summaryrefslogtreecommitdiff
path: root/drivers
AgeCommit message (Collapse)Author
2025-06-11net/mdiobus: Fix potential out-of-bounds clause 45 read/write accessJakub Raczynski
When using publicly available tools like 'mdio-tools' to read/write data from/to network interface and its PHY via C45 (clause 45) mdiobus, there is no verification of parameters passed to the ioctl and it accepts any mdio address. Currently there is support for 32 addresses in kernel via PHY_MAX_ADDR define, but it is possible to pass higher value than that via ioctl. While read/write operation should generally fail in this case, mdiobus provides stats array, where wrong address may allow out-of-bounds read/write. Fix that by adding address verification before C45 read/write operation. While this excludes this access from any statistics, it improves security of read/write operation. Fixes: 4e4aafcddbbf ("net: mdio: Add dedicated C45 API to MDIO bus drivers") Signed-off-by: Jakub Raczynski <j.raczynski@samsung.com> Reported-by: Wenjing Shan <wenjing.shan@samsung.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2025-06-11net/mdiobus: Fix potential out-of-bounds read/write accessJakub Raczynski
When using publicly available tools like 'mdio-tools' to read/write data from/to network interface and its PHY via mdiobus, there is no verification of parameters passed to the ioctl and it accepts any mdio address. Currently there is support for 32 addresses in kernel via PHY_MAX_ADDR define, but it is possible to pass higher value than that via ioctl. While read/write operation should generally fail in this case, mdiobus provides stats array, where wrong address may allow out-of-bounds read/write. Fix that by adding address verification before read/write operation. While this excludes this access from any statistics, it improves security of read/write operation. Fixes: 080bb352fad00 ("net: phy: Maintain MDIO device and bus statistics") Signed-off-by: Jakub Raczynski <j.raczynski@samsung.com> Reported-by: Wenjing Shan <wenjing.shan@samsung.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2025-06-11spi: spi-mt65xx: Add support for MT6991 Dimensity 9400 SPI IPMAngeloGioacchino Del Regno
Add support for the SPI IPM controller found in the MediaTek Dimensity 9400 (MT6991) SoC. As a note, this is the same SPI IPM Controller IP found on the MT8196 Kompanio counterpart. Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Link: https://patch.msgid.link/20250611110747.458090-2-angelogioacchino.delregno@collabora.com Signed-off-by: Mark Brown <broonie@kernel.org>
2025-06-11regulator: rpi-panel-v2: Fix missing OF dependencyMarek Vasut
Add missing OF dependency and drop of_match_ptr() use. This fixes the following LKP report: " >> drivers/regulator/rpi-panel-v2-regulator.c:95:34: warning: 'rpi_panel_v2_dt_ids' defined but not used [-Wunused-const-variable=] static const struct of_device_id rpi_panel_v2_dt_ids[] = { ^~~~~~~~~~~~~~~~~~~ " Fixes: d49305862fdc ("regulator: rpi-panel-v2: Add regulator for 7" Raspberry Pi 720x1280") Reported-by: kernel test robot <lkp@intel.com> Closes: https://lore.kernel.org/oe-kbuild-all/202506100440.fyTGO7CG-lkp@intel.com/ Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org> Link: https://patch.msgid.link/20250609223012.87764-1-marek.vasut+renesas@mailbox.org Signed-off-by: Mark Brown <broonie@kernel.org>
2025-06-11regulator: bd718x7: Clarify comment by moving itMatti Vaittinen
The BD718x7 needs to disable voltage monitoring for a duration of certain voltage changes. The comment explaining use of msleep(1) instead of a more accurate delay(), was placed to a function which disabled the protection. The actual sleeping is done in a different place of the code, after the voltage has been changed. Browsing through the comment and code after the years made me to scratch my head for a second. I may have figured why me and so many fellow developers are slowly getting bald. Clarify things a bit and move the comment about required delay directly above the sleep. Leave only a small comment explaining why the protection is disabled to the spot where the logic for disabling is. Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com> Link: https://patch.msgid.link/a90cb77e66a253f4055bbb99672dc81c7457de66.1749533040.git.mazziesaccount@gmail.com Signed-off-by: Mark Brown <broonie@kernel.org>
2025-06-11udmabuf: use sgtable-based scatterlist wrappersMarek Szyprowski
