| Age | Commit message (Collapse) | Author |
|---|
|
Marking ufence as signalled after copy_to_user() is too late.
Worker thread which signals ufence by memory write might be raced
with another userspace vm-bind call. In map/unmap scenario unmap
may still see ufence is not signalled causing -EBUSY. Change the
order of marking / write to user-fence fixes this issue.
Fixes: 977e5b82e090 ("drm/xe: Expose user fence from xe_sync_entry")
Link: https://gitlab.freedesktop.org/drm/xe/kernel/-/issues/5536
Signed-off-by: Zbigniew Kempczyński <zbigniew.kempczynski@intel.com>
Cc: Matthew Brost <matthew.brost@intel.com>
Cc: Matthew Auld <matthew.auld@intel.com>
Reviewed-by: Matthew Brost <matthew.brost@intel.com>
Signed-off-by: Matthew Brost <matthew.brost@intel.com>
Link: https://lore.kernel.org/r/20250820083903.2109891-2-zbigniew.kempczynski@intel.com
(cherry picked from commit 8ae04fe9ffc93d6bc3bc63ac08375427d69cee06)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
|
|
Add a debugfs fault handler to trigger csc error handler that
wedges the device and enables runtime survivability mode.
v2: add debugfs only for bmg (Umesh)
v3: do not use csc_fault attribute if debugfs is not enabled
v4: rebase
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Riana Tauro <riana.tauro@intel.com>
Reviewed-by: Raag Jadav <raag.jadav@intel.com>
Link: https://lore.kernel.org/r/20250826063419.3022216-11-riana.tauro@intel.com
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
|
|
Add support to handle CSC firmware reported errors. When CSC firmware
errors are encoutered, a error interrupt is received by the GFX device as
a MSI interrupt.
Device Source control registers indicates the source of the error as CSC
The HEC error status register indicates that the error is firmware reported
Depending on the type of error, the error cause is written to the HEC
Firmware error register.
On encountering such CSC firmware errors, the graphics device is
non-recoverable from driver context. The only way to recover from these
errors is firmware flash.
System admin/userspace is notified of the necessity of firmware flash
with a combination of vendor-specific drm device edged uevent, dmesg logs
and runtime survivability sysfs. It is the responsiblity of the consumer
to verify all the actions and then trigger a firmware flash using tools
like fwupd.
$ udevadm monitor --property --kernel
monitor will print the received events for:
KERNEL - the kernel uevent
KERNEL[754.709341] change /devices/pci0000:00/0000:00:01.0/0000:01:00.0/0000:02:01.0/0000:03:00.0/drm/card0 (drm)
ACTION=change
DEVPATH=/devices/pci0000:00/0000:00:01.0/0000:01:00.0/0000:02:01.0/0000:03:00.0/drm/card0
SUBSYSTEM=drm
WEDGED=vendor-specific
DEVNAME=/dev/dri/card0
DEVTYPE=drm_minor
SEQNUM=5973
MAJOR=226
MINOR=0
Logs
xe 0000:03:00.0: [drm] *ERROR* [Hardware Error]: Tile0 reported NONFATAL error 0x20000
xe 0000:03:00.0: [drm] *ERROR* [Hardware Error]: NONFATAL: HEC Uncorrected FW FD Corruption error reported, bit[2] is set
xe 0000:03:00.0: Runtime Survivability mode enabled
xe 0000:03:00.0: [drm] *ERROR* CRITICAL: Xe has declared device 0000:03:00.0 as wedged.
IOCTLs and executions are blocked. Only a rebind may clear the failure
Please file a _new_ bug report at https://gitlab.freedesktop.org/drm/xe/kernel/issues/new
xe 0000:03:00.0: [drm] device wedged, needs recovery
xe 0000:03:00.0: Firmware flash required, Please refer to the userspace documentation for more details!
Runtime survivability Sysfs:
/sys/bus/pci/devices/<device>/survivability_mode
v2: use vendor recovery method with
runtime survivability (Christian, Rodrigo, Raag)
v3: move declare wedged to runtime survivability mode (Rodrigo)
v4: update commit message
Signed-off-by: Riana Tauro <riana.tauro@intel.com>
Reviewed-by: Umesh Nerlige Ramappa <umesh.nerlige.ramappa@intel.com>
Link: https://lore.kernel.org/r/20250826063419.3022216-10-riana.tauro@intel.com
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
|
|
Gfx device reports two classes of errors: uncorrectable and
correctable. Depending on the severity uncorrectable errors are further
classified Non-Fatal and Fatal.
Correctable and Non-Fatal errors: These errors are reported as MSI. Bits in
the Master Interrupt Register indicate the class of the error.
The source of the error is then read from the Device Error Source
Register.
Fatal errors: These are reported as PCIe errors
When a PCIe error is asserted, the OS will perform a SBR (Secondary
Bus reset) which causes the driver to reload. The error registers are
sticky and the values are maintained through SBR.
Add basic support to handle these errors.
Bspec: 50875, 53073, 53074, 53075, 53076
v2: Format commit message (Umesh)
v3: fix documentation (Stuart)
Cc: Stuart Summers <stuart.summers@intel.com>
Co-developed-by: Himal Prasad Ghimiray <himal.prasad.ghimiray@intel.com>
Signed-off-by: Himal Prasad Ghimiray <himal.prasad.ghimiray@intel.com>
Signed-off-by: Riana Tauro <riana.tauro@intel.com>
Reviewed-by: Umesh Nerlige Ramappa <umesh.nerlige.ramappa@intel.com>
Link: https://lore.kernel.org/r/20250826063419.3022216-9-riana.tauro@intel.com
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
|
|
Add documentation for vendor specific device wedged recovery method
and runtime survivability.
v2: fix documentation (Raag)
v3: add userspace tool for firmware update (Raag)
v4: use consistent documentation (Raag)
v5: add more documentation
Signed-off-by: Riana Tauro <riana.tauro@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Raag Jadav <raag.jadav@intel.com>
Link: https://lore.kernel.org/r/20250826063419.3022216-8-riana.tauro@intel.com
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
|
|
Certain runtime firmware errors can cause the device to be in a unusable
state requiring a firmware flash to restore normal operation.
