| Age | Commit message (Collapse) | Author |
|---|
|
Introduce helper functions to suspend and resume DMA operations. These
are required to prepare for upcoming Runtime PM support, ensuring that
DMA state is properly managed during power transitions.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://patch.msgid.link/20260113072702.16268-12-adrian.hunter@intel.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
Split the ring setup logic out of hci_dma_init() into a new helper
hci_dma_init_rings(). This refactoring prepares for Runtime PM support
by allowing DMA rings to be reinitialized independently after resume.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://patch.msgid.link/20260113072702.16268-11-adrian.hunter@intel.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
Add a dedicated function to restore the Device Address Table (DAT) in
preparation for Runtime PM support. This will allow reprogramming the DAT
after the controller resumes from a low-power state.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://patch.msgid.link/20260113072702.16268-10-adrian.hunter@intel.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
Prepare for Runtime PM support, which requires restoring the Device Address
Table (DAT) registers after resume. Maintain a copy of DAT in memory so it
can be reprogrammed when the controller is powered back up.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://patch.msgid.link/20260113072702.16268-9-adrian.hunter@intel.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
The driver already uses devres for resource management, but the standard
resource-managed DMA allocation helpers cannot be used because they assume
the DMA device matches the managed device.
To address this, factor out the deallocation logic from hci_dma_cleanup()
into a new helper, hci_dma_free(), and register it as a devres action.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://patch.msgid.link/20260113072702.16268-8-adrian.hunter@intel.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
The driver already uses managed resources, so convert the PIO data
structure allocation to devm_zalloc(). Remove the manual kfree().
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://patch.msgid.link/20260113072702.16268-7-adrian.hunter@intel.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
The driver already uses managed resources, so convert the Device Address
Table (DAT) bitmap allocation to use devm_bitmap_zalloc(). Remove the
manual cleanup routine.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://patch.msgid.link/20260113072702.16268-6-adrian.hunter@intel.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
IBI disable failures are not indicative of a software bug, so using
WARN_ON() is not appropriate. Replace these warnings with dev_err().
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://patch.msgid.link/20260113072702.16268-5-adrian.hunter@intel.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
To prevent inconsistent state when an error occurs, ensure the hot-join
flag is updated only when enabling or disabling hot-join succeeds.
Fixes: 317bacf960a48 ("i3c: master: add enable(disable) hot join in sys entry")
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://patch.msgid.link/20260113072702.16268-4-adrian.hunter@intel.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
Wait for the bus to fully disable before proceeding, ensuring that no
operations are still in progress. Synchronize the IRQ handler only after
interrupt signals have been disabled. This approach also handles cases
where bus disable might fail, preventing race conditions and ensuring a
consistent shutdown sequence.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://patch.msgid.link/20260113072702.16268-3-adrian.hunter@intel.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
The MIPI I3C HCI specification does not define reset values for
RING_OPERATION1 fields, and some controllers (e.g., Intel) do not clear
them during a software reset. Ensure the ring pointers are explicitly
set to zero during bus initialization to avoid inconsistent state.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://patch.msgid.link/20260113072702.16268-2-adrian.hunter@intel.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media fixes from Mauro Carvalho Chehab:
- ov02c10: some fixes related to preserving bayer pattern and
horizontal control
- ipu-bridge: Add quirks for some Dell XPS laptops with inverted
sensors
- mali-c55: Fix version identifier logic
- rzg2l-cru: csi-2: fix RZ/V2H input sizes on some variants
* tag 'media/v6.19-3' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
media: ov02c10: Remove unnecessary hflip and vflip pointers
media: ipu-bridge: Add DMI quirk for Dell XPS laptops with upside down sensors
media: ov02c10: Fix the horizontal flip control
media: ov02c10: Adjust x-win/y-win when changing flipping to preserve bayer-pattern
media: ov02c10: Fix bayer-pattern change after default vflip change
media: rzg2l-cru: csi-2: Support RZ/V2H input sizes
media: uapi: mali-c55-config: Remove version identifier
media: mali-c55: Remove duplicated version check
media: Documentation: mali-c55: Use v4l2-isp version identifier
|
|
During pre-production development, drivers may provide both ACPI and OF
match tables while a formal ACPI HID for the device is not yet
allocated. Such devices are enumerated via PRP0001. In this case,
acpi_device_get_match_data() consults only the driver’s ACPI match table
and returns NULL, even though the device was successfully matched via
PRP0001.
This behavior also risks breaking existing PRP0001 setups if a driver
later gains an ACPI HID, as the presence of an ACPI match table changes
the match-data lookup path.
Make acpi_device_get_match_data() use the same precedence as driver
matching by using __acpi_match_device(). Return match data from the
acpi_id or of_id that was actually matched.
Remove now-unused acpi_of_device_get_match_data().
Signed-off-by: Kartik Rajput <kkartik@nvidia.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Link: https://patch.msgid.link/20260114082306.48119-1-kkartik@nvidia.com
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
After U-Boot initializes PCIe with "pcie enum", Linux fails to detect
an NVMe disk on some boot cycles with:
phy phy-32f00000.pcie-phy.0: phy poweron failed --> -110
Discussion with NXP identified that the iMX8MP PCIe PHY PLL may fail to
lock when re-initialized without a reset cycle [1].