Use common wrappers operating directly on the struct sg_table objects to fix incorrect use of scatterlists sync calls. dma_sync_sg_for_*() functions have to be called with the number of elements originally passed to dma_map_sg_*() function, not the one returned in sgtable's nents. Fixes: 1ffe09590121 ("udmabuf: fix dma-buf cpu access") CC: stable@vger.kernel.org Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com> Acked-by: Vivek Kasireddy <vivek.kasireddy@intel.com> Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Christian König <christian.koenig@amd.com> Link: https://lore.kernel.org/r/20250507160913.2084079-3-m.szyprowski@samsung.com
2025-06-11drm/ttm: Should to return the evict errorEmily Deng
For the evict fail case, the evict error should be returned. v2: Consider ENOENT case. v3: Abort directly when the eviction failed for some reason (except for -ENOENT) and not wait for the move to finish Signed-off-by: Emily Deng <Emily.Deng@amd.com> Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Christian König <christian.koenig@amd.com> Link: https://lore.kernel.org/r/20250603091154.3472646-1-Emily.Deng@amd.com
2025-06-11drm/i915/display: drop i915_reg.h include where possibleJani Nikula
A number of files have unnecessary i915_reg.h includes. Drop them. Reviewed-by: Michał Grzelak <michal.grzelak@intel.com> Link: https://lore.kernel.org/r/7c4002322f4d8132fd2eaa1a4d688539cdd043c3.1749469962.git.jani.nikula@intel.com Signed-off-by: Jani Nikula <jani.nikula@intel.com>
2025-06-11drm/i915/display: include intel_display_reg_defs.h from display regs filesJani Nikula
Some display register files include i915_reg_defs.h, some don't include anything. Prefer intel_display_reg_defs.h in display. Reviewed-by: Michał Grzelak <michal.grzelak@intel.com> Link: https://lore.kernel.org/r/06c24e1f6a7a2f6b4801b0a079eec3cc924402a7.1749469962.git.jani.nikula@intel.com Signed-off-by: Jani Nikula <jani.nikula@intel.com>
2025-06-11Revert "drm/xe/display: use xe->display to decide whether to do anything"Vivek Kasireddy
This reverts commit 5a9f299f956ef9764f56044cfca7aafa23cea1d1. The following crash/regression was seen with the reverted commit on a specific BMG SKU with no display capabilities: [ 115.582833] BUG: kernel NULL pointer dereference, address: 00000000000005d0 [ 115.589775] #PF: supervisor write access in kernel mode [ 115.594976] #PF: error_code(0x0002) - not-present page [ 115.600088] PGD 0 P4D 0 [ 115.602617] Oops: Oops: 0002 [#1] SMP [ 115.606267] CPU: 14 UID: 0 PID: 1547 Comm: kworker/14:3 Tainted: G U E 6.15.0-local+ #62 PREEMPT(voluntary) [ 115.617332] Tainted: [U]=USER, [E]=UNSIGNED_MODULE [ 115.622100] Hardware name: Intel Corporation Meteor Lake Client Platform/MTL-P DDR5 SODIMM SBS RVP, BIOS MTLPEMI1.R00.3471.D49.2401260852 01/26/2024 [ 115.635314] Workqueue: pm pm_runtime_work [ 115.639309] RIP: 0010:_raw_spin_lock+0x17/0x30 [ 115.662382] RSP: 0018:ffffd13f82e7bc30 EFLAGS: 00010246 [ 115.667581] RAX: 0000000000000000 RBX: ffff8be919076000 RCX: 0000000000000002 [ 115.674675] RDX: 0000000000000001 RSI: 000000000000004b RDI: 00000000000005d0 [ 115.681775] RBP: ffffd13f82e7bc60 R08: ffffd13f82e7bb00 R09: ffff8beb0c1b06c0 [ 115.688869] R10: ffff8be7c034f4c0 R11: fefefefefefefeff R12: fffffffffffffff0 [ 115.695965] R13: ffff8be9190762e8 R14: ffff8be919077798 R15: 00000000000005d0 [ 115.703062] FS: 0000000000000000(0000) GS:ffff8beb552b6000(0000) knlGS:0000000000000000 [ 115.711106] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 115.716826] CR2: 00000000000005d0 CR3: 000000024c68d002 CR4: 0000000000f72ef0 [ 115.723921] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 [ 115.731015] DR3: 0000000000000000 DR6: 00000000ffff07f0 DR7: 0000000000000400 [ 115.738113] PKRU: 55555554 [ 115.740816] Call Trace: [ 115.743258] <TASK> [ 115.745363] ? xe_display_flush_cleanup_work+0x92/0x120 [xe] [ 115.751102] xe_display_pm_runtime_suspend+0x42/0x80 [xe] [ 115.756542] xe_pm_runtime_suspend+0x11b/0x1b0 [xe] [ 115.761463] xe_pci_runtime_suspend+0x23/0xd0 [xe] [ 115.766291] pci_pm_runtime_suspend+0x6b/0x1a0 [ 115.770717] ? pci_pm_thaw_noirq+0xa0/0xa0 [ 115.774797] __rpm_callback+0x48/0x1e0 [ 115.778531] ? pci_pm_thaw_noirq+0xa0/0xa0 [ 115.782614] rpm_callback+0x66/0x70 [ 115.786090] ? pci_pm_thaw_noirq+0xa0/0xa0 [ 115.790173] rpm_suspend+0xe1/0x5e0 [ 115.793647] ? psi_task_switch+0xb8/0x200 [ 115.797643] ? finish_task_switch.isra.0+0x8d/0x270 [ 115.802502] pm_runtime_work+0xa6/0xc0 [ 115.806238] process_one_work+0x186/0x350 [ 115.810234] worker_thread+0x33a/0x480 [ 115.813968] ? process_one_work+0x350/0x350 [ 115.818132] kthread+0x10c/0x220 [ 115.821350] ? kthreads_online_cpu+0x120/0x120 [ 115.825774] ret_from_fork+0x3a/0x60 [ 115.829339] ? kthreads_online_cpu+0x120/0x120 [ 115.833768] ret_from_fork_asm+0x11/0x20 [ 115.829339] ? kthreads_online_cpu+0x120/0x120 [ 115.833768] ret_from_fork_asm+0x11/0x20 [ 115.837680] </TASK> [ 115.839907] acpi_tad(E) drm(E) [ 115.931629] CR2: 00000000000005d0 [ 115.934935] ---[ end trace 0000000000000000 ]--- [ 115.939531] RIP: 0010:_raw_spin_lock+0x17/0x30 We cannot yet use xe->display to determine whether display hardware has been successfully probed/initialized or not. This is because xe->display would not be set to NULL even with GPUs with no display capabilities (e.g, GMD_ID_DISPLAY = 0). However, this might change in the future as Xe and i915 code is unified to deal with no display cases. Therefore, for now we have to continue to rely on xe->info.probe_display (which would be set to false with display-less GPUs) to decide whether to invoke any display related functions or not. Cc: Jani Nikula <jani.nikula@intel.com> Cc: Matt Roper <matthew.d.roper@intel.com> Cc: Lucas De Marchi <lucas.demarchi@intel.com> Signed-off-by: Vivek Kasireddy <vivek.kasireddy@intel.com> Reviewed-by: Jani Nikula <jani.nikula@intel.com> Link: https://lore.kernel.org/r/20250605054247.386633-1-vivek.kasireddy@intel.com Signed-off-by: Jani Nikula <jani.nikula@intel.com>
2025-06-11ata: ahci: Use correct BIOS build date for ThinkPad W541 quirkNiklas Cassel
Fix the TODO in ahci_broken_lpm() by using the proper BIOS build date. The proper BIOS build date was provided by Hans, see Link. Link: https://lore.kernel.org/linux-ide/6ea509c8-b38d-4941-8a29-c1117ff3dd5b@redhat.com/ Reviewed-by: Damien Le Moal <dlemoal@kernel.org> Reviewed-by: Hans de Goede <hansg@kernel.org> Link: https://lore.kernel.org/r/20250610110757.1318959-6-cassel@kernel.org Signed-off-by: Niklas Cassel <cassel@kernel.org>
2025-06-11ata: pata_macio: Fix PCI region leakPhilipp Stanner
pci_request_regions() became a managed devres functions if the PCI device was enabled with pcim_enable_device(), which is the case for pata_macio. The PCI subsystem recently removed this hybrid feature from pci_request_region(). When doing so, pata_macio was forgotten to be ported to use pcim_request_all_regions(). If that function is not used, pata_macio will fail on driver-reload because the PCI regions will remain blocked. Fix the region leak by replacing pci_request_regions() with its managed counterpart, pcim_request_all_regions(). Fixes: 51f6aec99cb0 ("PCI: Remove hybrid devres nature from request functions") Signed-off-by: Philipp Stanner <phasta@kernel.org> Reviewed-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com> Reviewed-by: Damien Le Moal <dlemoal@kernel.org> Link: https://lore.kernel.org/r/20250610135413.35930-2-phasta@kernel.org Signed-off-by: Niklas Cassel <cassel@kernel.org>
2025-06-11dma-buf: fix compare in WARN_ON_ONCEChristian König
Smatch pointed out this trivial typo: drivers/dma-buf/dma-buf.c:1123 dma_buf_map_attachment() warn: passing positive error code '16' to 'ERR_PTR' drivers/dma-buf/dma-buf.c 1113 dma_resv_assert_held(attach->dmabuf->resv); 1114 1115 if (dma_buf_pin_on_map(attach)) { 1116 ret = attach->dmabuf->ops->pin(attach); 1117 /* 1118 * Catch exporters making buffers inaccessible even when 1119 * attachments preventing that exist. 1120 */ 1121 WARN_ON_ONCE(ret == EBUSY); ^^^^^ This was probably intended to be -EBUSY? 1122 if (ret) --> 1123 return ERR_PTR(ret); ^^^ Otherwise we will eventually crash. 1124 } 1125 1126 sg_table = attach->dmabuf->ops->map_dma_buf(attach, direction); 1127 if (!sg_table) 1128 sg_table = ERR_PTR(-ENOMEM); 1129 if (IS_ERR(sg_table)) 1130 goto error_unpin; 1131 Signed-off-by: Christian König <christian.koenig@amd.com> Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@igalia.com> Link: https://lore.kernel.org/r/20250605085336.62156-1-christian.koenig@amd.com
2025-06-11Merge tag 'ath-current-20250608' of ↵Johannes Berg
git://git.kernel.org/pub/scm/linux/kernel/git/ath/ath Jeff Johnson says: ================== ath.git updates for v6.16-rc2 Fix a handful of both build and stability issues across multiple drivers. ================== Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2025-06-11wifi: iwlwifi: fix merge damage related to iwl_pci_resumeEmmanuel Grumbach
The changes I made in wifi: iwlwifi: don't warn if the NIC is gone in resume conflicted with a major rework done in this area. The merge de-facto removed my changes. Re-add them. Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Link: https://patch.msgid.link/20250603091754.70182-1-emmanuel.grumbach@intel.com Fixes: 06c4b2036818 ("Merge tag 'iwlwifi-next-2025-05-15' of https://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next") Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2025-06-11Revert "wifi: mwifiex: Fix HT40 bandwidth issue."Francesco Dolcini