Runtime Survivability Mode indicates firmware flash is necessary by
wedging the device and exposing survivability mode sysfs.
The below sysfs is an indication that device is in survivability mode
/sys/bus/pci/devices/<device>/survivability_mode
v2: Fix kernel-doc (Umesh)
v3: Add user friendly dmesg (Frank)
Signed-off-by: Riana Tauro <riana.tauro@intel.com>
Reviewed-by: Raag Jadav <raag.jadav@intel.com>
Link: https://lore.kernel.org/r/20250826063419.3022216-7-riana.tauro@intel.com
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
|
|
Refactor survivability mode code to support both boot
and runtime survivability.
Signed-off-by: Riana Tauro <riana.tauro@intel.com>
Reviewed-by: Raag Jadav <raag.jadav@intel.com>
Link: https://lore.kernel.org/r/20250826063419.3022216-6-riana.tauro@intel.com
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
|
|
Add a helper function to set recovery method. The recovery
method can be set before declaring the device wedged and sending the
drm wedged uevent. If no method is set, default unbind/re-bind method
will be set.
v2: fix documentation (Raag)
Signed-off-by: Riana Tauro <riana.tauro@intel.com>
Reviewed-by: Raag Jadav <raag.jadav@intel.com>
Link: https://lore.kernel.org/r/20250826063419.3022216-5-riana.tauro@intel.com
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
|
|
Userspace should be notified after setting the device as wedged.
Re-order function calls to set gt wedged before sending uevent.
Cc: Matthew Brost <matthew.brost@intel.com>
Suggested-by: Raag Jadav <raag.jadav@intel.com>
Signed-off-by: Riana Tauro <riana.tauro@intel.com>
Reviewed-by: Matthew Brost <matthew.brost@intel.com>
Link: https://lore.kernel.org/r/20250826063419.3022216-4-riana.tauro@intel.com
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
|
|
Address the need for a recovery method (firmware flash on Firmware errors)
introduced in the later patches of Xe KMD.
Whenever XE KMD detects a firmware error, a firmware flash is required to
recover the device to normal operation.
The initial proposal to use 'firmware-flash' as a recovery method was
not applicable to other drivers and could cause multiple recovery
methods specific to vendors to be added.
To address this a more generic 'vendor-specific' method is introduced,
guiding users to refer to vendor specific documentation and system logs
for detailed vendor specific recovery procedure.
Add a recovery method 'WEDGED=vendor-specific' for such errors.
Vendors must provide additional recovery documentation if this method
is used.
It is the responsibility of the consumer to refer to the correct vendor
specific documentation and usecase before attempting a recovery.
For example: If driver is XE KMD, the consumer must refer
to the documentation of 'Device Wedging' under 'Documentation/gpu/xe/'.
v2: fix documentation (Raag)
v3: add more details to commit message (Sima, Rodrigo, Raag)
add an example script to the documentation (Raag)
v4: use consistent naming (Raag)
v5: fix commit message
v6: add more documentation
Cc: André Almeida <andrealmeid@igalia.com>
Cc: Christian König <christian.koenig@amd.com>
Cc: David Airlie <airlied@gmail.com>
Cc: Simona Vetter <simona.vetter@ffwll.ch>
Cc: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Riana Tauro <riana.tauro@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Link: https://lore.kernel.org/r/20250826063419.3022216-3-riana.tauro@intel.com
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
|
|
Add documentation for Xe Device Wedging so that
file can be referenced in following patches.
Signed-off-by: Riana Tauro <riana.tauro@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://lore.kernel.org/r/20250826063419.3022216-2-riana.tauro@intel.com
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
|
|
These iterations require the read lock, otherwise RCU
lockdep will splat:
=============================
WARNING: suspicious RCU usage
6.17.0-rc3-00014-g31419c045d64 #6 Tainted: G O
-----------------------------
drivers/base/power/main.c:1333 RCU-list traversed in non-reader section!!
other info that might help us debug this:
rcu_scheduler_active = 2, debug_locks = 1
5 locks held by rtcwake/547:
#0: 00000000643ab418 (sb_writers#6){.+.+}-{0:0}, at: file_start_write+0x2b/0x3a
#1: 0000000067a0ca88 (&of->mutex#2){+.+.}-{4:4}, at: kernfs_fop_write_iter+0x181/0x24b
#2: 00000000631eac40 (kn->active#3){.+.+}-{0:0}, at: kernfs_fop_write_iter+0x191/0x24b
#3: 00000000609a1308 (system_transition_mutex){+.+.}-{4:4}, at: pm_suspend+0xaf/0x30b
#4: 0000000060c0fdb0 (device_links_srcu){.+.+}-{0:0}, at: device_links_read_lock+0x75/0x98
stack backtrace:
CPU: 0 UID: 0 PID: 547 Comm: rtcwake Tainted: G O 6.17.0-rc3-00014-g31419c045d64 #6 VOLUNTARY
Tainted: [O]=OOT_MODULE
Stack:
223721b3a80 6089eac6 00000001 00000001
ffffff00 6089eac6 00000535 6086e528
721b3ac0 6003c294 00000000 60031fc0
Call Trace:
[<600407ed>] show_stack+0x10e/0x127
[<6003c294>] dump_stack_lvl+0x77/0xc6
[<6003c2fd>] dump_stack+0x1a/0x20
[<600bc2f8>] lockdep_rcu_suspicious+0x116/0x13e
[<603d8ea1>] dpm_async_suspend_superior+0x117/0x17e
[<603d980f>] device_suspend+0x528/0x541
[<603da24b>] dpm_suspend+0x1a2/0x267
[<603da837>] dpm_suspend_start+0x5d/0x72
[<600ca0c9>] suspend_devices_and_enter+0xab/0x736
[...]
