-0wwr@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
All paths configure the transmit clock as an input. Move this out of
the switch() statement to simplify the code.
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1vHHpo-0000000Djqv-0RD4@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Move ingenic_mac_init() to between variant specific set_mode()
implementations and ingenic_mac_probe(). No code changes.
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1vHHpi-0000000Djqp-4910@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In the current implementation, usbnet uses a fixed tx_qlen of:
USB2: 60 * 1518 bytes = 91.08 KB
USB3: 60 * 5 * 1518 bytes = 454.80 KB
Such large transmit queues can be problematic, especially for cellular
modems. For example, with a typical celluar link speed of 10 Mbit/s, a
fully occupied USB3 transmit queue results in:
454.80 KB / (10 Mbit/s / 8 bit/byte) = 363.84 ms
of additional latency.
This patch adds support for Byte Queue Limits (BQL) [1] to dynamically
manage the transmit queue size and reduce latency without sacrificing
throughput.
Testing was performed on various devices using the usbnet driver for
packet transmission:
- DELOCK 66045: USB3 to 2.5 GbE adapter (ax88179_178a)
- DELOCK 61969: USB2 to 1 GbE adapter (asix)
- Quectel RM520: 5G modem (qmi_wwan)
- USB2 Android tethering (cdc_ncm)
No performance degradation was observed for iperf3 TCP or UDP traffic,
while latency for a prioritized ping application was significantly
reduced. For example, using the USB3 to 2.5 GbE adapter, which was fully
utilized by iperf3 UDP traffic, the prioritized ping was improved from
1.6 ms to 0.6 ms. With the same setup but with a 100 Mbit/s Ethernet
connection, the prioritized ping was improved from 35 ms to 5 ms.
[1] https://lwn.net/Articles/469652/
Signed-off-by: Simon Schippers <simon.schippers@tu-dortmund.de>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://patch.msgid.link/20251106175615.26948-1-simon.schippers@tu-dortmund.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Using num_online_cpus() to report number of queues is actually not
correct, as reported by Michael[1].
netif_get_num_default_rss_queues() was used to replace num_online_cpus()
in the past, but tg3 ethtool callbacks didn't get converted. Doing it
now.
Link: https://lore.kernel.org/all/CACKFLim7ruspmqvjr6bNRq5Z_XXVk3vVaLZOons7kMCzsEG23A@mail.gmail.com/#t [1]
Signed-off-by: Breno Leitao <leitao@debian.org>
Suggested-by: Michael Chan <michael.chan@broadcom.com>
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Link: https://patch.msgid.link/20251107-tg3_counts-v1-1-337fe5c8ccb7@debian.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The ARL registers of BCM63XX embedded switches are somewhat unique. The
normal ARL table access registers have the same format as BCM5389, but
the ARL search registers differ:
* SRCH_CTL is at the same offset of BCM5389, but 16 bits wide. It does
not have more fields, just needs to be accessed by a 16 bit read.
* SRCH_RSLT_MACVID and SRCH_RSLT are aligned to 32 bit, and have shifted
offsets.
* SRCH_RSLT has a different format than the normal ARL data entry
register.
* There is only one set of ENTRY_N registers, implying a 1 bin layout.
So add appropriate ops for bcm63xx and let it use it.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20251107080749.26936-9-jonas.gorski@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
BCM5389, BCM5397 and BCM5398 use a different ARL entry format with just
a 16 bit fwdentry register, as well as different search control and data
offsets.
So add appropriate ops for them and switch those chips to use them.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20251107080749.26936-8-jonas.gorski@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Now that the differences in ARL entry formats are neatly contained into
functions per chip family, wrap them into an ops struct and add wrapper
functions to access them.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20251107080749.26936-7-jonas.gorski@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Split reading search entries into a function for each format.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20251107080749.26936-6-jonas.gorski@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In order to more easily support more formats, move accessing
ARL_SRCH_CTL into helper functions to contain the differences.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20251107080749.26936-5-jonas.gorski@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Move writing ARL entries into individual functions for each format.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20251107080749.26936-4-jonas.gorski@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Instead of duplicating the whole code iterating over all bins for
BCM5325, factor out reading and parsing the entry into its own
functions, and name it the modern one after the first chip with that ARL
format, (BCM53)95.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20251107080749.26936-3-jonas.gorski@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Align the b53_arl_read{,25}() functions by consistently using the
parsed arl entry instead of parsing the raw registers again.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20251107080749.26936-2-jonas.gorski@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
ie31200_register_mci() calls device_initialize() for priv->dev
unconditionally. However, in the error path, put_device() is not
called, leading to an imbalance. Similarly, in the unload path,
put_device() is missing.
Although edac_mc_free() eventually frees the memory, it does not
release the device initialized by device_initialize(). For code
readability and proper pairing of device_initialize()/put_device(),
add put_device() calls in both error and unload paths.
Found by code review.
Signed-off-by: Ma Ke <make24@iscas.ac.cn>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Reviewed-by: Qiuxu Zhuo <qiuxu.zhuo@intel.com>
Link: https://patch.msgid.link/20251106084735.35017-1-make24@iscas.ac.cn
|
|
Driver's probe function matches against driver's of_device_id table,
where each entry has non-NULL match data, so of_match_node() can be
simplified with of_device_get_match_data().