This reverts commit 4fcfcbe45734 ("wifi: mwifiex: Fix HT40 bandwidth issue.") That commit introduces a regression, when HT40 mode is enabled, received packets are lost, this was experience with W8997 with both SDIO-UART and SDIO-SDIO variants. From an initial investigation the issue solves on its own after some time, but it's not clear what is the reason. Given that this was just a performance optimization, let's revert it till we have a better understanding of the issue and a proper fix. Cc: Jeff Chen <jeff.chen_1@nxp.com> Cc: stable@vger.kernel.org Fixes: 4fcfcbe45734 ("wifi: mwifiex: Fix HT40 bandwidth issue.") Closes: https://lore.kernel.org/all/20250603203337.GA109929@francesco-nb/ Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com> Link: https://patch.msgid.link/20250605130302.55555-1-francesco@dolcini.it [fix commit reference format] Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2025-06-11HID: multitouch: add device ID for Apple Touch BarKerem Karabay
This patch adds the device ID of Apple Touch Bar found on x86 MacBook Pros to the hid-multitouch driver. Note that this is device ID is for T2 Macs. Testing on T1 Macs would be appreciated. Signed-off-by: Kerem Karabay <kekrby@gmail.com> Co-developed-by: Aditya Garg <gargaditya08@live.com> Signed-off-by: Aditya Garg <gargaditya08@live.com> Signed-off-by: Jiri Kosina <jkosina@suse.com>
2025-06-11HID: multitouch: specify that Apple Touch Bar is directKerem Karabay
Currently the driver determines the device type based on the application, but this value is not reliable on Apple Touch Bar, where the application is HID_DG_TOUCHPAD even though this device is direct, so add a quirk for the same. Acked-by: Benjamin Tissoires <bentiss@kernel.org> Signed-off-by: Kerem Karabay <kekrby@gmail.com> Co-developed-by: Aditya Garg <gargaditya08@live.com> Signed-off-by: Aditya Garg <gargaditya08@live.com> Signed-off-by: Jiri Kosina <jkosina@suse.com>
2025-06-11HID: multitouch: take cls->maxcontacts into account for Apple Touch Bar even ↵Kerem Karabay
without a HID_DG_CONTACTMAX field In Apple Touch Bar, the HID_DG_CONTACTMAX is not present, but the maximum contact count is still greater than the default. Add quirks for the same. Acked-by: Benjamin Tissoires <bentiss@kernel.org> Signed-off-by: Kerem Karabay <kekrby@gmail.com> Co-developed-by: Aditya Garg <gargaditya08@live.com> Signed-off-by: Aditya Garg <gargaditya08@live.com> Signed-off-by: Jiri Kosina <jkosina@suse.com>
2025-06-11HID: multitouch: support getting the tip state from HID_DG_TOUCH fields in ↵Kerem Karabay
Apple Touch Bar In Apple Touch Bar, the tip state is contained in fields with the HID_DG_TOUCH usage. This feature is gated by a quirk in order to prevent breaking other devices, see commit c2ef8f21ea8f ("HID: multitouch: add support for trackpads"). Acked-by: Benjamin Tissoires <bentiss@kernel.org> Signed-off-by: Kerem Karabay <kekrby@gmail.com> Co-developed-by: Aditya Garg <gargaditya08@live.com> Signed-off-by: Aditya Garg <gargaditya08@live.com> Signed-off-by: Jiri Kosina <jkosina@suse.com>
2025-06-11HID: multitouch: Get the contact ID from HID_DG_TRANSDUCER_INDEX fields in ↵Kerem Karabay
case of Apple Touch Bar In Apple Touch Bar, the contact ID is contained in fields with the HID_DG_TRANSDUCER_INDEX usage rather than HID_DG_CONTACTID, thus differing from the HID spec. Add a quirk for the same. Acked-by: Benjamin Tissoires <bentiss@kernel.org> Signed-off-by: Kerem Karabay <kekrby@gmail.com> Co-developed-by: Aditya Garg <gargaditya08@live.com> Signed-off-by: Aditya Garg <gargaditya08@live.com> Signed-off-by: Jiri Kosina <jkosina@suse.com>
2025-06-11macsec: MACsec SCI assignment for ES = 0Carlos Fernandez