Add the fourth argument to the iteration to annotate
this and avoid the splat.
Fixes: 06799631d522 ("PM: sleep: Make async suspend handle suppliers like parents")
Fixes: ed18738fff02 ("PM: sleep: Make async resume handle consumers like children")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Link: https://patch.msgid.link/20250826134348.aba79f6e6299.I9ecf55da46ccf33778f2c018a82e1819d815b348@changeid
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The API documenation of setup_mm_hdr does not mention that dptr can be
NULL, this is a local function, and no caller passes NULL. So drop the
unneeded check.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Acked-by: Sumit Garg <sumit.garg@oss.qualcomm.com>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
|
|
No caller ever evaluates what we return in 'ret'. They only use the
return code of the function.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Acked-by: Sumit Garg <sumit.garg@oss.qualcomm.com>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
|
|
When we are low on memory or when the internal API is violated, we
cannot return EFI_OUT_OF_RESOURCES. According to the UEFI standard, that
error code is either related to persistent storage used for the variable
or even not foreseen as possible error (GetVariable e.g.). Use the not
fully accurate but compliant error code EFI_DEVICE_ERROR in those cases.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Acked-by: Sumit Garg <sumit.garg@oss.qualcomm.com>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
|
|
The communication buffer allocated by setup_mm_hdr() is later on passed
to tee_shm_register_kernel_buf(). The latter expects those buffers to be
contiguous pages, but setup_mm_hdr() just uses kmalloc(). That can cause
various corruptions or BUGs, specifically since commit 9aec2fb0fd5e
("slab: allocate frozen pages"), though it was broken before as well.
Fix this by using alloc_pages_exact() instead of kmalloc().
Fixes: c44b6be62e8d ("efi: Add tee-based EFI variable driver")
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Acked-by: Sumit Garg <sumit.garg@oss.qualcomm.com>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
|
|
The brcmf_btcoex_detach() only shuts down the btcoex timer, if the
flag timer_on is false. However, the brcmf_btcoex_timerfunc(), which
runs as timer handler, sets timer_on to false. This creates critical
race conditions:
1.If brcmf_btcoex_detach() is called while brcmf_btcoex_timerfunc()
is executing, it may observe timer_on as false and skip the call to
timer_shutdown_sync().
2.The brcmf_btcoex_timerfunc() may then reschedule the brcmf_btcoex_info
worker after the cancel_work_sync() has been executed, resulting in
use-after-free bugs.
The use-after-free bugs occur in two distinct scenarios, depending on
the timing of when the brcmf_btcoex_info struct is freed relative to
the execution of its worker thread.
Scenario 1: Freed before the worker is scheduled
The brcmf_btcoex_info is deallocated before the worker is scheduled.
A race condition can occur when schedule_work(&bt_local->work) is
called after the target memory has been freed. The sequence of events
is detailed below:
CPU0 | CPU1
brcmf_btcoex_detach | brcmf_btcoex_timerfunc
| bt_local->timer_on = false;
if (cfg->btcoex->timer_on) |
... |
cancel_work_sync(); |
... |
kfree(cfg->btcoex); // FREE |
| schedule_work(&bt_local->work); // USE
Scenario 2: Freed after the worker is scheduled
The brcmf_btcoex_info is freed after the worker has been scheduled
but before or during its execution. In this case, statements within
the brcmf_btcoex_handler() — such as the container_of macro and
subsequent dereferences of the brcmf_btcoex_info object will cause
a use-after-free access. The following timeline illustrates this
scenario:
CPU0 | CPU1
brcmf_btcoex_detach | brcmf_btcoex_timerfunc
| bt_local->timer_on = false;
if (cfg->btcoex->timer_on) |
... |
cancel_work_sync(); |
... | schedule_work(); // Reschedule
|
kfree(cfg->btcoex); // FREE | brcmf_btcoex_handler() // Worker
/* | btci = container_of(....); // USE
The kfree() above could | ...
also occur at any point | btci-> // USE
during the worker's execution|
*/ |
To resolve the race conditions, drop the conditional check and call
timer_shutdown_sync() directly. It can deactivate the timer reliably,
regardless of its current state. Once stopped, the timer_on state is
then set to false.
Fixes: 61730d4dfffc ("brcmfmac: support critical protocol API for DHCP")
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Duoming Zhou <duoming@zju.edu.cn>
Link: https://patch.msgid.link/20250822050839.4413-1-duoming@zju.edu.cn
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Compile-testing this driver on Arm platforms shows a link failure
when the CRC functions are not part of the kernel:
x86_64-linux-ld: drivers/net/wireless/ralink/rt2x00/rt2800lib.o: in function `rt2800_check_firmware':
rt2800lib.c:(.text+0x20e5): undefined reference to `crc_ccitt'
Move the select statement to the correct Kconfig symbol to match
the call site.
Fixes: 311b05e235cf ("wifi: rt2x00: add COMPILE_TEST")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Reviewed-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Link: https://patch.msgid.link/20250731075837.1969136-1-arnd@kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The rt2800 specific code requires the more general library code:
ERROR: modpost: "rt2x00queue_get_entry" [drivers/net/wireless/ralink/rt2x00/rt2x00mmio.ko] undefined!
