| Age | Commit message (Collapse) | Author |
|---|
|
Jan Höppner says:
====================
The tape device driver is limited to a block size of 65535 bytes since a
single CCW can only transfer up to 64K-1 bytes (The count field is a
16bit value). This series introduces data chaining for all read/write
functions to support block sizes larger than 65535.
The tape device type 3490 (emulated) and 3590/3592 can handle up to
256K. [1]
[1] https://www.ibm.com/docs/en/zos/3.1.0?topic=blksize-system-determined-block-size
====================
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
The tape device type 3590/3592 and emulated 3490 VTS can handle a block
size of up to 256K bytes. Currently the tape device driver is limited to
a block size of 65535 bytes (64K-1). This limitation stems from the
maximum of 65535 bytes of data that can be transferred with one
Channel-Command Word (CCW).
To work around this limitation data chaining is used which uses several
CCW to transfer an entire 256K block of data. A single CCW holds a
maximum of 65535 bytes of data.
Set MAX_BLOCKSIZE to 262144 (= 256K) to allow for data transfers with
larger block sizes. The read_block() and write_block() discipline
functions calculate the number of CCWs required based on the IDAL buffer
array size that was created for a given block size. If there is more
than one CCW required for the data transfer, the new helper function
tape_ccw_dc_idal() is used to build the data chain accordingly.
The Interruption-Repsonse Block (irb) is added to the tape_request
struct so that the tapechar_read/write() functions can analyze what data
was read or written accordingly.
Signed-off-by: Jan Höppner <hoeppner@linux.ibm.com>
Reviewed-by: Jens Remus <jremus@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
The tape device driver uses a single idal_buffer for I/O. While the
buffer itself can be arbitrary big, the limit for data transfer for a
single Channel-Command Word is at 65535 bytes (64K-1) since the count
field specifying the amount of data designated by the CCW is a 16-bit
unsigned value.
Provide functionality that allocates an array of multiple IDAL buffer
with the limitation mentioned above in mind.
A call to idal_buffer_array_alloc() allocates an array with a certain
amount of IDAL buffers which is determined based on the total size of
@size. Each individual buffer is limited to a size of CCW_MAX_BYTE_COUNT
(65535 bytes).
Add helper functions that determine the size (# of elements) and the
total data size covered by the array as well.
Current users of the single IDAL buffer are adapted to use the new
functions with one buffer to allocate.
The single IDAL buffer is removed from the tape_char_data struct.
Signed-off-by: Jan Höppner <hoeppner@linux.ibm.com>
Reviewed-by: Jens Remus <jremus@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
Currently tapechar_check_idalbuffer() is part of tape_char.c and is used
to ensure the idal buffer is big enough for the requested I/O and
reallocates a new one if required. The same is done in tape_std.c when a
fixed block size is set using the mtsetblk command. This is essentially
duplicate code.
The allocation of the buffer that is required for I/O can be considered
core functionality. Move the idal buffer allocation to tape_core.c,
make it generally available, and reduce code duplication.
Signed-off-by: Jan Höppner <hoeppner@linux.ibm.com>
Reviewed-by: Jens Remus <jremus@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
In contrast to all other helper functions used to build CCW chains,
tape_ccw_cc_idal() and tape_ccw_end_idal() return values using
post-increments, which results in returning the same CCW pointer.
Though, the intent of the CCW helper functions is to return the _next_
CCW in the chain, which can then be processed.
There is currently no actual issue, as tape_ccw_cc_idal() is not used
yet and tape_ccw_end_idal() is only used at the end of a chain.
Change both functions return statement to ccw + 1 and bring them in line
with the other helper functions.
Signed-off-by: Jan Höppner <hoeppner@linux.ibm.com>
Reviewed-by: Jens Remus <jremus@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
The Read Opposite error recovery code required 2 extra CCWs to be
allocated in order to transform the request. As this error recovery code
for both 34xx and 3590 was removed the additional allocation isn't
required anymore. Reduce it to two.