According to 802.1AE standard, when ES and SC flags in TCI are zero, used SCI should be the current active SC_RX. Current code uses the header MAC address. Without this patch, when ES flag is 0 (using a bridge or switch), header MAC will not fit the SCI and MACSec frames will be discarted. In order to test this issue, MACsec link should be stablished between two interfaces, setting SC and ES flags to zero and a port identifier different than one. For example, using ip macsec tools: ip link add link $ETH0 macsec0 type macsec port 11 send_sci off end_station off ip macsec add macsec0 tx sa 0 pn 2 on key 01 $ETH1_KEY ip macsec add macsec0 rx port 11 address $ETH1_MAC ip macsec add macsec0 rx port 11 address $ETH1_MAC sa 0 pn 2 on key 02 ip link set dev macsec0 up ip link add link $ETH1 macsec1 type macsec port 11 send_sci off end_station off ip macsec add macsec1 tx sa 0 pn 2 on key 01 $ETH0_KEY ip macsec add macsec1 rx port 11 address $ETH0_MAC ip macsec add macsec1 rx port 11 address $ETH0_MAC sa 0 pn 2 on key 02 ip link set dev macsec1 up Fixes: c09440f7dcb3 ("macsec: introduce IEEE 802.1AE driver") Co-developed-by: Andreu Montiel <Andreu.Montiel@technica-engineering.de> Signed-off-by: Andreu Montiel <Andreu.Montiel@technica-engineering.de> Signed-off-by: Carlos Fernandez <carlos.fernandez@technica-engineering.de> Reviewed-by: Subbaraya Sundeep <sbhatta@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2025-06-11drm/i915/panel: sync panel prepared state at registerJani Nikula
If the panel is enabled at probe, and we take over the hardware state, the drm_panel prepared state will be out of sync. We'll need to notify drm_panel framework about the state at probe, so it can in turn notify the panel followers. Cc: Lee Shawn C <shawn.c.lee@intel.com> Tested-by: Lee Shawn C <shawn.c.lee@intel.com> Reviewed-by: Arun R Murthy <arun.r.murthy@intel.com> Reviewed-by: Maxime Ripard <mripard@kernel.org> Link: https://lore.kernel.org/r/a33e4fe5e9970aed9c4aef8c426c00a189149c32.1749199013.git.jani.nikula@intel.com Signed-off-by: Jani Nikula <jani.nikula@intel.com>
2025-06-11drm/i915/panel: register drm_panel and call prepare/unprepare for ICL+ DSIJani Nikula
Allocate and register a drm_panel so that drm_panel_followers can find the panel. Pass the drm_connector::kdev device to drm_panel allocation for matching. That's only available after drm_sysfs_connector_add(), so we need to postpone the drm_panel allocation until .late_register() hook. The drm_panel framework is moving towards devm_drm_panel_alloc(). It requires a wrapper struct, and struct intel_panel would be the natural candidate. However, we can't postpone its allocation until .late_register(), so we have to use __devm_drm_panel_alloc() directly for now. Call the drm_panel_prepare() and drm_panel_unprepare() functions for ICL+ DSI, so that followers get notified of the panel power state changes. This can later be expanded to VLV+ DSI and eDP. Cc: Maxime Ripard <mripard@kernel.org> Cc: Heikki Krogerus <heikki.krogerus@linux.intel.com> Cc: Lee Shawn C <shawn.c.lee@intel.com> Tested-by: Lee Shawn C <shawn.c.lee@intel.com> Reviewed-by: Maxime Ripard <mripard@kernel.org> Link: https://lore.kernel.org/r/13d15c1414e65ffb21944d66e2820befdab54e98.1749199013.git.jani.nikula@intel.com Signed-off-by: Jani Nikula <jani.nikula@intel.com>
2025-06-11drm/i915/panel: add panel register/unregisterJani Nikula
Add panel register/unregister functions, and handle backlight register/unregister from there. This is in preparation for adding more panel specific register/unregister functionality. Cc: Lee Shawn C <shawn.c.lee@intel.com> Tested-by: Lee Shawn C <shawn.c.lee@intel.com> Reviewed-by: Arun R Murthy <arun.r.murthy@gmail.com> Reviewed-by: Maxime Ripard <mripard@kernel.org> Link: https://lore.kernel.org/r/b737d4bc8b91df630cd4db4648f3a3571989cfd8.1749199013.git.jani.nikula@intel.com Signed-off-by: Jani Nikula <jani.nikula@intel.com>
2025-06-11drm/sitronix: st7571-i2c: Select VIDEOMODE_HELPERSNathan Chancellor
This driver requires of_get_display_timing() from CONFIG_VIDEOMODE_HELPERS but does not select it. If no other driver selects it, there will be a failure from the linker if the driver is built in or modpost if it is a module. ERROR: modpost: "of_get_display_timing" [drivers/gpu/drm/sitronix/st7571-i2c.ko] undefined! Select CONFIG_VIDEOMODE_HELPERS to resolve the build failure. Fixes: 4b35f0f41ee2 ("drm/st7571-i2c: add support for Sitronix ST7571 LCD controller") Signed-off-by: Nathan Chancellor <nathan@kernel.org> Link: https://lore.kernel.org/r/20250610-drm-st7571-i2c-select-videomode-helpers-v1-1-d30b50ff6e64@kernel.org Signed-off-by: Maxime Ripard <mripard@kernel.org>
2025-06-11platform/x86: ideapad: Expose charge_typesJelle van der Waa