ERROR: modpost: "rt2x00lib_dmastart" [drivers/net/wireless/ralink/rt2x00/rt2x00mmio.ko] undefined!
ERROR: modpost: "rt2x00lib_dmadone" [drivers/net/wireless/ralink/rt2x00/rt2x00mmio.ko] undefined!
ERROR: modpost: "rt2x00lib_rxdone" [drivers/net/wireless/ralink/rt2x00/rt2x00mmio.ko] undefined!
ERROR: modpost: "rt2x00lib_txdone_nomatch" [drivers/net/wireless/ralink/rt2x00/rt2800lib.ko] undefined!
ERROR: modpost: "rt2x00lib_txdone" [drivers/net/wireless/ralink/rt2x00/rt2800lib.ko] undefined!
ERROR: modpost: "rt2x00queue_get_entry" [drivers/net/wireless/ralink/rt2x00/rt2800lib.ko] undefined!
ERROR: modpost: "rt2x00lib_get_bssidx" [drivers/net/wireless/ralink/rt2x00/rt2800lib.ko] undefined!
ERROR: modpost: "rt2x00mac_conf_tx" [drivers/net/wireless/ralink/rt2x00/rt2800lib.ko] undefined!
ERROR: modpost: "rt2x00lib_txdone_noinfo" [drivers/net/wireless/ralink/rt2x00/rt2800lib.ko] undefined!
Select the symbol to avoid this build failure.
Fixes: 7f6109086c9e ("wifi: rt2800: move 2x00soc to 2800soc")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Reviewed-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Link: https://patch.msgid.link/20250729152924.2462423-1-arnd@kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Device can be unbound, so driver must also release memory for the wakeup
source.
Link: https://lore.kernel.org/lkml/20250501-device-wakeup-leak-extcon-v2-4-7af77802cbea@linaro.org/
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
|
|
Device can be unbound, so driver must also release memory for the wakeup
source.
Link: https://lore.kernel.org/lkml/20250501-device-wakeup-leak-extcon-v2-3-7af77802cbea@linaro.org/
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
|
|
Device can be unbound, so driver must also release memory for the wakeup
source.
Link: https://lore.kernel.org/lkml/20250501-device-wakeup-leak-extcon-v2-2-7af77802cbea@linaro.org/
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
|
|
Device can be unbound, so driver must also release memory for the wakeup
source. Do not use devm interface, because it would change the order of
cleanup.
Link: https://lore.kernel.org/lkml/20250501-device-wakeup-leak-extcon-v2-1-7af77802cbea@linaro.org/
Acked-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
|
|
The Legion Go features detachable controllers which support a dual
dinput mode. In this mode, the controllers appear under a single HID
device with two applications.
Currently, both controllers appear under the same event device, causing
their controls to be mixed up. This patch separates the two so that
they can be used independently.
In addition, the latest firmware update for the Legion Go swaps the IDs
to the ones used by the Legion Go 2, so add those IDs as well.
[jkosina@suse.com: improved shortlog]
Signed-off-by: Antheas Kapenekakis <lkml@antheas.dev>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
|
|
The DT2DRBK trackball has 8 buttons, but the report descriptor only
specifies 5. This patch adds the device ID and performs a similar fixup as
for other ELECOM devices to enable the remaining 3 buttons.
Signed-off-by: Martin Hilgendorf <martin.hilgendorf@posteo.de>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
|
|
There is a redundant semicolon after a comment, remove it.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
timbgpio_irq_type() currently accepts offset == ngpio, violating
gpiolib's [0..ngpio-1] contract. This can lead to undefined behavior
when computing '1 << offset', and it is also inconsistent with users
that iterate with for_each_set_bit(..., ngpio).
Tighten the upper bound to reject offset == ngpio. No functional change
for in-range offsets.
Signed-off-by: Junjie Cao <junjie.cao@intel.com>
Link: https://lore.kernel.org/r/20250825090850.127163-1-junjie.cao@intel.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
|
|
Add the following Telit Cinterion LE910C4-WWX new compositions:
0x1034: tty (AT) + tty (AT) + rmnet
T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 8 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=1bc7 ProdID=1034 Rev=00.00
S: Manufacturer=Telit
S: Product=LE910C4-WWX
S: SerialNumber=93f617e7
C: #Ifs= 3 Cfg#= 1 Atr=e0 MxPwr=500mA
I: If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=81(I) Atr=03(Int.) MxPS= 64 Ivl=2ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I: If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=fe Prot=ff Driver=option
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=83(I) Atr=03(Int.) MxPS= 64 Ivl=2ms
E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I: If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=85(I) Atr=03(Int.) MxPS= 64 Ivl=2ms
E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
0x1036: tty (AT) + tty (AT)
T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 10 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=1bc7 ProdID=1036 Rev=00.00
S: Manufacturer=Telit
S: Product=LE910C4-WWX
S: SerialNumber=93f617e7
C: #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=500mA
I: If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=81(I) Atr=03(Int.) MxPS= 64 Ivl=2ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I: If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=fe Prot=ff Driver=option
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=83(I) Atr=03(Int.) MxPS= 64 Ivl=2ms
E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
0x1037: tty (diag) + tty (Telit custom) + tty (AT) + tty (AT) + rmnet
T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 15 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=1bc7 ProdID=1037 Rev=00.00
S: Manufacturer=Telit
S: Product=LE910C4-WWX
S: SerialNumber=93f617e7
C: #Ifs= 5 Cfg#= 1 Atr=e0 MxPwr=500mA
I: If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=30 Driver=option
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I: If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I: If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=83(I) Atr=03(Int.) MxPS= 64 Ivl=2ms
E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I: If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=fe Prot=ff Driver=option
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=85(I) Atr=03(Int.) MxPS= 64 Ivl=2ms
E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I: If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan
E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=87(I) Atr=03(Int.) MxPS= 64 Ivl=2ms
E: Ad=88(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
