| Age | Commit message (Collapse) | Author |
|---|
|
To initialize the taprio block in lan966x, it is required to configure
the register REVISIT_DLY. The purpose of this register is to set the
delay before revisit the next gate and the value of this register depends
on the system clock. The problem is that the we calculated wrong the value
of the system clock period in picoseconds. The actual system clock is
~165.617754MHZ and this correspond to a period of 6038 pico seconds and
not 15125 as currently set.
Fixes: e462b2717380b4 ("net: lan966x: Add offload support for taprio")
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20251121061411.810571-1-horatiu.vultur@microchip.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
While we want to refactor intel_clock_gating.[ch] and likely move a lot
of display related code to display, start off with a little intermediate
change to use struct drm_device in the interface instead of struct
drm_i915_private, to allow us to drop another dependency on i915_drv.h
and struct drm_i915_private.
Cc: Luca Coelho <luciano.coelho@intel.com>
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Link: https://patch.msgid.link/20251121112200.3435099-2-jani.nikula@intel.com
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
intel_cdclk.c no longer needs i915_drv.h. Drop it.
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Link: https://patch.msgid.link/20251121112200.3435099-1-jani.nikula@intel.com
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
The ASP chip is a very old variant of the GSP chip and is used e.g. in
HP 730 workstations. When trying to reprogram the affinity it will crash
with a HPMC as the relevant registers don't seem to be at the usual
location. Let's avoid the crash by checking the sversion. Also note,
that reprogramming isn't necessary either, as the HP730 is a just a
single-CPU machine.
Signed-off-by: Helge Deller <deller@gmx.de>
Cc: stable@vger.kernel.org
|
|
Since increase_top() does it's own READ_ONCE() on top_of_table, the
caller's prior READ_ONCE() could be inconsistent and the first time
through the loop we may actually already have the right level if two
threads are racing map.
In this case new_level will be left uninitialized.
Further all the exits from the loop have to either commit to the new top
or free any memory allocated so the early return must be a goto err_free.
Make it so the only break from the loop always sets new_level to the right
value and all other exits go to err_free. Use pts.level (the pts
represents the top we are stacking) within the loop instead of new_level.
Fixes: dcd6a011a8d5 ("iommupt: Add map_pages op")
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Closes: https://lore.kernel.org/r/aRwgNW9PiW2j-Qwo@stanley.mountain
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Reviewed-by: Alejandro Jimenez <alejandro.j.jimenez@oracle.com>
Reviewed-by: Vasant Hegde <vasant.hegde@amd.com>
Reviewed-by: Kevin Tian <kevin.tian@intel.com>
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
|
|
modify_irte_ga()
The return type of __modify_irte_ga() is int, but modify_irte_ga()
treats it as a bool. Casting the int to bool discards the error code.
To fix the issue, change the type of ret to int in modify_irte_ga().
Fixes: 57cdb720eaa5 ("iommu/amd: Do not flush IRTE when only updating isRun and destination fields")
Cc: stable@vger.kernel.org
Signed-off-by: Jinhui Guo <guojinhui.liam@bytedance.com>
Reviewed-by: Vasant Hegde <vasant.hegde@amd.com>
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
|
|
Having the host bridge allocation inside pci_host_common_init() results
in a lot of complexity in the pcie-apple driver (the only direct user
of this function outside of core PCI code).
It forces the allocation of driver-specific tracking structures outside
of the bridge allocation, which in turn requires it to use inefficient
data structures to match the bridge and the private structure as needed.
Instead, let the bridge structure be passed to pci_host_common_init(),
allowing the driver to allocate it together with the private data,
as it is usually intended. The driver can then retrieve the bridge
via the owning device attached to the PCI config window structure.
This allows the pcie-apple driver to be significantly simplified.