The issue reproduces on 7% of tested hardware platforms, with a 30-40%
failure rate per affected device across boot cycles.
Insert a reset cycle in the power-on routine to ensure the PHY is
initialized from a known state.
[1] https://community.nxp.com/t5/i-MX-Processors/iMX8MP-PCIe-initialization-in-U-Boot/m-p/2248437#M242401
Signed-off-by: Rafael Beims <rafael.beims@toradex.com>
Cc: stable@vger.kernel.org
Link: https://patch.msgid.link/20251223150254.1075221-1-rafael@beims.me
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
When Firmware First is enabled, BIOS handles errors first and then it
makes them available to the kernel via the Common Platform Error Record
(CPER) sections (UEFI 2.11 Appendix N.2.13). Linux parses the CPER
sections via one of two similar paths, either ELOG or GHES. The errors
managed by ELOG are signaled to the BIOS by the I/O Machine Check
Architecture (I/O MCA).
Currently, ELOG and GHES show some inconsistencies in how they report to
userspace via trace events.
Therefore, make the two mentioned paths act similarly by tracing the CPER
CXL Protocol Error Section.
Reviewed-by: Dave Jiang <dave.jiang@intel.com>
Reviewed-by: Jonathan Cameron <jonathan.cameron@huawei.com>
Reviewed-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Signed-off-by: Fabio M. De Francesco <fabio.m.de.francesco@linux.intel.com>
Link: https://patch.msgid.link/20260114101543.85926-6-fabio.m.de.francesco@linux.intel.com
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Make a helper out of cxl_cper_post_prot_err() that checks the CXL agent
type and copy the CPER CXL protocol errors information to a work data
structure.
Export the new symbol for reuse by ELOG.
Reviewed-by: Dave Jiang <dave.jiang@intel.com>
Reviewed-by: Jonathan Cameron <jonathan.cameron@huawei.com>
Reviewed-by: Hanjun Guo <guohanjun@huawei.com>
Signed-off-by: Fabio M. De Francesco <fabio.m.de.francesco@linux.intel.com>
[ rjw: Subject tweak ]
Link: https://patch.msgid.link/20260114101543.85926-5-fabio.m.de.francesco@linux.intel.com
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Move the CPER CXL protocol errors validity check out of
cxl_cper_post_prot_err() to new cxl_cper_sec_prot_err_valid() and limit
the serial number check only to CXL agents that are CXL devices (UEFI
v2.10, Appendix N.2.13).
Export the new symbol for reuse by ELOG.
Reviewed-by: Dave Jiang <dave.jiang@intel.com>
Reviewed-by: Hanjun Guo <guohanjun@huawei.com>
Reviewed-by: Jonathan Cameron <jonathan.cameron@huawei.com>
Signed-off-by: Fabio M. De Francesco <fabio.m.de.francesco@linux.intel.com>
[ rjw: Subject tweak ]
Link: https://patch.msgid.link/20260114101543.85926-4-fabio.m.de.francesco@linux.intel.com
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
I/O Machine Check Architecture events may signal failing PCIe components
or links. The AER event contains details on what was happening on the wire
when the error was signaled.
Trace the CPER PCIe Error section (UEFI v2.11, Appendix N.2.7) reported
by the I/O MCA.
Reviewed-by: Dave Jiang <dave.jiang@intel.com>
Reviewed-by: Jonathan Cameron <jonathan.cameron@huawei.com>
Signed-off-by: Fabio M. De Francesco <fabio.m.de.francesco@linux.intel.com>
Link: https://patch.msgid.link/20260114101543.85926-3-fabio.m.de.francesco@linux.intel.com
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
ghes_do_proc() has a catch-all for unknown or unhandled CPER formats
(UEFI v2.11 Appendix N 2.3), extlog_print() does not. This gap was
noticed by a RAS test that injected CXL protocol errors which were
notified to extlog_print() via the IOMCA (I/O Machine Check
Architecture) mechanism. Bring parity to the extlog_print() path by
including a similar log_non_standard_event().
Reviewed-by: Dan Williams <dan.j.williams@intel.com>
Reviewed-by: Dave Jiang <dave.jiang@intel.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Reviewed-by: Qiuxu Zhuo <qiuxu.zhuo@intel.com>
Reviewed-by: Shuai Xue <xueshuai@linux.alibaba.com>
Signed-off-by: Fabio M. De Francesco <fabio.m.de.francesco@linux.intel.com>
Link: https://patch.msgid.link/20260114101543.85926-2-fabio.m.de.francesco@linux.intel.com
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Performance testing on ARMv8 systems shows significant overhead in error
status handling in SEA error handling.
- ghes_peek_estatus(): 8,138.3 ns (21,160 cycles).
- ghes_clear_estatus(): 2,038.3 ns (5,300 cycles).
Apply the same optimization used in ghes_notify_nmi() to
ghes_notify_sea() by checking for active errors before processing,
Tested-by: Tony Luck <tony.luck@intel.com>
Reviewed-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Shuai Xue <xueshuai@linux.alibaba.com>
Reviewed-by: Hanjun Guo <guohanjun@huawei.com>
Link: https://patch.msgid.link/20260112032239.30023-4-xueshuai@linux.alibaba.com
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Refactors the GHES driver by extracting common functionality into
reusable helper functions:
1. ghes_has_active_errors() - Checks if any error sources in a given list
have active errors
2. ghes_map_error_status() - Maps error status address to virtual address
3. ghes_unmap_error_status() - Unmaps error status virtual address
4. Use `guard(rcu)()` instead of explicit `rcu_read_lock()`/`rcu_read_unlock()`.
These helpers eliminate code duplication in the NMI path and prepare for
similar usage in the SEA path in a subsequent patch.