0x1038: tty (Telit custom) + tty (AT) + tty (AT) + rmnet
T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 9 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=1bc7 ProdID=1038 Rev=00.00
S: Manufacturer=Telit
S: Product=LE910C4-WWX
S: SerialNumber=93f617e7
C: #Ifs= 4 Cfg#= 1 Atr=e0 MxPwr=500mA
I: If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I: If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=82(I) Atr=03(Int.) MxPS= 64 Ivl=2ms
E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I: If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=fe Prot=ff Driver=option
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=84(I) Atr=03(Int.) MxPS= 64 Ivl=2ms
E: Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I: If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=86(I) Atr=03(Int.) MxPS= 64 Ivl=2ms
E: Ad=87(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
0x103b: tty (diag) + tty (Telit custom) + tty (AT) + tty (AT)
T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 10 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=1bc7 ProdID=103b Rev=00.00
S: Manufacturer=Telit
S: Product=LE910C4-WWX
S: SerialNumber=93f617e7
C: #Ifs= 4 Cfg#= 1 Atr=e0 MxPwr=500mA
I: If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=30 Driver=option
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I: If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I: If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=83(I) Atr=03(Int.) MxPS= 64 Ivl=2ms
E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I: If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=fe Prot=ff Driver=option
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=85(I) Atr=03(Int.) MxPS= 64 Ivl=2ms
E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
0x103c: tty (Telit custom) + tty (AT) + tty (AT)
T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 11 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=1bc7 ProdID=103c Rev=00.00
S: Manufacturer=Telit
S: Product=LE910C4-WWX
S: SerialNumber=93f617e7
C: #Ifs= 3 Cfg#= 1 Atr=e0 MxPwr=500mA
I: If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I: If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=82(I) Atr=03(Int.) MxPS= 64 Ivl=2ms
E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I: If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=fe Prot=ff Driver=option
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=84(I) Atr=03(Int.) MxPS= 64 Ivl=2ms
E: Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
Cc: stable@vger.kernel.org
Signed-off-by: Fabio Porcedda <fabio.porcedda@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
Add the following Telit Cinterion FN990A w/audio compositions:
0x1077: tty (diag) + adb + rmnet + audio + tty (AT/NMEA) + tty (AT) +
tty (AT) + tty (AT)
T: Bus=01 Lev=01 Prnt=01 Port=09 Cnt=01 Dev#= 8 Spd=480 MxCh= 0
D: Ver= 2.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=1bc7 ProdID=1077 Rev=05.04
S: Manufacturer=Telit Wireless Solutions
S: Product=FN990
S: SerialNumber=67e04c35
C: #Ifs=10 Cfg#= 1 Atr=e0 MxPwr=500mA
I: If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=30 Driver=option
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I: If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=(none)
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I: If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=50 Driver=qmi_wwan
E: Ad=0f(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=83(I) Atr=03(Int.) MxPS= 8 Ivl=32ms
E: Ad=8e(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I: If#= 3 Alt= 0 #EPs= 0 Cls=01(audio) Sub=01 Prot=20 Driver=snd-usb-audio
I: If#= 4 Alt= 1 #EPs= 1 Cls=01(audio) Sub=02 Prot=20 Driver=snd-usb-audio
E: Ad=03(O) Atr=0d(Isoc) MxPS= 68 Ivl=1ms
I: If#= 5 Alt= 1 #EPs= 1 Cls=01(audio) Sub=02 Prot=20 Driver=snd-usb-audio
E: Ad=84(I) Atr=0d(Isoc) MxPS= 68 Ivl=1ms
I: If#= 6 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=60 Driver=option
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=86(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
I: If#= 7 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option
E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=87(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=88(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
I: If#= 8 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option
E: Ad=06(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=89(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=8a(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
I: If#= 9 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option
E: Ad=07(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=8b(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=8c(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
0x1078: tty (diag) + adb + MBIM + audio + tty (AT/NMEA) + tty (AT) +
tty (AT) + tty (AT)
T: Bus=01 Lev=01 Prnt=01 Port=09 Cnt=01 Dev#= 21 Spd=480 MxCh= 0
D: Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=1bc7 ProdID=1078 Rev=05.04
S: Manufacturer=Telit Wireless Solutions
S: Product=FN990
S: SerialNumber=67e04c35
C: #Ifs=11 Cfg#= 1 Atr=e0 MxPwr=500mA
I: If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=30 Driver=option
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I: If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=(none)
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I: If#=10 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option
E: Ad=07(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=8b(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=8c(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
I: If#= 2 Alt= 0 #EPs= 1 Cls=02(commc) Sub=0e Prot=00 Driver=cdc_mbim
E: Ad=83(I) Atr=03(Int.) MxPS= 64 Ivl=32ms
I: If#= 3 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim
E: Ad=0f(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=8e(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I: If#= 4 Alt= 0 #EPs= 0 Cls=01(audio) Sub=01 Prot=20 Driver=snd-usb-audio
I: If#= 5 Alt= 0 #EPs= 0 Cls=01(audio) Sub=02 Prot=20 Driver=snd-usb-audio
I: If#= 6 Alt= 1 #EPs= 1 Cls=01(audio) Sub=02 Prot=20 Driver=snd-usb-audio
E: Ad=84(I) Atr=0d(Isoc) MxPS= 68 Ivl=1ms
I: If#= 7 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=60 Driver=option
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=86(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
I: If#= 8 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option