Both core and driver code are changed in one go to avoid going via
a transitional interface.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Reviewed-by: Radu Rendec <rrendec@redhat.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Manivannan Sadhasivam <mani@kernel.org>
Cc: Rob Herring <robh@kernel.org>
Cc: Krzysztof Wilczyński <kwilczynski@kernel.org>
Cc: Lorenzo Pieralisi <lpieralisi@kernel.org>
Link: https://lore.kernel.org/r/86jyzms036.wl-maz@kernel.org
Link: https://patch.msgid.link/20251125102726.865617-1-maz@kernel.org
|
|
Revert commit fbd401e95e56 ("ACPI: processor: idle: Redefine two
functions as void") because it depends on a problematic one.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/mediatek/linux into soc/drivers
MediaTek soc driver updates
This adds socinfo entries for MT8189 Kompanio 540, an extra entry
for a variant of MT8391 (AV/AZA) Genio 720 SoC, and support for
the PMIC Wrapper (by adding a compatible string) in MT8189.
* tag 'mtk-soc-for-v6.19' of https://git.kernel.org/pub/scm/linux/kernel/git/mediatek/linux:
dt-bindings: soc: mediatek: pwrap: Add compatible for MT8189 SoC
soc: mediatek: mtk-socinfo: Add entry for MT8391AV/AZA Genio 720
soc: mediatek: mtk-socinfo: Add extra entry for MT8189
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
A stray and unneeded semicolon was added here by accident, just drop
it.
Fixes: ee19b52c31b3 ("mfd: sec: Use chained IRQs for s2mpg10")
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202511230909.zk7EkTnb-lkp@intel.com/
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://patch.msgid.link/20251124-s2mpg10-chained-irq-semicolon-v1-1-578ba2d7adca@linaro.org
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
Revert commit 559f2eacc8a2 ACPI: processor: Do not expose global variable
acpi_idle_driver" because it depends on a problematic one.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/pinctrl/intel into devel
intel-pinctrl for v6.19-1
* Add and use common macro INTEL_GPP() to avoid duplication
* Export intel_gpio_add_pin_ranges() and reuse it instead of custom copies
* Unify error messages with help of dev_err_probe()
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
When compile-testing for UM-Linux the build fails because
we don't have IOMEM.
Add an explicit dependency.
Fixes: 920500c5fe66 ("pinctrl: cix: Add pin-controller support for sky1")
Reviewed-by: Peter Chen <peter.chen@cixtech.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The selective fetch code doesn't handle asycn flips correctly.
There is a nonsense check for async flips in
intel_psr2_sel_fetch_config_valid() but that only gets called
for modesets/fastsets and thus does nothing for async flips.
Currently intel_async_flip_check_hw() is very unhappy as the
selective fetch code pulls in planes that are not even async
flips capable.
Reject async flips when selective fetch is enabled, until
someone fixes this properly (ie. disable selective fetch while
async flips are being issued).
Cc: stable@vger.kernel.org
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patch.msgid.link/20251105171015.22234-1-ville.syrjala@linux.intel.com
Reviewed-by: Jouni Högander <jouni.hogander@intel.com>
(cherry picked from commit a5f0cc8e0cd4007370af6985cb152001310cf20c)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
|
|
soc/drivers
Reset controller updates for v6.19
* Add support for LAN969x, eic770 and RZ/G3S reset controllers,
for the RZ/G3S USB-PHY reset controller, and for the remaining
TH1520 reset controllers.
* Drop legacy reset control lookup code.
* Include linux/bits.h from linux/reset.h to make it self-contained.