No functional change intended.
Tested-by: Tony Luck <tony.luck@intel.com>
Reviewed-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Shuai Xue <xueshuai@linux.alibaba.com>
Reviewed-by: Breno Leitao <leitao@debian.org>
Reviewed-by: Hanjun Guo <guohanjun@huawei.com>
Link: https://patch.msgid.link/20260112032239.30023-3-xueshuai@linux.alibaba.com
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
ghes_notify_nmi() is called for every NMI and must check whether the NMI was
generated because an error was signalled by platform firmware.
This check is very expensive as for each registered GHES NMI source it reads
from the acpi generic address attached to this error source to get the physical
address of the acpi_hest_generic_status block. It then checks the "block_status"
to see if an error was logged.
The ACPI/APEI code must create virtual mappings for each of those physical
addresses, and tear them down afterwards. On an Icelake system this takes around
15,000 TSC cycles. Enough to disturb efforts to profile system performance.
If that were not bad enough, there are some atomic accesses in the code path
that will cause cache line bounces between CPUs. A problem that gets worse as
the core count increases.
But BIOS changes neither the acpi generic address nor the physical address of
the acpi_hest_generic_status block. So this walk can be done once when the NMI is
registered to save the virtual address (unmapping if the NMI is ever unregistered).
The "block_status" can be checked directly in the NMI handler. This can be done
without any atomic accesses.
Resulting time to check that there is not an error record is around 900 cycles.
Reported-by: Andi Kleen <andi.kleen@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Tested-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Shuai Xue <xueshuai@linux.alibaba.com>
Reviewed-by: Hanjun Guo <guohanjun@huawei.com>
Link: https://patch.msgid.link/20260112032239.30023-2-xueshuai@linux.alibaba.com
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The current logic at cper_print_fw_err() doesn't check if the
error record length is big enough to handle offset. On a bad firmware,
if the ofset is above the actual record, length -= offset will
underflow, making it dump the entire memory.
The end result can be:
- the logic taking a lot of time dumping large regions of memory;
- data disclosure due to the memory dumps;
- an OOPS, if it tries to dump an unmapped memory region.
Fix it by checking if the section length is too small before doing
a hex dump.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Reviewed-by: Jonathan Cameron <jonathan.cameron@huawei.com>
Acked-by: Ard Biesheuvel <ardb@kernel.org>
Reviewed-by: Hanjun Guo <guohanjun@huawei.com>
[ rjw: Subject tweaks ]
Link: https://patch.msgid.link/1752b5ba63a3e2f148ddee813b36c996cc617e86.1767871950.git.mchehab+huawei@kernel.org
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The logic at ghes_new() prevents allocating too large records, by
checking if they're bigger than GHES_ESTATUS_MAX_SIZE (currently, 64KB).
Yet, the allocation is done with the actual number of pages from the
CPER bios table location, which can be smaller.
Yet, a bad firmware could send data with a different size, which might
be bigger than the allocated memory, causing an OOPS:
Unable to handle kernel paging request at virtual address fff00000f9b40000
Mem abort info:
ESR = 0x0000000096000007
EC = 0x25: DABT (current EL), IL = 32 bits
SET = 0, FnV = 0
EA = 0, S1PTW = 0
FSC = 0x07: level 3 translation fault
Data abort info:
ISV = 0, ISS = 0x00000007, ISS2 = 0x00000000
CM = 0, WnR = 0, TnD = 0, TagAccess = 0
GCS = 0, Overlay = 0, DirtyBit = 0, Xs = 0
swapper pgtable: 4k pages, 52-bit VAs, pgdp=000000008ba16000
[fff00000f9b40000] pgd=180000013ffff403, p4d=180000013fffe403, pud=180000013f85b403, pmd=180000013f68d403, pte=0000000000000000
Internal error: Oops: 0000000096000007 [#1] SMP
Modules linked in:
CPU: 0 UID: 0 PID: 303 Comm: kworker/0:1 Not tainted 6.19.0-rc1-00002-gda407d200220 #34 PREEMPT
Hardware name: QEMU QEMU Virtual Machine, BIOS unknown 02/02/2022
Workqueue: kacpi_notify acpi_os_execute_deferred
pstate: 214020c5 (nzCv daIF +PAN -UAO -TCO +DIT -SSBS BTYPE=--)
pc : hex_dump_to_buffer+0x30c/0x4a0
lr : hex_dump_to_buffer+0x328/0x4a0
sp : ffff800080e13880
x29: ffff800080e13880 x28: ffffac9aba86f6a8 x27: 0000000000000083
x26: fff00000f9b3fffc x25: 0000000000000004 x24: 0000000000000004
x23: ffff800080e13905 x22: 0000000000000010 x21: 0000000000000083
x20: 0000000000000001 x19: 0000000000000008 x18: 0000000000000010
x17: 0000000000000001 x16: 00000007c7f20fec x15: 0000000000000020
x14: 0000000000000008 x13: 0000000000081020 x12: 0000000000000008