E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=87(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=88(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
I: If#= 9 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option
E: Ad=06(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=89(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=8a(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
0x1079: RNDIS + tty (diag) + adb + audio + tty (AT/NMEA) + tty (AT) +
tty (AT) + tty (AT)
T: Bus=01 Lev=01 Prnt=01 Port=09 Cnt=01 Dev#= 23 Spd=480 MxCh= 0
D: Ver= 2.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=1bc7 ProdID=1079 Rev=05.04
S: Manufacturer=Telit Wireless Solutions
S: Product=FN990
S: SerialNumber=67e04c35
C: #Ifs=11 Cfg#= 1 Atr=e0 MxPwr=500mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=ef(misc ) Sub=04 Prot=01 Driver=rndis_host
E: Ad=81(I) Atr=03(Int.) MxPS= 8 Ivl=32ms
I: If#= 1 Alt= 0 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=rndis_host
E: Ad=0f(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=8e(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I: If#=10 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option
E: Ad=07(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=8b(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=8c(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
I: If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=30 Driver=option
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I: If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=(none)
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I: If#= 4 Alt= 0 #EPs= 0 Cls=01(audio) Sub=01 Prot=20 Driver=snd-usb-audio
I: If#= 5 Alt= 0 #EPs= 0 Cls=01(audio) Sub=02 Prot=20 Driver=snd-usb-audio
I: If#= 6 Alt= 1 #EPs= 1 Cls=01(audio) Sub=02 Prot=20 Driver=snd-usb-audio
E: Ad=84(I) Atr=0d(Isoc) MxPS= 68 Ivl=1ms
I: If#= 7 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=60 Driver=option
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=86(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
I: If#= 8 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option
E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=87(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=88(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
I: If#= 9 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option
E: Ad=06(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=89(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=8a(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
Cc: stable@vger.kernel.org
Signed-off-by: Fabio Porcedda <fabio.porcedda@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
This reverts commit 482c7e296edc0f594e8869a789a40be53c49bd6a.
The dma_buf field in struct drm_gem_object is not stable over the
object instance's lifetime. The field becomes NULL when user space
releases the final GEM handle on the buffer object. This resulted
in a NULL-pointer deref.
Workarounds in commit 5307dce878d4 ("drm/gem: Acquire references on
GEM handles for framebuffers") and commit f6bfc9afc751 ("drm/framebuffer:
Acquire internal references on GEM handles") only solved the problem
partially. They especially don't work for buffer objects without a DRM
framebuffer associated.
Hence, this revert to going back to using .import_attach->dmabuf.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Simona Vetter <simona.vetter@ffwll.ch>
Link: https://lore.kernel.org/r/20250715084549.41473-1-tzimmermann@suse.de
|
|
Add support for DRM_FORMAT_C8 to vesadrm. The new pixel-format
description PIXEL_FORMAT_C8 describes the layout. Vesadrm's helpers
vesadrm_fill_palette_lut() and vesadrm_load_palette_lut() set the
hardware palette according to the CRTC's output format.
The driver emulates XRGB8888 by converting the source buffer to
RGB332 and using the resulting 256 colors as index into the hardware
palette. The hardware palette converts back to RGB during scanout.
This has no overhead compared to other format conversion, but allows
common userspace, such as Wayland compositors, to operate on the
display.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://lore.kernel.org/r/20250714151513.309475-10-tzimmermann@suse.de
|
|
Distiguish between component-based formats and 'the rest' in vesadrm's
color management. Scanout buffers with component-based format allow
for gamma correction. Palette-based formats (i.e., 'the rest') require
palette setup.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://lore.kernel.org/r/20250714151513.309475-9-tzimmermann@suse.de
|
|
Rename vesadrm's gamma helpers in preparation of the upcoming support
for color palettes. Gamma correction and color palettes share the same
hardware features, but the driver's old naming only indicated support
for gamma LUTs.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://lore.kernel.org/r/20250714151513.309475-8-tzimmermann@suse.de
|
|
List the conversion from XRGB8888-to-RGB332 in drm_fb_blit(), so that
drivers based on sysfb-helpers can use it.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://lore.kernel.org/r/20250714151513.309475-7-tzimmermann@suse.de
|
|
Add helper drm_crtc_fill_palette_332(), which fills palettes with
RGB332 color data. Each color in RGB332 format serves as an index
into an 8-bit palette that stores the corresponding component-based
colors.
Vesadrm will use the new helper to emulate RGB formats on top of
framebuffers in C8 format.
v2:
- add comments on bit operations (Javier)
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://lore.kernel.org/r/20250714151513.309475-6-tzimmermann@suse.de
|
|
Use the color format stored in struct drm_sysfb_crtc_state for
color-format conversion instead of the scanout-buffer format
announced by firmware. Currently, both values are identical.
This will allow drivers to modify the CRTC's input format to a
certain extend. Specifically, vesadrm will be able to display RGB
framebuffers when the scanout buffer is of C8 format. With color-
format conversion to RGB332 and correct setup of the C8 palette,
displaying XRGB8888-based buffers under C8 can be achieved.
v2:
- refer to RGB332 as CRTC input format
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://lore.kernel.org/r/20250714151513.309475-5-tzimmermann@suse.de
|
|
Convert drm_sysfb_get_format_si() to lookup the screen_info color
format as struct pixel_format with screen_info_pixel_format(). Then
search the list of given formats for the screen_info format with
pixel_format_equal().