* tag 'reset-for-v6.19' of https://git.pengutronix.de/git/pza/linux:
Documentation: reset: Remove reset_controller_add_lookup()
reset: fix BIT macro reference
reset: rzg2l-usbphy-ctrl: Fix a NULL vs IS_ERR() bug in probe
reset: th1520: Support reset controllers in more subsystems
reset: th1520: Prepare for supporting multiple controllers
dt-bindings: reset: thead,th1520-reset: Add controllers for more subsys
dt-bindings: reset: thead,th1520-reset: Remove non-VO-subsystem resets
reset: remove legacy reset lookup code
clk: davinci: psc: drop unused reset lookup
reset: rzg2l-usbphy-ctrl: Add support for RZ/G3S SoC
reset: rzg2l-usbphy-ctrl: Add support for USB PWRRDY
dt-bindings: reset: renesas,rzg2l-usbphy-ctrl: Document RZ/G3S support
reset: eswin: Add eic7700 reset driver
dt-bindings: reset: eswin: Documentation for eic7700 SoC
reset: sparx5: add LAN969x support
dt-bindings: reset: microchip: Add LAN969x support
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Use the modern PM macros for the suspend and resume functions to be
automatically dropped by the compiler when CONFIG_PM or
CONFIG_PM_SLEEP are disabled, without having to use __maybe_unused
Signed-off-by: Jisheng Zhang <jszhang@kernel.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Link: https://lore.kernel.org/r/20251124002105.25429-15-jszhang@kernel.org
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
|
|
Use the modern PM macros for the suspend and resume functions to be
automatically dropped by the compiler when CONFIG_PM or
CONFIG_PM_SLEEP are disabled, without having to use __maybe_unused
Signed-off-by: Jisheng Zhang <jszhang@kernel.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Link: https://lore.kernel.org/r/20251124002105.25429-14-jszhang@kernel.org
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
|
|
Use the modern PM macros for the suspend and resume functions to be
automatically dropped by the compiler when CONFIG_PM or
CONFIG_PM_SLEEP are disabled, without having to use __maybe_unused
Signed-off-by: Jisheng Zhang <jszhang@kernel.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Link: https://lore.kernel.org/r/20251124002105.25429-13-jszhang@kernel.org
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
|
|
Use the modern PM macros for the suspend and resume functions to be
automatically dropped by the compiler when CONFIG_PM or
CONFIG_PM_SLEEP are disabled, without having to use __maybe_unused
Signed-off-by: Jisheng Zhang <jszhang@kernel.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Link: https://lore.kernel.org/r/20251124002105.25429-12-jszhang@kernel.org
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
|
|
Use the modern PM macros for the suspend and resume functions to be
automatically dropped by the compiler when CONFIG_PM or
CONFIG_PM_SLEEP are disabled, without having to use __maybe_unused
Signed-off-by: Jisheng Zhang <jszhang@kernel.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20251124002105.25429-11-jszhang@kernel.org
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
|
|
Use the modern PM macros for the suspend and resume functions to be
automatically dropped by the compiler when CONFIG_PM or
CONFIG_PM_SLEEP are disabled, without having to use __maybe_unused
Signed-off-by: Jisheng Zhang <jszhang@kernel.org>
Acked-by: Andy Shevchenko <andy@kernel.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Link: https://lore.kernel.org/r/20251124002105.25429-10-jszhang@kernel.org
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
|
|
Use the modern PM macros for the suspend and resume functions to be
automatically dropped by the compiler when CONFIG_PM or
CONFIG_PM_SLEEP are disabled, without having to use __maybe_unused
Signed-off-by: Jisheng Zhang <jszhang@kernel.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Link: https://lore.kernel.org/r/20251124002105.25429-9-jszhang@kernel.org
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
|
|
Use the modern PM macros for the suspend and resume functions to be
automatically dropped by the compiler when CONFIG_PM or
CONFIG_PM_SLEEP are disabled, without having to use __maybe_unused
Signed-off-by: Jisheng Zhang <jszhang@kernel.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Link: https://lore.kernel.org/r/20251124002105.25429-8-jszhang@kernel.org
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
|
|
Use the modern PM macros for the suspend and resume functions to be
automatically dropped by the compiler when CONFIG_PM or
CONFIG_PM_SLEEP are disabled, without having to use __maybe_unused
Signed-off-by: Jisheng Zhang <jszhang@kernel.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Link: https://lore.kernel.org/r/20251124002105.25429-7-jszhang@kernel.org
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
|
|
Use the modern PM macros for the suspend and resume functions to be
automatically dropped by the compiler when CONFIG_PM or
CONFIG_PM_SLEEP are disabled, without having to use __maybe_unused
Signed-off-by: Jisheng Zhang <jszhang@kernel.org>
Acked-by: Andy Shevchenko <andy@kernel.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Link: https://lore.kernel.org/r/20251124002105.25429-6-jszhang@kernel.org
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
|
|
Use the modern PM macros for the suspend and resume functions to be
automatically dropped by the compiler when CONFIG_PM or
CONFIG_PM_SLEEP are disabled, without having to use #ifdef guards.
This has the advantage of always compiling these functions in,
independently of any Kconfig option. Thanks to that, bugs and other
regressions are subsequently easier to catch.
The pl061_context_save_regs structure is always embedded into struct
pl061 to simplify code, so this brings a tiny 8 bytes memory overhead
for !CONFIG_PM_SLEEP.