Signed-off-by: Jan Höppner <hoeppner@linux.ibm.com>
Reviewed-by: Jens Remus <jremus@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
On old native type 3590 tape devices a Read Opposite error recovery
procedure on Error Recovery Action Code (ERA) 26 was issued if a Read
Forward command failed. This recovery procedure was implemented with the
Read Backward command. This is no longer supported.
Remove 3590 ERA 26 and Read Backward related recovery code.
Signed-off-by: Jan Höppner <hoeppner@linux.ibm.com>
Reviewed-by: Jens Remus <jremus@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
On old native type 3490 tape devices a Read Opposite error recovery
procedure on Error Recovery Action Code (ERA) 26 was issued if a Read
Forward command failed. This recovery procedure was implemented with the
Read Backward command.
As a preparation for a subsequent commit, that adds support for bigger
block sizes, remove the 34xx ERA 26 related recovery code. The recovery
code would need to be adapted to the bigger block sizes, without any
possibility to be tested, as modern Virtual Tape Servers (VTS) do
neither report ERA 26 on a Read Forward command failure nor support the
error recovery procedure anymore.
Signed-off-by: Jan Höppner <hoeppner@linux.ibm.com>
Reviewed-by: Jens Remus <jremus@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
The count parameter of the read/write_block discipline functions was
never used. Remove it.
Signed-off-by: Jan Höppner <hoeppner@linux.ibm.com>
Reviewed-by: Jens Remus <jremus@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
Sumanth Korikkar says:
====================
Provide a new interface for dynamic configuration and
deconfiguration of hotplug memory on s390, allowing with/without
memmap_on_memory support. It is a follow up on the discussion with David
when introducing memmap_on_memory support for s390 and support dynamic
(de)configuration of memory:
https://lore.kernel.org/all/ee492da8-74b4-4a97-8b24-73e07257f01d@redhat.com/
https://lore.kernel.org/all/20241202082732.3959803-1-sumanthk@linux.ibm.com/
The original motivation for introducing memmap_on_memory on s390 was to
avoid using online memory to store struct pages metadata, particularly
for standby memory blocks. This became critical in cases where there was
an imbalance between standby and online memory, potentially leading to
boot failures due to insufficient memory for metadata allocation.
To address this, memmap_on_memory was utilized on s390. However, in its
current form, it adds struct pages metadata at the start of each memory
block at the time of addition (only standby memory), and this
configuration is static. It cannot be changed at runtime (When the user
needs continuous physical memory).
Inorder to provide more flexibility to the user and overcome the above
limitation, add an option to dynamically configure and deconfigure
hotpluggable memory block with/without memmap_on_memory.
With the new interface, s390 will not add all possible hotplug memory in
advance, like before, to make it visible in sysfs for online/offline
actions. Instead, before memory block can be set online, it has to be
configured via a new interface in /sys/firmware/memory/memoryX/config,
which makes s390 similar to others. i.e. Adding of hotpluggable memory is
controlled by the user instead of adding it at boottime.
s390 kernel sysfs interface to configure/deconfigure memory with
memmap_on_memory (with upcoming lsmem changes):
* Initial memory layout:
lsmem -o RANGE,SIZE,STATE,BLOCK,CONFIGURED,MEMMAP_ON_MEMORY
RANGE SIZE STATE BLOCK CONFIGURED MEMMAP_ON_MEMORY
0x00000000-0x7fffffff 2G online 0-15 yes no
0x80000000-0xffffffff 2G offline 16-31 no yes
* Configure memory
echo 1 > /sys/firmware/memory/memory16/config
lsmem -o RANGE,SIZE,STATE,BLOCK,CONFIGURED,MEMMAP_ON_MEMORY
RANGE SIZE STATE BLOCK CONFIGURED MEMMAP_ON_MEMORY
0x00000000-0x7fffffff 2G online 0-15 yes no
0x80000000-0x87ffffff 128M offline 16 yes yes
0x88000000-0xffffffff 1.9G offline 17-31 no yes
* Deconfigure memory
echo 0 > /sys/firmware/memory/memory16/config
lsmem -o RANGE,SIZE,STATE,BLOCK,CONFIGURED,MEMMAP_ON_MEMORY
RANGE SIZE STATE BLOCK CONFIGURED MEMMAP_ON_MEMORY
0x00000000-0x7fffffff 2G online 0-15 yes no
0x80000000-0xffffffff 2G offline 16-31 no yes
* Enable memmap_on_memory and online it.