x11: ffff800080e13905 x10: ffff800080e13988 x9 : 0000000000000000
x8 : 0000000000000000 x7 : 0000000000000001 x6 : 0000000000000020
x5 : 0000000000000030 x4 : 00000000fffffffe x3 : 0000000000000000
x2 : ffffac9aba78c1c8 x1 : ffffac9aba76d0a8 x0 : 0000000000000008
Call trace:
hex_dump_to_buffer+0x30c/0x4a0 (P)
print_hex_dump+0xac/0x170
cper_estatus_print_section+0x90c/0x968
cper_estatus_print+0xf0/0x158
__ghes_print_estatus+0xa0/0x148
ghes_proc+0x1bc/0x220
ghes_notify_hed+0x5c/0xb8
notifier_call_chain+0x78/0x148
blocking_notifier_call_chain+0x4c/0x80
acpi_hed_notify+0x28/0x40
acpi_ev_notify_dispatch+0x50/0x80
acpi_os_execute_deferred+0x24/0x48
process_one_work+0x15c/0x3b0
worker_thread+0x2d0/0x400
kthread+0x148/0x228
ret_from_fork+0x10/0x20
Code: 6b14033f 540001ad a94707e2 f100029f (b8747b44)
---[ end trace 0000000000000000 ]---
Prevent that by taking the actual allocated are into account when
checking for CPER length.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Reviewed-by: Jonathan Cameron <jonathan.cameron@huawei.com>
Acked-by: Ard Biesheuvel <ardb@kernel.org>
Reviewed-by: Hanjun Guo <guohanjun@huawei.com>
[ rjw: Subject tweaks ]
Link: https://patch.msgid.link/4e70310a816577fabf37d94ed36cde4ad62b1e0a.1767871950.git.mchehab+huawei@kernel.org
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
There's a logic inside GHES/CPER to detect if the section_length
is too small, but it doesn't detect if it is too big.
Currently, if the firmware receives an ARM processor CPER record
stating that a section length is big, kernel will blindly trust
section_length, producing a very long dump. For instance, a 67
bytes record with ERR_INFO_NUM set 46198 and section length
set to 854918320 would dump a lot of data going a way past the
firmware memory-mapped area.
Fix it by adding a logic to prevent it to go past the buffer
if ERR_INFO_NUM is too big, making it report instead:
[Hardware Error]: Hardware error from APEI Generic Hardware Error Source: 1
[Hardware Error]: event severity: recoverable
[Hardware Error]: Error 0, type: recoverable
[Hardware Error]: section_type: ARM processor error
[Hardware Error]: MIDR: 0xff304b2f8476870a
[Hardware Error]: section length: 854918320, CPER size: 67
[Hardware Error]: section length is too big
[Hardware Error]: firmware-generated error record is incorrect
[Hardware Error]: ERR_INFO_NUM is 46198
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Reviewed-by: Jonathan Cameron <jonathan.cameron@huawei.com>
Acked-by: Ard Biesheuvel <ardb@kernel.org>
Reviewed-by: Hanjun Guo <guohanjun@huawei.com>
[ rjw: Subject and changelog tweaks ]
Link: https://patch.msgid.link/41cd9f6b3ace3cdff7a5e864890849e4b1c58b63.1767871950.git.mchehab+huawei@kernel.org
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
If the BIOS generates a very small ARM Processor Error, or
an incomplete one, the current logic will fail to deferrence
err->section_length
and
ctx_info->size
Add checks to avoid that. With such changes, such GHESv2
records won't cause OOPSes like this:
[ 1.492129] Internal error: Oops: 0000000096000005 [#1] SMP
[ 1.495449] Modules linked in:
[ 1.495820] CPU: 0 UID: 0 PID: 9 Comm: kworker/0:0 Not tainted 6.18.0-rc1-00017-gabadcc3553dd-dirty #18 PREEMPT
[ 1.496125] Hardware name: QEMU QEMU Virtual Machine, BIOS unknown 02/02/2022
[ 1.496433] Workqueue: kacpi_notify acpi_os_execute_deferred
[ 1.496967] pstate: 814000c5 (Nzcv daIF +PAN -UAO -TCO +DIT -SSBS BTYPE=--)
[ 1.497199] pc : log_arm_hw_error+0x5c/0x200
[ 1.497380] lr : ghes_handle_arm_hw_error+0x94/0x220
0xffff8000811c5324 is in log_arm_hw_error (../drivers/ras/ras.c:75).
70 err_info = (struct cper_arm_err_info *)(err + 1);
71 ctx_info = (struct cper_arm_ctx_info *)(err_info + err->err_info_num);
72 ctx_err = (u8 *)ctx_info;
73
74 for (n = 0; n < err->context_info_num; n++) {
75 sz = sizeof(struct cper_arm_ctx_info) + ctx_info->size;
76 ctx_info = (struct cper_arm_ctx_info *)((long)ctx_info + sz);
77 ctx_len += sz;
78 }
79
and similar ones while trying to access section_length on an
error dump with too small size.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Reviewed-by: Jonathan Cameron <jonathan.cameron@huawei.com>
Acked-by: Ard Biesheuvel <ardb@kernel.org>
Reviewed-by: Hanjun Guo <guohanjun@huawei.com>
[ rjw: Subject tweaks ]
Link: https://patch.msgid.link/7fd9f38413be05ee2d7cfdb0dc31ea2274cf1a54.1767871950.git.mchehab+huawei@kernel.org
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The commit d2fe192348f9 (“nvme: only allow entering LIVE from CONNECTING
state”) disallows controller state transitions directly from RESETTING
to LIVE. However, the NVMe PCIe subsystem reset path relies on this
transition to recover the controller on PowerPC (PPC) systems.