Replaces custom code with helpers. The pixel-compare helper
pixel_format_equal() also handles indexed color formats. Prepares
for sysfb drivers to support color palettes.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://lore.kernel.org/r/20250714151513.309475-4-tzimmermann@suse.de
|
|
Add screen_info_pixel_format(), which converts a screen_info's
information about the color format to struct pixel_format. The encoding
within the screen_info structure is complex and therefore prone to
errors. Later patches will convert callers to use the pixel format.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://lore.kernel.org/r/20250714151513.309475-3-tzimmermann@suse.de
|
|
POWER8 support a maximum of 16 subcrq indirect descriptor entries per
H_SEND_SUB_CRQ_INDIRECT call, while POWER9 and newer hypervisors
support up to 128 entries. Increasing the max number of indirect
descriptor entries improves batching efficiency and reduces
hcall overhead, which enhances throughput under large workload on POWER9+.
Currently, ibmvnic driver always uses a fixed number of max indirect
descriptor entries (16). send_subcrq_indirect() treats all hypervisor
errors the same:
- Cleanup and Drop the entire batch of descriptors.
- Return an error to the caller.
- Rely on TCP/IP retransmissions to recover.
- If the hypervisor returns H_PARAMETER (e.g., because 128
entries are not supported on POWER8), the driver will continue
to drop batches, resulting in unnecessary packet loss.
In this patch:
Raise the default maximum indirect entries to 128 to improve ibmvnic
batching on morden platform. But also gracefully fall back to
16 entries for Power 8 systems.
Since there is no VIO interface to query the hypervisor’s supported
limit, vnic handles send_subcrq_indirect() H_PARAMETER errors:
- On first H_PARAMETER failure, log the failure context
- Reduce max_indirect_entries to 16 and allow the single batch to drop.
- Subsequent calls automatically use the correct lower limit,
avoiding repeated drops.
The goal is to optimizes performance on modern systems while handles
falling back for older POWER8 hypervisors.
Performance shows 40% improvements with MTU (1500) on largework load.
Signed-off-by: Mingming Cao <mmc@linux.ibm.com>
Reviewed-by: Brian King <bjking1@linux.ibm.com>
Reviewed-by: Haren Myneni <haren@linux.ibm.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250821130215.97960-1-mmc@linux.ibm.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
"Use after free" issue appears in suspend once race occurs when
napi poll scheduls after `netif_device_detach` and before napi disables.
For details, during suspend flow of virtio-net,
the tx queue state is set to "__QUEUE_STATE_DRV_XOFF" by CPU-A.
And at some coincidental times, if a TCP connection is still working,
CPU-B does `virtnet_poll` before napi disable.
In this flow, the state "__QUEUE_STATE_DRV_XOFF"
of tx queue will be cleared. This is not the normal process it expects.
After that, CPU-A continues to close driver then virtqueue is removed.
Sequence likes below:
--------------------------------------------------------------------------
CPU-A CPU-B
----- -----
suspend is called A TCP based on
virtio-net still work
virtnet_freeze
|- virtnet_freeze_down
| |- netif_device_detach
| | |- netif_tx_stop_all_queues
| | |- netif_tx_stop_queue
| | |- set_bit
| | (__QUEUE_STATE_DRV_XOFF,...)
| | softirq rasied
| | |- net_rx_action
| | |- napi_poll
| | |- virtnet_poll
| | |- virtnet_poll_cleantx
| | |- netif_tx_wake_queue
| | |- test_and_clear_bit
| | (__QUEUE_STATE_DRV_XOFF,...)
| |- virtnet_close
| |- virtnet_disable_queue_pair
| |- virtnet_napi_tx_disable
|- remove_vq_common
--------------------------------------------------------------------------
When TCP delayack timer is up, a cpu gets softirq and irq handler
`tcp_delack_timer_handler` will be called, which will finally call
`start_xmit` in virtio net driver.
Then the access to tx virtq will cause panic.
The root cause of this issue is that napi tx
is not disable before `netif_tx_stop_queue`,
once `virnet_poll` schedules in such coincidental time,
the tx queue state will be cleared.
To solve this issue, adjusts the order of
function `virtnet_close` in `virtnet_freeze_down`.
Co-developed-by: Ying Xu <ying123.xu@samsung.com>
Signed-off-by: Ying Xu <ying123.xu@samsung.com>
Signed-off-by: Junnan Wu <junnan01.wu@samsung.com>
Message-Id: <20250812090817.3463403-1-junnan01.wu@samsung.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
When executing suspend to ram, if lacking the operations
to reset device and free unused buffers before deleting
a vq, resource leaks and inconsistent device status will
appear.
According to chapter "3.3.1 Driver Requirements: Device Cleanup:"
of virtio-specification:
Driver MUST ensure a virtqueue isn’t live
(by device reset) before removing exposed
buffers.
Therefore, modify the virtinput_freeze function to reset the
device and delete the unused buffers before deleting the
virtqueue, just like virtinput_remove does.
Co-developed-by: Ying Xu <ying123.xu@samsung.com>
Signed-off-by: Ying Xu <ying123.xu@samsung.com>
Co-developed-by: Junnan Wu <junnan01.wu@samsung.com>
Signed-off-by: Junnan Wu <junnan01.wu@samsung.com>
Signed-off-by: Ying Gao <ying01.gao@samsung.com>
Message-Id: <20250812095118.3622717-1-ying01.gao@samsung.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
When operating on struct vhost_net_ubuf_ref, the following execution
sequence is theoretically possible:
CPU0 is finalizing DMA operation CPU1 is doing VHOST_NET_SET_BACKEND
// ubufs->refcount == 2
vhost_net_ubuf_put() vhost_net_ubuf_put_wait_and_free(oldubufs)
vhost_net_ubuf_put_and_wait()
vhost_net_ubuf_put()
int r = atomic_sub_return(1, &ubufs->refcount);
// r = 1
int r = atomic_sub_return(1, &ubufs->refcount);
// r = 0
wait_event(ubufs->wait, !atomic_read(&ubufs->refcount));
// no wait occurs here because condition is already true
kfree(ubufs);
if (unlikely(!r))
wake_up(&ubufs->wait); // use-after-free
This leads to use-after-free on ubufs access. This happens because CPU1
skips waiting for wake_up() when refcount is already zero.