(Deconfigure first)
echo 0 > /sys/devices/system/memory/memory5/online
echo 0 > /sys/firmware/memory/memory5/config
lsmem -o RANGE,SIZE,STATE,BLOCK,CONFIGURED,MEMMAP_ON_MEMORY
RANGE SIZE STATE BLOCK CONFIGURED MEMMAP_ON_MEMORY
0x00000000-0x27ffffff 640M online 0-4 yes no
0x28000000-0x2fffffff 128M offline 5 no no
0x30000000-0x7fffffff 1.3G online 6-15 yes no
0x80000000-0xffffffff 2G offline 16-31 no yes
(Enable memmap_on_memory and online it)
echo 1 > /sys/firmware/memory/memory5/memmap_on_memory
echo 1 > /sys/firmware/memory/memory5/config
echo 1 > /sys/devices/system/memory/memory5/online
lsmem -o RANGE,SIZE,STATE,BLOCK,CONFIGURED,MEMMAP_ON_MEMORY
RANGE SIZE STATE BLOCK CONFIGURED MEMMAP_ON_MEMORY
0x00000000-0x27ffffff 640M online 0-4 yes no
0x28000000-0x2fffffff 128M online 5 yes yes
0x30000000-0x7fffffff 1.3G online 6-15 yes no
0x80000000-0xffffffff 2G offline 16-31 no yes
* Disable memmap_on_memory and online it.
(Deconfigure first)
echo 0 > /sys/devices/system/memory/memory5/online
echo 0 > /sys/firmware/memory/memory5/config
lsmem -o RANGE,SIZE,STATE,BLOCK,CONFIGURED,MEMMAP_ON_MEMORY
RANGE SIZE STATE BLOCK CONFIGURED MEMMAP_ON_MEMORY
0x00000000-0x27ffffff 640M online 0-4 yes no
0x28000000-0x2fffffff 128M offline 5 no yes
0x30000000-0x7fffffff 1.3G online 6-15 yes no
0x80000000-0xffffffff 2G offline 16-31 no yes
(Disable memmap_on_memory and online it)
echo 0 > /sys/firmware/memory/memory5/memmap_on_memory
echo 1 > /sys/firmware/memory/memory5/config
echo 1 > /sys/devices/system/memory/memory5/online
lsmem -o RANGE,SIZE,STATE,BLOCK,CONFIGURED,MEMMAP_ON_MEMORY
RANGE SIZE STATE BLOCK CONFIGURED MEMMAP_ON_MEMORY
0x00000000-0x7fffffff 2G online 0-15 yes no
0x80000000-0xffffffff 2G offline 16-31 no yes
* Userspace changes:
lsmem/chmem tool is also changed to use the new interface. I will send
it to util-linux soon.
Patch 1 adds support for removal of boot-allocated memory blocks.
Patch 2 provides option to dynamically configure and deconfigure memory
with/without memmap_on_memory.
Patch 3 removes MHP_OFFLINE_INACCESSIBLE from s390. The mhp flag was
used to mark memory as not accessible until memory hotplug online phase
begins. However, with patch 2, it is no longer essential. Memory can be
brought to accessible state before adding memory, as the memory is added
during runttime now instead of boottime.
Patch 4 removes the MEM_PREPARE_ONLINE/MEM_FINISH_OFFLINE notifiers. It
is no longer needed. Memory can be brought to accessible state before
adding memory now, with runtime (de)configuration of memory.
Note: The patches apply to the linux-next branch.
v3:
Thanks David
* Avoid goto label in create_standby_sclp_mems().
* Use unsigned long instead of u64.
* Add Acked-by.
v2:
Thanks David
* Rename struct mblock/mblock_arg with struct sclp_mem/sclp_mem_arg.
* Rename all mblocks/mblock references with sclp_mems/sclp_mem -
structures, functions.
* Rename create_online_mblock() with create_configured_sclp_mem().