On PPC systems, issuing a subsystem reset causes a temporary loss of
communication with the NVMe adapter. A subsequent PCIe MMIO read then
triggers EEH recovery, which restores the PCIe link and brings the
controller back online. For EEH recovery to proceed correctly, the
controller must transition back to the LIVE state.
Due to the changes introduced by commit d2fe192348f9 (“nvme: only allow
entering LIVE from CONNECTING state”), the controller can no longer
transition directly from RESETTING to LIVE. As a result, EEH recovery
exits prematurely, leaving the controller stuck in the RESETTING state.
Fix this by explicitly transitioning the controller state from RESETTING
to CONNECTING and then to LIVE. This satisfies the updated state
transition rules and allows the controller to be successfully recovered
on PPC systems following a PCIe subsystem reset.
Cc: stable@vger.kernel.org
Fixes: d2fe192348f9 ("nvme: only allow entering LIVE from CONNECTING state")
Reviewed-by: Daniel Wagner <dwagner@suse.de>
Signed-off-by: Nilay Shroff <nilay@linux.ibm.com>
Signed-off-by: Keith Busch <kbusch@kernel.org>
|
|
Based on the reality[1][2] that vb2_dma_sg_alloc() can't alloc buffer with
device DMA limits, those device will always get below error: "swiotlb
buffer is full (sz: 393216 bytes), total 65536 (slots), used 2358 (slots)"
and the uvc gadget function can't work at all.
The videobuf2-dma-sg.c driver doesn't has a formal improve about this issue
till now. For UVC gadget, the videobuf2 subsystem doesn't do dma_map() on
vmalloc returned big buffer when allocate the video buffers, however, it do
it for dma_sg returned buffer. So the issue happens for vb2_dma_sg_alloc().
To workaround the issue, lets retry vb2_reqbufs() with
vb_vmalloc_memops if it fails to allocate buffer with vb2_dma_sg_memops.
If use vmalloced buffer, UVC gadget will allocate some small buffers for
each usb_request to do dma transfer, then uvc driver will memcopy data
from big buffer to small buffer.
Link[1]: https://lore.kernel.org/linux-media/20230828075420.2009568-1-anle.pan@nxp.com/
Link[2]: https://lore.kernel.org/linux-media/20230914145812.12851-1-hui.fang@nxp.com/
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://patch.msgid.link/20260113-uvc-gadget-fix-patch-v2-4-62950ef5bcb5@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
uvcg_queue_init() may fail, but its return value is currently ignored.
Propagate the error code from uvcg_queue_init() to correctly report
initialization failures.
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Link: https://patch.msgid.link/20260113-uvc-gadget-fix-patch-v2-3-62950ef5bcb5@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
According to USB specification:
For full-/high-speed isochronous endpoints, the bInterval value is
used as the exponent for a 2^(bInterval-1) value.
To correctly convert bInterval as interval_duration:
interval_duration = 2^(bInterval-1) * frame_interval
Because the unit of video->interval is 100ns, add a comment info to
make it clear.
Fixes: 48dbe731171e ("usb: gadget: uvc: set req_size and n_requests based on the frame interval")
Cc: stable@vger.kernel.org
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Link: https://patch.msgid.link/20260113-uvc-gadget-fix-patch-v2-2-62950ef5bcb5@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Current req_payload_size calculation has 2 issue:
(1) When the first time calculate req_payload_size for all the buffers,
reqs_per_frame = 0 will be the divisor of DIV_ROUND_UP(). So
the result is undefined.
This happens because VIDIOC_STREAMON is always executed after
VIDIOC_QBUF. So video->reqs_per_frame will be 0 until VIDIOC_STREAMON
is run.
(2) The buf->req_payload_size may be bigger than max_req_size.
Take YUYV pixel format as example:
If bInterval = 1, video->interval = 666666, high-speed:
video->reqs_per_frame = 666666 / 1250 = 534
720p: buf->req_payload_size = 1843200 / 534 = 3452
1080p: buf->req_payload_size = 4147200 / 534 = 7766
Based on such req_payload_size, the controller can't run normally.
To fix above issue, assign max_req_size to buf->req_payload_size when
video->reqs_per_frame = 0. And limit buf->req_payload_size to
video->req_size if it's large than video->req_size. Since max_req_size
is used at many place, add it to struct uvc_video and set the value once
endpoint is enabled.
Fixes: 98ad03291560 ("usb: gadget: uvc: set req_length based on payload by nreqs instead of req_size")
Cc: stable@vger.kernel.org
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Link: https://patch.msgid.link/20260113-uvc-gadget-fix-patch-v2-1-62950ef5bcb5@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Ignore USB role switches if dwc3-apple is already in the desired state.
The USB-C port controller on M2 and M1/M2 Pro/Max/Ultra devices issues
additional interrupts which result in USB role switches to the already
active role.
Ignore these USB role switches to ensure the USB-C port controller and
dwc3-apple are always in a consistent state. This matches the behaviour
in __dwc3_set_mode() in core.c.