Some Ideapad models support a battery conservation mode which limits the battery charge threshold for longer battery longevity. This is currently exposed via a custom conservation_mode attribute in sysfs. The newly introduced charge_types sysfs attribute is a standardized replacement for laptops with a fixed end charge threshold. Setting it to `Long Life` would enable battery conservation mode. The standardized user space API would allow applications such as UPower to detect laptops which support this battery longevity mode and set it. Tested on an Lenovo ideapad U330p. Signed-off-by: Jelle van der Waa <jvanderwaa@redhat.com> Suggested-By: Hans de Goede <hdegoede@redhat.com> Reviewed-by: Thomas Weißschuh <linux@weissschuh.net> Reviewed-by: Armin Wolf <W_Armin@gmx.de> Link: https://lore.kernel.org/r/20250514201054.381320-1-jvanderwaa@redhat.com Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
2025-06-11pinctrl: lynxpoint: use new GPIO line value setter callbacksBartosz Golaszewski
struct gpio_chip now has callbacks for setting line values that return an integer, allowing to indicate failures. Convert the driver to using them. Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
2025-06-11pinctrl: intel: use new GPIO line value setter callbacksBartosz Golaszewski
struct gpio_chip now has callbacks for setting line values that return an integer, allowing to indicate failures. Convert the driver to using them. Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
2025-06-11pinctrl: cherryview: use new GPIO line value setter callbacksBartosz Golaszewski
struct gpio_chip now has callbacks for setting line values that return an integer, allowing to indicate failures. Convert the driver to using them. Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
2025-06-11pinctrl: baytrail: use new GPIO line value setter callbacksBartosz Golaszewski
struct gpio_chip now has callbacks for setting line values that return an integer, allowing to indicate failures. Convert the driver to using them. Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
2025-06-11drm/panel: use fwnode based lookups for panel followersJani Nikula
Use firmware node based lookups for panel followers, to make the code independent of OF and device tree, and make it work also for ACPI with an appropriate _DSD. ASL example: Package (0x02) { "panel", \_SB.PCI0.GFX0.LCD0 } v2: - Update comments (Doug, Arun) - s/IS_ERR_OR_NULL/IS_ERR/ (Doug) Suggested-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Cc: Neil Armstrong <neil.armstrong@linaro.org> Cc: Jessica Zhang <jessica.zhang@oss.qualcomm.com> Cc: Maxime Ripard <mripard@kernel.org> Cc: Doug Anderson <dianders@chromium.org> Cc: Lee Shawn C <shawn.c.lee@intel.com> Tested-by: Lee Shawn C <shawn.c.lee@intel.com> Reviewed-by: Douglas Anderson <dianders@chromium.org> Tested-by: Douglas Anderson <dianders@chromium.org> Reviewed-by: Arun R Murthy <arun.r.murthy@intel.com> Acked-by: Maxime Ripard <mripard@kernel.org> Link: https://lore.kernel.org/r/20250610094132.3240567-1-jani.nikula@intel.com Signed-off-by: Jani Nikula <jani.nikula@intel.com>
2025-06-11platform/x86: Move Lenovo files into lenovo subdirMark Pearson
Create lenovo subdirectory for holding Lenovo specific drivers. Signed-off-by: Mark Pearson <mpearson-lenovo@squebb.ca> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Link: https://lore.kernel.org/r/20250610192830.1731454-2-mpearson-lenovo@squebb.ca [ij: put depends on DMI back, fix trailing empty lines.] Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
2025-06-11platform/x86: thinklmi: improved DMI handlingMark Pearson
Fix issues reported by kernel test robot. - Require DMI for think-lmi. - Check return from getting serial string Reported-by: kernel test robot <lkp@intel.com> Closes: https://lore.kernel.org/oe-kbuild-all/202506062319.F0IpDxF6-lkp@intel.com/ Signed-off-by: Mark Pearson <mpearson-lenovo@squebb.ca> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Link: https://lore.kernel.org/r/20250610192830.1731454-1-mpearson-lenovo@squebb.ca Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
2025-06-11platform/x86: intel_telemetry: Remove unused telemetry_raw_read_events()Dr. David Alan Gilbert
telemetry_raw_read_events() was added by the commit 378f956e3f93 ("platform/x86: Add Intel Telemetry Core Driver") in 2016 but has remained unused. Remove it. Signed-off-by: Dr. David Alan Gilbert <linux@treblig.org> Link: https://lore.kernel.org/r/20250608012512.377134-4-linux@treblig.org Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
2025-06-11platform/x86: intel_telemetry: Remove unused telemetry_[gs]et_sampling_period()Dr. David Alan Gilbert
The functions: - telemetry_get_sampling_period() - telemetry_set_sampling_period() were both added by the commit 378f956e3f93 ("platform/x86: Add Intel Telemetry Core Driver") in 2016 but have remained unused. They're each a tiny wrapper that is the only caller through a similarly named function pointer, and for each function pointer there's a 'def' empty implementation and a plt implementation. Remove all of those components for each function. Signed-off-by: Dr. David Alan Gilbert <linux@treblig.org> Link: https://lore.kernel.org/r/20250608012512.377134-3-linux@treblig.org Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