To prevent that use a read-side RCU critical section in vhost_net_ubuf_put(),
as suggested by Hillf Danton. For this lock to take effect, free ubufs with
kfree_rcu().
Cc: stable@vger.kernel.org
Fixes: 0ad8b480d6ee9 ("vhost: fix ref cnt checking deadlock")
Reported-by: Andrey Ryabinin <arbn@yandex-team.com>
Suggested-by: Hillf Danton <hdanton@sina.com>
Signed-off-by: Nikolay Kuratov <kniv@yandex-team.ru>
Message-Id: <20250805130917.727332-1-kniv@yandex-team.ru>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
This patch fixes misleading comments in both legacy and modern
virtio-pci device implementations. The comments previously referred to
the "config vector" for parameters and return values of the
`vp_legacy_queue_vector()` and `vp_modern_queue_vector()` functions,
which is incorrect.
Signed-off-by: Liming Wu <liming.wu@jaguarmicro.com>
Message-Id: <20250731092757.1000-1-liming.wu@jaguarmicro.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
Commit 1845ada47f6d ("octeontx2-af: cn10k: Add RPM LMAC pause frame
support") remove cgx_lmac_[s|g]et_pause_frm() and leave these unused.
Signed-off-by: Yue Haibing <yuehaibing@huawei.com>
Link: https://patch.msgid.link/20250820123007.1705047-1-yuehaibing@huawei.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
We are currently removing underrun on idle PSR WA even if it's not
applied. Fix this by checking pkg_c_latency_used on PSR exit as well.
Fixes: 9b1795e9b0ae ("drm/i915/psr: Underrun on idle PSR wa only when pkgc latency > delayed vblank")
Signed-off-by: Jouni Högander <jouni.hogander@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Link: https://lore.kernel.org/r/20250822105846.1023631-1-jouni.hogander@intel.com
|
|
Use string_choices.h helpers instead of hard-coded strings.
Signed-off-by: Chelsy Ratnawat <chelsyratnawat2001@gmail.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
Introduce the DRM_IOCTL_XE_VM_QUERY_MEMORY_RANGE_ATTRS ioctl to allow
userspace to query memory attributes of VMAs within a user specified
virtual address range.
Userspace first calls the ioctl with num_mem_ranges = 0,
sizeof_mem_ranges_attr = 0 and vector_of_vma_mem_attr = NULL to retrieve
the number of memory ranges (vmas) and size of each memory range attribute.
Then, it allocates a buffer of that size and calls the ioctl again to fill
the buffer with memory range attributes.
This two-step interface allows userspace to first query the required
buffer size, then retrieve detailed attributes efficiently.
v2 (Matthew Brost)
- Use same ioctl to overload functionality
v3
- Add kernel-doc
v4
- Make uapi future proof by passing struct size (Matthew Brost)
- make lock interruptible (Matthew Brost)
- set reserved bits to zero (Matthew Brost)
- s/__copy_to_user/copy_to_user (Matthew Brost)
- Avod using VMA term in uapi (Thomas)
- xe_vm_put(vm) is missing (Shuicheng)
v5
- Nits
- Fix kernel-doc
Cc: Matthew Brost <matthew.brost@intel.com>
Cc: Shuicheng Lin <shuicheng.lin@intel.com>
Cc: Thomas Hellström <thomas.hellstrom@linux.intel.com>
Reviewed-by: Matthew Brost <matthew.brost@intel.com>
Link: https://lore.kernel.org/r/20250821173104.3030148-21-himal.prasad.ghimiray@intel.com
Signed-off-by: Himal Prasad Ghimiray <himal.prasad.ghimiray@intel.com>
|
|
Ioctl enables setting up of memory attributes in user provided range.
Reviewed-by: Matthew Brost <matthew.brost@intel.com>
Link: https://lore.kernel.org/r/20250821173104.3030148-20-himal.prasad.ghimiray@intel.com
Signed-off-by: Himal Prasad Ghimiray <himal.prasad.ghimiray@intel.com>
|
|
Restore default memory attributes for VMAs during garbage collection
if they were modified by madvise. Reuse existing VMA if fully overlapping;
otherwise, allocate a new mirror VMA.
v2 (Matthew Brost)
- Add helper for vma split
- Add retry to get updated vma
v3
- Rebase on gpuvm layer
Suggested-by: Matthew Brost <matthew.brost@intel.com>
Reviewed-by: Matthew Brost <matthew.brost@intel.com>
Link: https://lore.kernel.org/r/20250821173104.3030148-19-himal.prasad.ghimiray@intel.com
Signed-off-by: Himal Prasad Ghimiray <himal.prasad.ghimiray@intel.com>
|
|
Introduce a new helper function `xe_vma_has_default_mem_attrs()` to
determine whether a VMA's memory attributes are set to their default
values. This includes checks for atomic access, PAT index, and preferred
location.
Also, add a new field `default_pat_index` to `struct xe_vma_mem_attr`
to track the initial PAT index set during the first bind. This helps
distinguish between default and user-modified pat index, such as those
changed via madvise.
Reviewed-by: Matthew Brost <matthew.brost@intel.com>
Link: https://lore.kernel.org/r/20250821173104.3030148-18-himal.prasad.ghimiray@intel.com
Signed-off-by: Himal Prasad Ghimiray <himal.prasad.ghimiray@intel.com>
|