Fixes detecting USB 2.0 and 3.x devices on the affected systems. The
reset caused by the additional role switch appears to leave the USB
devices in a state which prevents detection when the phy and dwc3 is
brought back up again.
Fixes: 0ec946d32ef7 ("usb: dwc3: Add Apple Silicon DWC3 glue layer driver")
Cc: stable <stable@kernel.org>
Signed-off-by: Janne Grunau <j@jannau.net>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Reviewed-by: Sven Peter <sven@kernel.org>
Tested-by: Sven Peter <sven@kernel.org> # M1 mac mini and macbook air
Link: https://patch.msgid.link/20260109-apple-dwc3-role-switch-v1-1-11623b0f6222@jannau.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
All MERT catastrophic errors but VF's LMTT fault are serious, so
we shouldn't limit our handling only to print debug messages.
Change CATERR message to error level and then declare the device
as wedged to match expectation from the design document. For the
LMTT faults, add a note about adding tracking of this unexpected
VF activity.
While at it, rename register fields defnitions to match the BSpec.
Also drop trailing include guard name from the regs.h file.
BSpec: 74625
Signed-off-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Lukasz Laguna <lukasz.laguna@intel.com>
Reviewed-by: Lukasz Laguna <lukasz.laguna@intel.com>
Link: https://patch.msgid.link/20260112183716.28700-1-michal.wajdeczko@intel.com
|
|
When some wake IRQs are disabled in the device tree, the corresponding
interrupt entries are removed from DT. In such cases, the driver
currently calls platform_get_irq(), which returns -ENXIO and logs
an error like:
tegra-xusb 3610000.usb: error -ENXIO: IRQ index 2 not found
However, not all wake IRQs are mandatory. The hardware can operate
normally even if some wake sources are not defined in DT. To avoid this
false alarm and allow missing wake IRQs gracefully, use
platform_get_irq_optional() instead of platform_get_irq().
Fixes: 5df186e2ef11 ("usb: xhci: tegra: Support USB wakeup function for Tegra234")
Cc: stable <stable@kernel.org>
Signed-off-by: Wayne Chang <waynec@nvidia.com>
Signed-off-by: Wei-Cheng Chen <weichengc@nvidia.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Link: https://patch.msgid.link/20260112145653.95691-1-weichengc@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Commit 9beeee6584b9aa4f ("USB: EHCI: log a warning if ehci-hcd is not
loaded first") said that ehci-hcd should be loaded before ohci-hcd and
uhci-hcd. However, commit 05c92da0c52494ca ("usb: ohci/uhci - add soft
dependencies on ehci_pci") only makes ohci-pci/uhci-pci depend on ehci-
pci, which is not enough and we may still see the warnings in boot log.
To eliminate the warnings we should make ohci-hcd/uhci-hcd depend on
ehci-hcd. But Alan said that the warning introduced by 9beeee6584b9aa4f
is bogus, we only need the soft dependencies in the PCI level rather
than the HCD level.
However, there is really another neccessary soft dependencies between
ohci-platform/uhci-platform and ehci-platform, which is added by this
patch. The boot logs are below.
1. ohci-platform loaded before ehci-platform:
ohci-platform 1f058000.usb: Generic Platform OHCI controller
ohci-platform 1f058000.usb: new USB bus registered, assigned bus number 1
ohci-platform 1f058000.usb: irq 28, io mem 0x1f058000
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 4 ports detected
Warning! ehci_hcd should always be loaded before uhci_hcd and ohci_hcd, not after
usb 1-4: new low-speed USB device number 2 using ohci-platform
ehci-platform 1f050000.usb: EHCI Host Controller
ehci-platform 1f050000.usb: new USB bus registered, assigned bus number 2
ehci-platform 1f050000.usb: irq 29, io mem 0x1f050000
ehci-platform 1f050000.usb: USB 2.0 started, EHCI 1.00
usb 1-4: device descriptor read/all, error -62
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 4 ports detected
usb 1-4: new low-speed USB device number 3 using ohci-platform
input: YSPRINGTECH USB OPTICAL MOUSE as /devices/platform/bus@10000000/1f058000.usb/usb1/1-4/1-4:1.0/0003:10C4:8105.0001/input/input0
hid-generic 0003:10C4:8105.0001: input,hidraw0: USB HID v1.11 Mouse [YSPRINGTECH USB OPTICAL MOUSE] on usb-1f058000.usb-4/input0
2. ehci-platform loaded before ohci-platform:
ehci-platform 1f050000.usb: EHCI Host Controller
ehci-platform 1f050000.usb: new USB bus registered, assigned bus number 1
ehci-platform 1f050000.usb: irq 28, io mem 0x1f050000
ehci-platform 1f050000.usb: USB 2.0 started, EHCI 1.00
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 4 ports detected
ohci-platform 1f058000.usb: Generic Platform OHCI controller
ohci-platform 1f058000.usb: new USB bus registered, assigned bus number 2
ohci-platform 1f058000.usb: irq 29, io mem 0x1f058000
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 4 ports detected
usb 2-4: new low-speed USB device number 2 using ohci-platform
input: YSPRINGTECH USB OPTICAL MOUSE as /devices/platform/bus@10000000/1f058000.usb/usb2/2-4/2-4:1.0/0003:10C4:8105.0001/input/input0
hid-generic 0003:10C4:8105.0001: input,hidraw0: USB HID v1.11 Mouse [YSPRINGTECH USB OPTICAL MOUSE] on usb-1f058000.usb-4/input0
In the later case, there is no re-connection for USB-1.0/1.1 devices,
which is expected.