2025-06-11platform/x86: intel_telemetry: Remove unused telemetry_*_events()Dr. David Alan Gilbert
The functions: - telemetry_add_events() - telemetry_update_events() - telemetry_reset_events() - telemetry_get_eventconfig() were all added by the commit 378f956e3f93 ("platform/x86: Add Intel Telemetry Core Driver") in 2016 but have remained unused. They're each a tiny wrapper that is the only caller through a similarly named function pointer, and for each function pointer there's a 'def' empty implementation and a plt implementation. Remove all of those components for each function. Signed-off-by: Dr. David Alan Gilbert <linux@treblig.org> Link: https://lore.kernel.org/r/20250608012512.377134-2-linux@treblig.org Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
2025-06-11drm/arm/hdlcd: Replace struct simplefb_format with custom typeThomas Zimmermann
Map DRM FourCC codes to pixel descriptions with an internal struct type. Avoid simplefb's struct simplefb_format, which is for parsing "simple-framebuffer" DT nodes. Drop the unsupported formats with alpha channel from the list. The HDLCD drivers uses struct simplefb_format and its default initializer SIMPLEFB_FORMATS to map DRM_FORMAT_ constants to pixel descriptions. The simplefb helpers are for parsing "simple-framebuffer" DT nodes and should be avoided in other context. Therefore replace it in hdlcd with a custom struct type and pixel descriptions from PIXEL_FORMAT_ constants. This change also removes including <linux/platform_data/simplefb.h>, which includes several unrelated headers, such as <linux/fb.h>. v2: - drop unsupported alpha formats (Liviu) - keep original sorting of formats (Javier) - use anonymous type for supported_formats Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de> Reviewed-by: Javier Martinez Canillas <javierm@redhat.com> Reviewed-by: Liviu Dudau <liviu.dudau@arm.com> Link: https://lore.kernel.org/r/20250610073027.322944-1-tzimmermann@suse.de
2025-06-11Merge drm/drm-next into drm-misc-nextThomas Zimmermann
Backmerging to forward to v6.16-rc1 Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
2025-06-11wifi: iwlwifi: move iwl-context-info header filesMiri Korenblit
context info is PCIE specific, so it should be located in pcie directory. The c files are already there, move also the header files. Reviewed-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com> Link: https://patch.msgid.link/20250609211928.606f48f72bcd.I4b89d373d961146e5369d1aed9f625150de7bf7d@changeid
2025-06-11wifi: iwlwifi: pcie: add missing TOP reset codeJohannes Berg
The TOP reset requires code to handle the interrupt, which had been in my patch at some point, but clearly got lost. As the test had been running on the wrong hardware and failing due to that, we missed this. Add the missing code. Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com> Link: https://patch.msgid.link/20250609211928.3f84eb03cc00.If138ceeb8bb178b3931d96b537f746346227e681@changeid
2025-06-11wifi: iwlwifi: mld: respect AUTO_EML_ENABLE in iwl_mld_int_mlo_scan()Itamar Shalev
Respect this flag and don't scan for another link if it is set. Signed-off-by: Itamar Shalev <itamar.shalev@intel.com> Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com> Link: https://patch.msgid.link/20250609211928.9ecb5c5301d4.I88b37e93d9ba66d4381f4976541b4aca2a20e36e@changeid
2025-06-11wifi: iwlwifi: mld: respect AUTO_EML_ENABLE in iwl_mld_retry_emlsr()Daniel Gabay
Respect this flag before initiating MLO scan. Signed-off-by: Daniel Gabay <daniel.gabay@intel.com> Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Reviewed-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com> Link: https://patch.msgid.link/20250609211928.b5c7fbdcb15c.Iaa176c49142b46b0b896728005357faec6a55fa6@changeid
2025-06-11wifi: iwlwifi: mld: remove unneeded compilationsMiri Korenblit
Those are internal files so they should not be compiled. Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com> Link: https://patch.msgid.link/20250609211928.3bfe5222fe79.I1ebd746b0c513e278d231b5c48f5438ca9b9231f@changeid
2025-06-10clk: qcom: camcc-sc8180x: Add SC8180X camera clock controller driverSatya Priya Kakitapalli