* Rename config_mblock_show()/config_mblock_store() with
config_sclp_mem_show()/config_sclp_mem_store().
* Remove contains_standby_increment() and
sclp_mem_notifier. sclp mem state change is performed when
adding/removing memory. sclp memory notifier - no longer needed with
this patchset.
* Recover sclp mem state when add_memory() fails.
* Refactor and add function init_sclp_mem().
* Use unsigned long instead of unsigned long long.
* Simplify and correct kobj handling. Thanks Heiko.
====================
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
Use scnprintf() instead of sprintf() for those cases where the destination
is an array and the size of the array is known at compile time.
This prevents theoretical buffer overflows, but also avoids that people
again and again spend time to figure out if the code is actually safe.
Reviewed-by: Jan Polensky <japo@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
Use scnprintf() instead of sprintf() for those cases where the destination
is an array and the size of the array is known at compile time.
This prevents theoretical buffer overflows, but also avoids that people
again and again spend time to figure out if the code is actually safe.
Reviewed-by: Jan Höppner <hoeppner@linux.ibm.com>
Reviewed-by: Jan Polensky <japo@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
Use scnprintf() instead of sprintf() for those cases where the destination
is an array and the size of the array is known at compile time.
This prevents theoretical buffer overflows, but also avoids that people
again and again spend time to figure out if the code is actually safe.
Reviewed-by: Jan Polensky <japo@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
Use scnprintf() instead of sprintf() for those cases where the destination
is an array and the size of the array is known at compile time.
This prevents theoretical buffer overflows, but also avoids that people
again and again spend time to figure out if the code is actually safe.
Reviewed-by: Jan Polensky <japo@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
https://gitlab.freedesktop.org/drm/misc/kernel into drm-next
drm-misc-next for v6.19:
UAPI Changes:
Cross-subsystem Changes:
- fbcon cleanups.
- Make drivers depend on FB_TILEBLITTING instead of selecting it,
and hide FB_MODE_HELPERS.
Core Changes:
- More preparations for rust.
- Throttle dirty worker with vblank
- Use drm_for_each_bridge_in_chain_scoped in drm's bridge code and
assorted fixes.
- Ensure drm_client_modeset tests are enabled in UML.
- Rename ttm_bo_put to ttm_bo_fini, as a further step in removing the
TTM bo refcount.
- Add POST_LT_ADJ_REQ training sequence.
- Show list of removed but still allocated bridges.
- Add a simulated vblank interrupt for hardware without it,
and add some helpers to use them in vkms and hypervdrm.
Driver Changes:
- Assorted small fixes, cleanups and updates to host1x, tegra,
panthor, amdxdna, gud, vc4, ssd130x, ivpu, panfrost, panthor,
sysfb, bridge/sn65dsi86, solomon, ast, tidss.
- Convert drivers from using .round_rate() to .determine_rate()
- Add support for KD116N3730A07/A12, chromebook mt8189, JT101TM023,
LQ079L1SX01, raspberrypi 5" panels.
- Improve reclocking on tegra186+ with nouveau.
- Improve runtime pm in amdxdna.
- Add support for HTX_PAI in imx.
- Use a helper to calculate dumb buffer sizes in most drivers.
Signed-off-by: Simona Vetter <simona.vetter@ffwll.ch>
From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://lore.kernel.org/r/b412fb91-8545-466a-8102-d89c0f2758a7@linux.intel.com
|
|
RTL8192CU disappears and reappears when rtl8xxxu is unloaded:
usbcore: deregistering interface driver rtl8xxxu
wlp3s0f3u2: deauthenticating from ... by local choice (Reason: 3=DEAUTH_LEAVING)
usb 1-2: rtl8xxxu_active_to_emu: Disabling MAC timed out
usb 1-2: USB disconnect, device number 7
usb 1-2: disconnecting
usb 1-2: new high-speed USB device number 8 using xhci_hcd
usb 1-2: New USB device found, idVendor=0bda, idProduct=8178, bcdDevice= 2.00
usb 1-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 1-2: Product: 802.11n WLAN Adapter
usb 1-2: Manufacturer: Realtek
usb 1-2: SerialNumber: 00e04c000001
This is because rtl8xxxu is using the power off sequence for RTL8723AU.