Signed-off-by: Jisheng Zhang <jszhang@kernel.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Link: https://lore.kernel.org/r/20251124002105.25429-5-jszhang@kernel.org
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
|
|
Use the modern PM macros for the suspend and resume functions to be
automatically dropped by the compiler when CONFIG_PM or
CONFIG_PM_SLEEP are disabled, without having to use #ifdef guards.
This has the advantage of always compiling these functions in,
independently of any Kconfig option. Thanks to that, bugs and other
regressions are subsequently easier to catch.
Signed-off-by: Jisheng Zhang <jszhang@kernel.org>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Link: https://lore.kernel.org/r/20251124002105.25429-4-jszhang@kernel.org
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
|
|
Use the modern PM macros for the suspend and resume functions to be
automatically dropped by the compiler when CONFIG_PM or
CONFIG_PM_SLEEP are disabled, without having to use #ifdef guards.
This has the advantage of always compiling these functions in,
independently of any Kconfig option. Thanks to that, bugs and other
regressions are subsequently easier to catch.
Signed-off-by: Jisheng Zhang <jszhang@kernel.org>
Acked-by: Doug Berger <opendmb@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20251124002105.25429-3-jszhang@kernel.org
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
|
|
Use the modern PM macros for the suspend and resume functions to be
automatically dropped by the compiler when CONFIG_PM or
CONFIG_PM_SLEEP are disabled, without having to use #ifdef guards.
This has the advantage of always compiling these functions in,
independently of any Kconfig option. Thanks to that, bugs and other
regressions are subsequently easier to catch.
Signed-off-by: Jisheng Zhang <jszhang@kernel.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Link: https://lore.kernel.org/r/20251124002105.25429-2-jszhang@kernel.org
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32 into soc/drivers
STM32 Firewall bus for v6.19, round 1
Highlights:
----------
The STM32MP21x platforms have a slightly different RIFSC. Add support
for these platforms.
Also, the RIF is a complex firewall framework which can be tricky
to debug. To facilitate the latter, add a debugfs entry that can
be used to display the whole RIFSC firewall configuration at runtime.
* tag 'stm32-bus-firewall-for-v6.19-1' of git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32:
bus: rifsc: add debugfs entry to dump the firewall configuration
dt-bindings: bus: add stm32mp21 RIFSC compatible
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/andy/linux-gpio-intel into gpio/for-next
intel-gpio for v6.19-1
* Replace min_t() by min() to avoid cutting upper bits and do type checking
gpiolib: acpi: use min() instead of min_t()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into soc/drivers
Some additional sane defaults for the oldish rk3368 soc.
* tag 'v6.19-rockchip-drivers1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
soc: rockchip: grf: Add select correct PWM implementation on RK3368
soc: rockchip: grf: Set pwm2/xin32k pad default to xin32k for rk3368
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux into soc/drivers
Qualcomm driver updates for v6.19
Support for hardware-keymanager v1 support for wrapped keys is introduce
in the ICE driver.
Support for the new Kaanapali mobile platform is added to last-level
cache controller, pd-mapper, and UBWC drivers.
UBWC driver gains support for the Monaco and Glymur platforms.
The PMIC GLINK driver is extended to handle the differences found in
targets where the related firmware runs on the SoCCP.
Support for running on targets without initialized SMEM is provided, by
reworking the SMEM driver to differentiate between "not yet probed" and
"probed but there was no SMEM". An unwanted WARN_ON() that triggered if
clients asked for a SMEM item beyond the currently running system's
limit, was removed, to allow new use cases to gracefully fail on old
targets.
The Qualcomm socinfo driver is extended with support for version 20
through 23 and support for providing version information about more than
32 remote processors. Identifiers for QCS6490 and SM8850 are also added.
Additionally, a number of smaller bug fixes and cleanups in PBS, OCMEM,
GSBI, TZMEM, and MDT-loader are included.