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
[sboyd@kernel.org: Use device_get_match_data() instead, drop
printk noise]
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
When converting the Renesas network drivers to use flags from enum
hwtstamp_rx_filters to control when to timestamp packages instead of a
driver specific schema with bit-wise flags an error was made.
The bit-wise driver specific flags correct logic to set get_ts was:
q: RAVB_BE + tstamp_rx_ctrl: 0 => 0
q: RAVB_NC + tstamp_rx_ctrl: 0 => 0
q: RAVB_BE + tstamp_rx_ctrl: RAVB_RXTSTAMP_TYPE_V2_L2_EVENT => 0
q: RAVB_NC + tstamp_rx_ctrl: RAVB_RXTSTAMP_TYPE_V2_L2_EVENT => 1
q: RAVB_BE + tstamp_rx_ctrl: RAVB_RXTSTAMP_TYPE_ALL => 1
q: RAVB_NC + tstamp_rx_ctrl: RAVB_RXTSTAMP_TYPE_ALL => 1
The converted logic to use enum flags mapped tstamp_rx_ctrl as
0 to HWTSTAMP_FILTER_NONE
RAVB_RXTSTAMP_TYPE_V2_L2_EVENT to HWTSTAMP_FILTER_PTP_V2_L2_EVENT
RAVB_RXTSTAMP_TYPE_ALL to HWTSTAMP_FILTER_ALL
But the logic was incorrectly changed to:
q: RAVB_BE + tstamp_rx_ctrl: HWTSTAMP_FILTER_NONE => 1 (error)
q: RAVB_NC + tstamp_rx_ctrl: HWTSTAMP_FILTER_NONE => 0
q: RAVB_BE + tstamp_rx_ctrl: HWTSTAMP_FILTER_PTP_V2_L2_EVENT => 0
q: RAVB_NC + tstamp_rx_ctrl: HWTSTAMP_FILTER_PTP_V2_L2_EVENT => 1
q: RAVB_BE + tstamp_rx_ctrl: HWTSTAMP_FILTER_ALL => 1
q: RAVB_NC + tstamp_rx_ctrl: HWTSTAMP_FILTER_ALL => 0 (error)
This change restores the converted flag check to the correct logic of
the bit-wise driver specific flags.
Reported-by: Simon Horman <horms@kernel.org>
Closes: https://lore.kernel.org/linux-renesas-soc/aQ4xSv9629XF-Bt3@horms.kernel.org/
Fixes: 16e2e6cf75e6 ("net: ravb: Use common defines for time stamping control")
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://patch.msgid.link/20251107200100.3637869-1-niklas.soderlund+renesas@ragnatech.se
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Commit e871abcda3b6 ("random: handle creditable entropy from atomic
process context") added the use of workqueues, which meant testing
whether the workqueue is valid, but it did not remove the existing check
of whether static keys have been initialized. This static key check is
unnecessary because workqueues are initialized long after it. And
semantically it doesn't make much sense either, because it's not really
directly calling a static key function in the condition.
Remove the now unnecessary check.
Signed-off-by: Thomas Weißschuh <thomas.weissschuh@linutronix.de>
[Jason: rewrite commit message with different explanation, rebase on
random.git, and update code comment.]
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
|
|
Add a comment to ptp_ocp_tty_show() explaining that the sysfs output
intentionally does not include a trailing newline. This is required for
backward compatibility with existing userspace software that reads the
sysfs attribute and uses the value directly as a device path.
A previous attempt to add a newline to align with common kernel
conventions broke userspace applications that were opening device paths
like "/dev/ttyS4\n" instead of "/dev/ttyS4", resulting in ENOENT errors.
This comment prevents future attempts to "fix" this behavior, which would
break existing userspace applications.
Link: https://lore.kernel.org/netdev/20251030124519.1828058-1-zhongqiu.han@oss.qualcomm.com/
Link: https://lore.kernel.org/netdev/aef3b850-5f38-4c28-a018-3b0006dc2f08@linux.dev/
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Zhongqiu Han <zhongqiu.han@oss.qualcomm.com>
Reviewed-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Link: https://patch.msgid.link/20251107074533.416048-1-zhongqiu.han@oss.qualcomm.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add all the required entry to add suppot for Airoha AN7583 PINs.
Where possible the same function group are used from Airoha EN7581 to
reduce code duplication.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The PWM GPIO struct definition follow the same pattern for every GPIO
pin hence it can be converted to a macro.
Create 2 macro one for normal mux and one for ext mux and convert all
the entry to these new macro to reduce code size.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
PHY LED GPIO pinctrl struct definition is very similar across the
different 4 PHY and 2 LED and it can be generelized to a macro.
To reduce code size, convert them to a common macro.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
In preparation for support of Airoha AN7583, generalize
pins/group/function/confs handling and move them in match_data.
Inner function will base the values on the pinctrl priv struct instead of
relying on hardcoded struct.
This permits to use different PIN data while keeping the same logic.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