Add the correct power off sequence for RTL8192CU.
rtl8xxxu_power_off(), rtl8xxxu_active_to_emu(), and
rtl8xxxu_emu_to_disabled() are now only used for RTL8723AU, so move
them to 8723a.c and rename them to have the "rtl8723au" prefix.
Tested only with RTL8192CU.
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Reviewed-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/b9d3f137-12ce-4bd9-8ada-3b8874bc3615@gmail.com
|
|
Someone reported a problem with their TP-Link WN722N (RTL8188EUS):
usb 1-1: This Realtek USB WiFi dongle (0x2357:0x010c) is untested!
usb 1-1: Please report results to Jes.Sorensen@gmail.com
usb 1-1: Fatal - failed to parse EFuse
rtl8xxxu: probe of 1-1:1.0 failed with error -22
This error can happen when the first two bytes of the efuse don't have
the expected magic value of 0x8129. In a situation like this it could
be useful to see the contents of the efuse.
Dump the efuse right after reading it, before trying to parse it.
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Reviewed-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/1f544dc4-17f6-4401-995d-5cb4567b82fa@gmail.com
|
|
These chips don't report the signal strength for many (any?) data
frames. When the signal strength is not known, set RX_FLAG_NO_SIGNAL_VAL
in order to avoid reporting a signal strength of 0.
Tested with RTL8192FU and RTL8192CU.
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Reviewed-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/cdbe1a18-f6f1-4575-bad9-e85db8101247@gmail.com
|
|
Replace hardcoded strings with 'str_on_off()', 'str_enable_disable()',
and 'str_read_write()'.
The change improves readability.
Signed-off-by: Yu-Chun Lin <eleanor15x@gmail.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20250930000545.2192692-1-eleanor15x@gmail.com
|
|
Add USB ID 2001:3329 for D-Link AC13U rev. A1 which is a RTL8812CU-based
Wi-Fi adapter.
Compile tested only.
Cc: stable@vger.kernel.org # 6.6.x
Signed-off-by: Zenm Chen <zenmchen@gmail.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20250929035719.6172-2-zenmchen@gmail.com
|
|
Add USB ID 2001:3328 for D-Link AN3U rev. A1 which is a RTL8192FU-based
Wi-Fi adapter.
Compile tested only.
Cc: stable@vger.kernel.org # 6.6.x
Signed-off-by: Zenm Chen <zenmchen@gmail.com>
Reviewed-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20250929035719.6172-1-zenmchen@gmail.com
|
|
Add support for the second PCIe Root Complex present on Airoha AN7583
SoC.
This is based on the Mediatek Gen1/2 PCIe driver and similar to Gen3
also require workaround for the reset signals.
Introduce a new quirk to skip having to reset signals and also introduce
some additional logic to configure the PBUS registers required for Airoha
SoC.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://patch.msgid.link/20251020111121.31779-6-ansuelsmth@gmail.com
|
|
Use the generic PCI MACRO for TPVPERL delay to wait for clock and power
stabilization after PERST# Signal instead of the raw value of 100 ms.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://patch.msgid.link/20251020111121.31779-5-ansuelsmth@gmail.com
|
|
To clean Mediatek SoC PCIe struct, convert all the bool to a bitmap and
use a single quirks to reference all the values. This permits cleaner
addition of new quirk without having to define a new bool in the struct.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://patch.msgid.link/20251020111121.31779-4-ansuelsmth@gmail.com
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next
Marc Kleine-Budde says:
====================
pull-request: can-next 2025-10-17
The first patch is by me and adds support for an optional reset to the
m_can drivers.
Vincent Mailhol's patch targets all drivers and removes the
can_change_mtu() function, since the netdev's min and max MTU are
populated.
Markus Schneider-Pargmann contributes 4 patches to the m_can driver to
add am62 wakeup support.
The last 7 patches are by me and provide various cleanups to the m_can
driver.