* tag 'qcom-drivers-for-6.19' of https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux: (31 commits)
soc: qcom: mdt_loader: rename 'firmware' parameter of qcom_mdt_load()
soc: qcom: mdt_loader: merge __qcom_mdt_load() and qcom_mdt_load_no_init()
soc: qcom: socinfo: Add reserve field to support future extension
soc: qcom: socinfo: Add support for new fields in revision 20
dt-bindings: firmware: qcom,scm: Document SCM on Kaanapali SOC
soc: qcom: socinfo: add support to extract more than 32 image versions
soc: qcom: smem: drop the WARN_ON() on SMEM item validation
soc: qcom: ubwc: Add config for Kaanapali
soc: qcom: socinfo: Add SoC ID for QCS6490
dt-bindings: arm: qcom,ids: Add SoC ID for QCS6490
soc: qcom: ice: Add HWKM v1 support for wrapped keys
soc: qcom: smem: better track SMEM uninitialized state
err.h: add INIT_ERR_PTR() macro
soc: qcom: smem: fix hwspinlock resource leak in probe error paths
dt-bindings: soc: qcom,aoss-qmp: Document the Glymur AOSS side channel
dt-bindings: soc: qcom,aoss-qmp: Document the Kaanapali AOSS channel
soc: qcom: ubwc: Add QCS8300 UBWC cfg
dt-bindings: firmware: qcom,scm: Document Glymur scm
soc: qcom: socinfo: Add SM8850 SoC ID
dt-bindings: arm: qcom,ids: Add SoC ID for SM8850
...
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-omap into soc/drivers
ti-sysc: allow OMAP2 and OMAP4 timers to be reserved on AM33xx
* tag 'omap-for-v6.19/drivers-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-omap:
ti-sysc: allow OMAP2 and OMAP4 timers to be reserved on AM33xx
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Merge the mmc fixes for v6.18-rc[n] into the next branch, to allow them to
get tested together with the new mmc changes that are targeted for v6.19.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Add support for Awinic AW99706 backlight, which can be found in
tablet and notebook backlight, one case is the Lenovo Legion Y700
Gen4. This driver refers to the official datasheets and android
driver, they can be found in [1].
[1] https://www.awinic.com/en/productDetail/AW99706QNR
Signed-off-by: Junjie Cao <caojunjie650@gmail.com>
Tested-by: Pengyu Luo <mitltlatltl@gmail.com>
Signed-off-by: Pengyu Luo <mitltlatltl@gmail.com>
Reviewed-by: Daniel Thompson (RISCstar) <danielt@kernel.org>
Link: https://patch.msgid.link/20251109032240.3422503-3-caojunjie650@gmail.com
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
LED Backlight is a consumer of one or multiple LED class devices, but
devlink is currently unable to create correct supplier-producer links when
the supplier is a class device. It creates instead a link where the
supplier is the parent of the expected device.
One consequence is that removal order is not correctly enforced.
Issues happen for example with the following sections in a device tree
overlay:
// An LED driver chip
pca9632@62 {
compatible = "nxp,pca9632";
reg = <0x62>;
// ...
addon_led_pwm: led-pwm@3 {
reg = <3>;
label = "addon:led:pwm";
};
};
backlight-addon {
compatible = "led-backlight";
leds = <&addon_led_pwm>;
brightness-levels = <255>;
default-brightness-level = <255>;
};
In this example, the devlink should be created between the backlight-addon
(consumer) and the pca9632@62 (supplier). Instead it is created between the
backlight-addon (consumer) and the parent of the pca9632@62, which is
typically the I2C bus adapter.
On removal of the above overlay, the LED driver can be removed before the
backlight device, resulting in:
Unable to handle kernel NULL pointer dereference at virtual address 0000000000000010
...
Call trace:
led_put+0xe0/0x140
devm_led_release+0x6c/0x98
Another way to reproduce the bug without any device tree overlays is
unbinding the LED class device (pca9632@62) before unbinding the consumer
(backlight-addon):
echo 11-0062 >/sys/bus/i2c/drivers/leds-pca963x/unbind
echo ...backlight-dock >/sys/bus/platform/drivers/led-backlight/unbind
Fix by adding a devlink between the consuming led-backlight device and the
supplying LED device, as other drivers and subsystems do as well.