Cc: stable <stable@kernel.org>
Reported-by: Shengwen Xiao <atzlinux@sina.com>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://patch.msgid.link/20260112084802.1995923-1-chenhuacai@loongson.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Now that the upstream code has been getting broader test coverage by our
users we occasionally see issues with USB2 devices plugged in during boot.
Before Linux is running, the USB2 PHY has usually been running in device
mode and it turns out that sometimes host->device or device->host
transitions don't work.
The root cause: If the role inside the USB2 PHY is re-configured when it
has already been powered on or when dwc3 has already enabled the ULPI
interface the new configuration sometimes doesn't take affect until dwc3
is reset again. Fix this rare issue by configuring the role much earlier.
Note that the USB3 PHY does not suffer from this issue and actually
requires dwc3 to be up before the correct role can be configured there.
Reported-by: James Calligeros <jcalligeros99@gmail.com>
Reported-by: Janne Grunau <j@jannau.net>
Fixes: 0ec946d32ef7 ("usb: dwc3: Add Apple Silicon DWC3 glue layer driver")
Cc: stable <stable@kernel.org>
Tested-by: Janne Grunau <j@jannau.net>
Reviewed-by: Janne Grunau <j@jannau.net>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Sven Peter <sven@kernel.org>
Link: https://patch.msgid.link/20260109-dwc3-apple-usb2phy-fix-v2-1-ab6b041e3b26@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The ChipIdea UDC driver can encounter "not page aligned sg buffer"
errors when a USB device is reconnected after being disconnected
during an active transfer. This occurs because _ep_nuke() returns
requests to the gadget layer without properly unmapping DMA buffers
or cleaning up scatter-gather bounce buffers.
Root cause:
When a disconnect happens during a multi-segment DMA transfer, the
request's num_mapped_sgs field and sgt.sgl pointer remain set with
stale values. The request is returned to the gadget driver with status
-ESHUTDOWN but still has active DMA state. If the gadget driver reuses
this request on reconnect without reinitializing it, the stale DMA
state causes _hardware_enqueue() to skip DMA mapping (seeing non-zero
num_mapped_sgs) and attempt to use freed/invalid DMA addresses,
leading to alignment errors and potential memory corruption.
The normal completion path via _hardware_dequeue() properly calls
usb_gadget_unmap_request_by_dev() and sglist_do_debounce() before
returning the request. The _ep_nuke() path must do the same cleanup
to ensure requests are returned in a clean, reusable state.
Fix:
Add DMA unmapping and bounce buffer cleanup to _ep_nuke() to mirror
the cleanup sequence in _hardware_dequeue():
- Call usb_gadget_unmap_request_by_dev() if num_mapped_sgs is set
- Call sglist_do_debounce() with copy=false if bounce buffer exists
This ensures that when requests are returned due to endpoint shutdown,
they don't retain stale DMA mappings. The 'false' parameter to
sglist_do_debounce() prevents copying data back (appropriate for
shutdown path where transfer was aborted).
Signed-off-by: Mario Peter <mario.peter@leica-geosystems.com>
Reviewed-by: Xu Yang <xu.yang_2@nxp.com>
Acked-by: Peter Chen <peter.chen@kernel.org>
Link: https://patch.msgid.link/20260108165902.795354-1-mario.peter@leica-geosystems.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Currently the wakeup and controller interrupt name are same. It's not
easy to find the correct one in /proc/interrupt at the first glance.
Rename the wakeup interrupt name for better distinction.
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Acked-by: Peter Chen <peter.chen@kernel.org>
Link: https://patch.msgid.link/20260112110408.3263954-1-xu.yang_2@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
If we don't have a usb3 phy we don't need to assert the core resets.
Deassert them even if we didn't assert them to support booting when the
bootloader never released the core from reset.
Signed-off-by: Sean Anderson <sean.anderson@linux.dev>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://patch.msgid.link/20260106171018.501612-1-sean.anderson@linux.dev
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Since <linux/kernel.h> no longer includes <linux/hex.h>, any users
of the hex interfaces need to include <linux/hex.h> themselves, so
add the header file here as needed.
Suggested-by: Stephen Rothwell <sfr@canb.auug.org.au>
Fixes: e065c6a7e46c ("usb: gadget: u_ether: add gether_opts for config caching")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Closes: https://lore.kernel.org/linux-next/2768c835-7ac9-4540-a665-5dd516a80eee@infradead.org/T/#t
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Link: https://patch.msgid.link/20260113071831.4158296-1-rdunlap@infradead.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
It turns out that warning about which USB host controller is loaded
before another one doesn't really matter. All that really is needed is
the PCI softdep module loading logic, which has been present in the
kernel ever since commit 05c92da0c524 ("usb: ohci/uhci - add soft
dependencies on ehci_pci")
So remove the warning messages, they are not useful, not needed, and
only confuse people. As can be seen in the discussion at
https://lore.kernel.org/r/20251230080014.3934590-1-chenhuacai@loongson.cn
Cc: Huacai Chen <chenhuacai@loongson.cn>
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Reviewed-by: Huacai Chen <chenhuacai@loongson.cn>
Link: https://patch.msgid.link/2026010739-diffuser-shelter-e31c@gregkh
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Do dwc3 core auto suspend enable for device and disable for host
, this can make sure dwc3 core device auto suspend setting is
correct all the time, the background of disable dwc3 core device
auto suspend is to make its parent device suspend immediately
(so wakeup enable can be enabled) after xhci-plat device suspended,
for device mode, we keep the dwc3 core device auto suspend is to
give some wait for gadget to be enumerated.