Add support for the camera clock controller for camera clients to be able to request for camcc clocks on SC8180X platform. Reviewed-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org> Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com> Signed-off-by: Satya Priya Kakitapalli <quic_skakitap@quicinc.com> Link: https://lore.kernel.org/r/20250512-sc8180x-camcc-support-v4-3-8fb1d3265f52@quicinc.com Signed-off-by: Bjorn Andersson <andersson@kernel.org>
2025-06-10clk: qcom: dispcc-sm8750: Fix setting rate byte and pixel clocksKrzysztof Kozlowski
On SM8750 the setting rate of pixel and byte clocks, while the parent DSI PHY PLL, fails with: disp_cc_mdss_byte0_clk_src: rcg didn't update its configuration. DSI PHY PLL has to be unprepared and its "PLL Power Down" bits in CMN_CTRL_0 asserted. Mark these clocks with CLK_OPS_PARENT_ENABLE to ensure the parent is enabled during rate changes. Cc: stable@vger.kernel.org Fixes: f1080d8dab0f ("clk: qcom: dispcc-sm8750: Add SM8750 Display clock controller") Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com> Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com> Link: https://lore.kernel.org/r/20250520090741.45820-2-krzysztof.kozlowski@linaro.org Signed-off-by: Bjorn Andersson <andersson@kernel.org>
2025-06-10clk: qcom: gcc-ipq8074: fix broken freq table for nss_port6_tx_clk_srcChristian Marangi
With the conversion done by commit e88f03230dc0 ("clk: qcom: gcc-ipq8074: rework nss_port5/6 clock to multiple conf") a Copy-Paste error was made for the nss_port6_tx_clk_src frequency table. This was caused by the wrong setting of the parent in ftbl_nss_port6_tx_clk_src that was wrongly set to P_UNIPHY1_RX instead of P_UNIPHY2_TX. This cause the UNIPHY2 port to malfunction when it needs to be scaled to higher clock. The malfunction was observed with the example scenario with an Aquantia 10G PHY connected and a speed higher than 1G (example 2.5G) Fix the broken frequency table to restore original functionality. Cc: stable@vger.kernel.org Fixes: e88f03230dc0 ("clk: qcom: gcc-ipq8074: rework nss_port5/6 clock to multiple conf") Signed-off-by: Christian Marangi <ansuelsmth@gmail.com> Tested-by: Robert Marko <robimarko@gmail.com> Link: https://lore.kernel.org/r/20250522202600.4028-1-ansuelsmth@gmail.com Signed-off-by: Bjorn Andersson <andersson@kernel.org>
2025-06-10clk: qcom: videocc: Use HW_CTRL_TRIGGER flag for video GDSC'sTaniya Das
The video driver will be using the newly introduced dev_pm_genpd_set_hwmode() API to switch the video GDSC to HW and SW control modes at runtime. Hence use HW_CTRL_TRIGGER flag instead of HW_CTRL for video GDSC's for Qualcomm SoC SC7180, SDM845, SM7150, SM8150 and SM8450. Signed-off-by: Taniya Das <quic_tdas@quicinc.com> Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Reviewed-by: Vikash Garodia <quic_vgarodia@quicinc.com> Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org> Signed-off-by: Renjiang Han <quic_renjiang@quicinc.com> Link: https://lore.kernel.org/r/20250530-switch_gdsc_mode-v5-1-657c56313351@quicinc.com Signed-off-by: Bjorn Andersson <andersson@kernel.org>
2025-06-10remoteproc: qcom: pas: Conclude the rename from adspBjorn Andersson
The change that renamed the driver from "adsp" to "pas" didn't change any of the implementation. The result is an aesthetic eyesore, and confusing to many. Conclude the rename of the driver, by updating function, structures and variable names to match what the driver actually is. The "Hexagon v5" is also dropped from the name and Kconfig, as this isn't correct either. No functional change. Fixes: 9e004f97161d ("remoteproc: qcom: Rename Hexagon v5 PAS driver") Signed-off-by: Bjorn Andersson <bjorn.andersson@oss.qualcomm.com> Reviewed-by: Wasim Nazir <quic_wasimn@quicinc.com> Link: https://lore.kernel.org/r/20250605-pas-rename-v2-1-f1c89e49e691@oss.qualcomm.com Signed-off-by: Bjorn Andersson <andersson@kernel.org>
2025-06-11platform/chrome: cros_ec_typec: Defer probe on missing EC parentTomasz Michalec
If cros_typec_probe is called before EC device is registered, cros_typec_probe will fail. It may happen when cros-ec-typec.ko is loaded before EC bus layer module (e.g. cros_ec_lpcs.ko, cros_ec_spi.ko). Return -EPROBE_DEFER when cros_typec_probe doesn't get EC device, so the probe function can be called again after EC device is registered. Signed-off-by: Tomasz Michalec <tmichalec@google.com> Reviewed-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org> Link: https://lore.kernel.org/r/20250610153748.1858519-1-tmichalec@google.com Signed-off-by: Tzung-Bi Shih <tzungbi@kernel.org>
generated by cgit v1.3 (git 2.53.0) at 2026-11-12 15:35:02 +0000