Fixes: ae232e45acf9 ("backlight: add led-backlight driver")
Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Reviewed-by: Daniel Thompson (RISCstar) <danielt@kernel.org>
Reviewed-by: Herve Codina <herve.codina@bootlin.com>
Tested-by: Alexander Sverdlin <alexander.sverdlin@siemens.com>
Link: https://patch.msgid.link/20250519-led-backlight-add-devlink-to-supplier-class-device-v6-1-845224aeb2ce@bootlin.com
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
Commit 27e8fe0da3b7 ("mmc: sdhci-of-dwcmshc: Prevent stale command
interrupt handling") clears pending interrupts when resetting
host->pending_reset to ensure no pending stale interrupts after
sdhci_threaded_irq restores interrupts. But this fix is only added for
th1520 platforms, in fact per my test, this issue exists on all
dwcmshc users, such as cv1800b, sg2002, and synaptics platforms.
So promote the above reset handling from th1520 to ip level. And keep
reset handling on rk, sg2042 and bf3 as is, until it's confirmed that
the same issue exists on these platforms too.
Fixes: 017199c2849c ("mmc: sdhci-of-dwcmshc: Add support for Sophgo CV1800B and SG2002")
Signed-off-by: Jisheng Zhang <jszhang@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
According to the hardware programming guide, the clock frequency must
remain below 52MHz during the transition to HS400 mode.
However,in the current implementation, the timing is set to HS400 (a
DDR mode) before adjusting the clock. This causes the clock to double
prematurely to 104MHz during the transition phase, violating the
specification and potentially resulting in CRC errors or CMD timeouts.
This change ensures that clock doubling is avoided during intermediate
transitions and is applied only when the card requires a 200MHz clock
for HS400 operation.
Signed-off-by: Sarthak Garg <sarthak.garg@oss.qualcomm.com>
Reviewed-by: Bjorn Andersson <andersson@kernel.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
When I added command queue engine (CQE) support for the Rockchip eMMC
controller, I missed that RK3576 has a separate platform data struct.
While things are working fine on RK3588 (I tested the ROCK 5B) and
the suspend issue is fixed on the RK3576 (I tested the Sige5), this
results in stability issues. By also adding the necessary hooks for
the RK3576 platform the following problems can be avoided:
[ 15.606895] mmc0: running CQE recovery
[ 15.616189] mmc0: running CQE recovery
[...]
[ 25.911484] mmc0: running CQE recovery
[ 25.926305] mmc0: running CQE recovery
[ 25.927468] mmc0: running CQE recovery
[...]
[ 26.255719] mmc0: running CQE recovery
[ 26.257162] ------------[ cut here ]------------
[ 26.257581] mmc0: cqhci: spurious TCN for tag 31
[ 26.258034] WARNING: CPU: 0 PID: 0 at drivers/mmc/host/cqhci-core.c:796 cqhci_irq+0x440/0x68c
[ 26.263786] CPU: 0 UID: 0 PID: 0 Comm: swapper/0 Not tainted 6.18.0-rc6-gd984ebbf0d15 #1 PREEMPT
[ 26.264561] Hardware name: ArmSoM Sige5 (DT)
[...]
[ 26.272748] Call trace:
[ 26.272964] cqhci_irq+0x440/0x68c (P)
[ 26.273296] dwcmshc_cqe_irq_handler+0x54/0x88
[ 26.273689] sdhci_irq+0xbc/0x1200
[ 26.273991] __handle_irq_event_percpu+0x54/0x1d0
[...]
Note that the above problems do not necessarily happen with every boot.
Reported-by: Adrian Hunter <adrian.hunter@intel.com>
Closes: https://lore.kernel.org/linux-rockchip/01949bc9-4873-498b-ac7d-f008393ccc4c@intel.com/
Fixes: fda1e0af7c28f ("mmc: sdhci-of-dwcmshc: Add command queue support for rockchip SOCs")
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Since 0f67b56d84b4c ("clocksource/drivers/arm_arch_timer_mmio: Switch
over to standalone driver"), acpi_arch_timer_mem_init() is unused.
Remove it.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Cc: Hanjun Guo <guohanjun@huawei.com>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Cc: Rafael J. Wysocki <rafael@kernel.org>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Mark Rutland <mark.rutland@arm.com>
Acked-by: Hanjun Guo <guohanjun@huawei.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
gpy_update_interface() returns early in case the PHY is internal or
connected via USXGMII. In this case the gigabit master/slave property
as well as MDI/MDI-X status also won't be read which seems wrong.