Note: It's a temporary solution until we switch to using the new
flatten model.
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Link: https://patch.msgid.link/20260108081433.2119328-3-xu.yang_2@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
It's confuse to let "dwc3" represent a platform_device, because "dwc3"
may also represent a dwc3 core structure. Rename it for better
distinction.
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Link: https://patch.msgid.link/20260108081433.2119328-2-xu.yang_2@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Call dwc3_pre_set_role() to support both extcon and otg usecase, so that
the glue driver can do proper action in case of role changes.
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Link: https://patch.msgid.link/20260108081433.2119328-1-xu.yang_2@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Currently, DMA_FROM_DEVICE is used when attaching DMABUFs to IN
endpoints and DMA_TO_DEVICE for OUT endpoints. This is inverted from
how it should be.
The result is IOMMU read-only mappings placed on OUT queues,
triggering arm-smmu write faults.
Put differently, OUT endpoints flow data from host -> gadget, meaning
the UDC peripheral needs to have write access to the buffer to fill it
with the incoming data.
This commit flips the directions and updates the implicit-sync helpers
so IN endpoints act as readers and OUT endpoints as writers.
Signed-off-by: Sam Day <me@samcday.com>
Tested-by: David Heidelberg <david@ixit.cz> # OnePlus 6T on sdm845-next-20251119
Link: https://patch.msgid.link/20260108-ffs-dmabuf-ioctl-fix-v1-2-e51633891a81@samcday.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When ffs_epfile_ioctl handles FUNCTIONFS_DMABUF_* ioctls, it's currently
falling through when copy_from_user fails.
However, this fallthrough isn't being checked properly, so the handler
continues executing further than it should. It then tries the secondary
dispatch where it ultimately gives up and returns -ENOTTY.
The end result is invalid ioctl invocations will yield a -ENOTTY rather
than an -EFAULT.
It's a common pattern elsewhere in the kernel code to directly return
-EFAULT when copy_from_user fails. So we update ffs_epfile_ioctl to do
the same and fix this issue.
Signed-off-by: Sam Day <me@samcday.com>
Link: https://patch.msgid.link/20260108-ffs-dmabuf-ioctl-fix-v1-1-e51633891a81@samcday.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
In usbg_submit_command(), which handles the UAS protocol, the 'data_len'
member of the 'usbg_cmd' structure was left uninitialized by the
logic, relying instead on the zeroing performed by usbg_get_cmd().
In contrast, the BOT path (bot_submit_command) explicitly initializes
this field from the Command Block Wrapper (CBW). This discrepancy is
evident in error handling paths where __target_init_cmd() is called
using cmd->data_len.
Explicitly initialize cmd->data_len to 0 in the UAS path and use this
variable when calling target_submit_cmd(). This ensures architectural
consistency between the UAS and BOT protocols within the driver and
avoids reliance on implicit memory state during error transitions.
Signed-off-by: Jiasheng Jiang <jiashengjiangcool@gmail.com>
Link: https://patch.msgid.link/20260107190622.26070-1-jiashengjiangcool@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Move device name initialization to occur after i3c_bus_init()
so that i3cbus->id is guaranteed to be assigned before it is used.
Fixes: 9d4f219807d5 ("i3c: fix refcount inconsistency in i3c_master_register")
Signed-off-by: Billy Tsai <billy_tsai@aspeedtech.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://patch.msgid.link/20260112-upstream_i3c_fix-v1-1-cbbf2cb71809@aspeedtech.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
The Renesas I3C controller does not retain its register state across system
suspend, requiring the driver to explicitly save and restore hardware
configuration.
Add suspend and resume NOIRQ callbacks to handle system sleep transitions.
During suspend, save the Device Address Table (DAT) entries, assert reset
lines, and disable all related clocks to allow the controller to enter a
low-power state.
On resume, re-enable clocks and reset lines in the proper order. Restore
the REFCKCTL register, master dynamic address, and all DAT entries, then
reinitialize the controller.
Store the REFCLK divider value, and the master dynamic address to restore
timing and addressing configuration after resume.
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Tommaso Merciai <tommaso.merciai.xr@bp.renesas.com>
Link: https://patch.msgid.link/c469ef89e0156d37746a85bfc314232847d1185a.1767781092.git.tommaso.merciai.xr@bp.renesas.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
Move the hardware initialization sequence in renesas_i3c_bus_init()
into a dedicated renesas_i3c_hw_init() helper.
Simplify the code and prepare the driver for upcoming suspend/resume
support.
No functional change intended.
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Tommaso Merciai <tommaso.merciai.xr@bp.renesas.com>
Link: https://patch.msgid.link/795327270a6ceb23e15513a2619a19ae4876cfba.1767781092.git.tommaso.merciai.xr@bp.renesas.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