Always read those properties by moving the logic to retrieve them to
gpy_read_status().
Fixes: fd8825cd8c6fc ("net: phy: mxl-gpy: Add PHY Auto/MDI/MDI-X set driver for GPY211 chips")
Fixes: 311abcdddc00a ("net: phy: add support to get Master-Slave configuration")
Suggested-by: "Russell King (Oracle)" <linux@armlinux.org.uk>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Link: https://patch.msgid.link/71fccf3f56742116eb18cc070d2a9810479ea7f9.1763650701.git.daniel@makrotopia.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Protect access to fore200e->available_cell_rate with rate_mtx lock in the
error handling path of fore200e_open() to prevent a data race.
The field fore200e->available_cell_rate is a shared resource used to track
available bandwidth. It is concurrently accessed by fore200e_open(),
fore200e_close(), and fore200e_change_qos().
In fore200e_open(), the lock rate_mtx is correctly held when subtracting
vcc->qos.txtp.max_pcr from available_cell_rate to reserve bandwidth.
However, if the subsequent call to fore200e_activate_vcin() fails, the
function restores the reserved bandwidth by adding back to
available_cell_rate without holding the lock.
This introduces a race condition because available_cell_rate is a global
device resource shared across all VCCs. If the error path in
fore200e_open() executes concurrently with operations like
fore200e_close() or fore200e_change_qos() on other VCCs, a
read-modify-write race occurs.
Specifically, the error path reads the rate without the lock. If another
CPU acquires the lock and modifies the rate (e.g., releasing bandwidth in
fore200e_close()) between this read and the subsequent write, the error
path will overwrite the concurrent update with a stale value. This results
in incorrect bandwidth accounting.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Cc: stable@vger.kernel.org
Signed-off-by: Gui-Dong Han <hanguidong02@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20251120120657.2462194-1-hanguidong02@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The IRQ numbers created through irq_create_mapping() are only assigned
to ptpmsg_irq[n].num at the end of the IRQ setup. So if an error occurs
between their creation and their assignment (for instance during the
request_threaded_irq() step), we enter the error path and fail to
release the newly created virtual IRQs because they aren't yet assigned
to ptpmsg_irq[n].num.
Move the mapping creation to ksz_ptp_msg_irq_setup() to ensure symetry
with what's released by ksz_ptp_msg_irq_free().
In the error path, move the irq_dispose_mapping to the out_ptp_msg label
so it will be called only on created IRQs.
Cc: stable@vger.kernel.org
Fixes: cc13ab18b201 ("net: dsa: microchip: ptp: enable interrupt for timestamping")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Bastien Curutchet (Schneider Electric) <bastien.curutchet@bootlin.com>
Link: https://patch.msgid.link/20251120-ksz-fix-v6-5-891f80ae7f8f@bootlin.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
If a port interrupt setup fails after at least one port has already been
successfully initialized, the gotos miss some resource releasing:
- the already initialized PTP IRQs aren't released
- the already initialized port IRQs aren't released if the failure
occurs in ksz_pirq_setup().
Merge 'out_girq' and 'out_ptpirq' into a single 'port_release' label.
Behind this label, use the reverse loop to release all IRQ resources
for all initialized ports.
Jump in the middle of the reverse loop if an error occurs in
ksz_ptp_irq_setup() to only release the port IRQ of the current
iteration.
Cc: stable@vger.kernel.org
Fixes: c9cd961c0d43 ("net: dsa: microchip: lan937x: add interrupt support for port phy link")
Signed-off-by: Bastien Curutchet (Schneider Electric) <bastien.curutchet@bootlin.com>
Link: https://patch.msgid.link/20251120-ksz-fix-v6-4-891f80ae7f8f@bootlin.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
If something goes wrong at setup, ksz_irq_free() can be called on
uninitialized ksz_irq (for example when ksz_ptp_irq_setup() fails). It
leads to freeing uninitialized IRQ numbers and/or domains.
Use dsa_switch_for_each_user_port_continue_reverse() in the error path
to iterate only over the fully initialized ports.
Cc: stable@vger.kernel.org
Fixes: cc13ab18b201 ("net: dsa: microchip: ptp: enable interrupt for timestamping")
Signed-off-by: Bastien Curutchet (Schneider Electric) <bastien.curutchet@bootlin.com>
Link: https://patch.msgid.link/20251120-ksz-fix-v6-3-891f80ae7f8f@bootlin.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
irq_find_mapping() returns a positive IRQ number or 0 if no IRQ is found
but it never returns a negative value. However, during the PTP IRQ setup,
we verify that its returned value isn't negative.
Fix the irq_find_mapping() check to enter the error path when 0 is
returned. Return -EINVAL in such case.
Cc: stable@vger.kernel.org
Fixes: cc13ab18b201 ("net: dsa: microchip: ptp: enable interrupt for timestamping")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Bastien Curutchet (Schneider Electric) <bastien.curutchet@bootlin.com>
Link: https://patch.msgid.link/20251120-ksz-fix-v6-2-891f80ae7f8f@bootlin.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
irq_find_mapping() returns a positive IRQ number or 0 if no IRQ is found
but it never returns a negative value. However, on each
irq_find_mapping() call, we verify that the returned value isn't
negative.
Fix the irq_find_mapping() checks to enter error paths when 0 is
returned. Return -EINVAL in such cases.
CC: stable@vger.kernel.org
Fixes: c9cd961c0d43 ("net: dsa: microchip: lan937x: add interrupt support for port phy link")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Bastien Curutchet (Schneider Electric) <bastien.curutchet@bootlin.com>
Link: https://patch.msgid.link/20251120-ksz-fix-v6-1-891f80ae7f8f@bootlin.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
ATL2 hardware was missing descriptor cache invalidation in hw_stop(),
causing SMMU translation faults during device shutdown and module removal:
[ 70.355743] arm-smmu-v3 arm-smmu-v3.5.auto: event 0x10 received:
[ 70.361893] arm-smmu-v3 arm-smmu-v3.5.auto: 0x0002060000000010
[ 70.367948] arm-smmu-v3 arm-smmu-v3.5.auto: 0x0000020000000000
[ 70.374002] arm-smmu-v3 arm-smmu-v3.5.auto: 0x00000000ff9bc000
[ 70.380055] arm-smmu-v3 arm-smmu-v3.5.auto: 0x0000000000000000
[ 70.386109] arm-smmu-v3 arm-smmu-v3.5.auto: event: F_TRANSLATION client: 0001:06:00.0 sid: 0x20600 ssid: 0x0 iova: 0xff9bc000 ipa: 0x0
[ 70.398531] arm-smmu-v3 arm-smmu-v3.5.auto: unpriv data write s1 "Input address caused fault" stag: 0x0
Commit 7a1bb49461b1 ("net: aquantia: fix potential IOMMU fault after
driver unbind") and commit ed4d81c4b3f2 ("net: aquantia: when cleaning
hw cache it should be toggled") fixed cache invalidation for ATL B0, but
ATL2 was left with only interrupt disabling. This allowed hardware to
write to cached descriptors after DMA memory was unmapped, triggering
SMMU faults. Once cache invalidation is applied to ATL2, the translation
fault can't be observed anymore.
Add shared aq_hw_invalidate_descriptor_cache() helper and use it in both
ATL B0 and ATL2 hw_stop() implementations for consistent behavior.
Fixes: e54dcf4bba3e ("net: atlantic: basic A2 init/deinit hw_ops")
Tested-by: Carol Soto <csoto@nvidia.com>
Signed-off-by: Kai-Heng Feng <kaihengf@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20251120041537.62184-1-kaihengf@nvidia.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/ti/linux into soc/drivers
TI SoC driver updates for v6.19
- ti_sci: Add Partial-IO poweroff support and sys_off handler integration
- ti_sci: Gate IO isolation programming on firmware capability flag
- ti_sci: cleanup by replacing ifdeffery in PM ops with pm_sleep_ptr() macro
* tag 'ti-driver-soc-for-v6.19' of https://git.kernel.org/pub/scm/linux/kernel/git/ti/linux:
firmware: ti_sci: Partial-IO support
firmware: ti_sci: Support transfers without response
firmware: ti_sci: Set IO Isolation only if the firmware is capable
firmware: ti_sci: Replace ifdeffery by pm_sleep_ptr() macro
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