* tag 'linux-can-next-for-6.19-20251017' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next:
can: m_can: m_can_get_berr_counter(): don't wake up controller if interface is down
can: m_can: m_can_tx_submit(): remove unneeded sanity checks
can: m_can: m_can_class_register(): remove error message in case devm_kzalloc() fails
can: m_can: m_can_interrupt_enable(): use m_can_write() instead of open coding it
net: m_can: convert dev_{dbg,info,err} -> netdev_{dbg,info,err}
can: m_can: hrtimer_callback(): rename to m_can_polling_timer()
can: m_can: m_can_init_ram(): make static
can: m_can: Support pinctrl wakeup state
can: m_can: Return ERR_PTR on error in allocation
can: m_can: Map WoL to device_set_wakeup_enable
dt-bindings: can: m_can: Add wakeup properties
can: treewide: remove can_change_mtu()
can: m_can: add support for optional reset
====================
Link: https://patch.msgid.link/20251017150819.1415685-1-mkl@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Convert sprintf/snprintf calls to scnprintf to better align with the
kernel development community practices [1].
Link: https://lwn.net/Articles/69419 [1]
Reviewed-by: Alexandra Winter <wintera@linux.ibm.com>
Signed-off-by: Aswin Karuvally <aswin@linux.ibm.com>
Signed-off-by: Alexandra Winter <wintera@linux.ibm.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20251017094954.1402684-1-wintera@linux.ibm.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The K1 state reduces power consumption on ICH family network controllers
during idle periods, similarly to L1 state on PCI Express NICs. Therefore,
it is recommended and enabled by default.
However, on some systems it has been observed to have adverse side
effects, such as packet loss. It has been established through debug that
the problem may be due to firmware misconfiguration of specific systems,
interoperability with certain link partners, or marginal electrical
conditions of specific units.
These problems typically cannot be fixed in the field, and generic
workarounds to resolve the side effects on all systems, while keeping K1
enabled, were found infeasible.
Therefore, add the option for users to globally disable K1 idle state on
the adapter.
Additionally, disable K1 by default for MTL and later platforms, due to
issues reported with the current configuration.
Link: https://lore.kernel.org/intel-wired-lan/CAMqyJG3LVqfgqMcTxeaPur_Jq0oQH7GgdxRuVtRX_6TTH2mX5Q@mail.gmail.com/
Link: https://lore.kernel.org/intel-wired-lan/20250626153544.1853d106@onyx.my.domain/
Link: https://lore.kernel.org/intel-wired-lan/Z_z9EjcKtwHCQcZR@mail-itl/
Link: https://github.com/QubesOS/qubes-issues/issues/9896
Link: https://bugs.launchpad.net/ubuntu/+source/linux/+bug/2115393
Signed-off-by: Vitaly Lifshits <vitaly.lifshits@intel.com>
Reviewed-by: Timo Teräs <timo.teras@iki.fi>
Tested-by: Timo Teräs <timo.teras@iki.fi>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Reviewed-by: Dima Ruinskiy <dima.ruinskiy@intel.com>
Tested-by: Avraham Koren <Avrahamx.koren@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/20251016-jk-iwl-next-2025-10-15-v2-14-ff3a390d9fc6@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Use the ice_netdev_to_pf() helper in more places and remove a bunch of
boilerplate code. Not every instance could be replaced due to use of the
netdev_priv() output or the vsi variable within a bunch of functions.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Tested-by: Rinitha S <sx.rinitha@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/20251016-jk-iwl-next-2025-10-15-v2-12-ff3a390d9fc6@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The kernel now has common statistics for transmit timestamps, so
implement them in the ice driver.
use via
ethtool -I -T eth0
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Hariprasad Kelam <hkelam@marvell.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Rinitha S <sx.rinitha@intel.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/20251016-jk-iwl-next-2025-10-15-v2-11-ff3a390d9fc6@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
As a pre-requisite to implementing timestamp statistics, start tracking
successful PTP timestamps. There already existed a trace event, but
add a counter as well so it can be displayed by the next patch.
Good count is a u64 as it is much more likely to be incremented. The
existing error stats are all u32 as before, and are less likely so will
wrap less.
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Rinitha S <sx.rinitha@intel.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/20251016-jk-iwl-next-2025-10-15-v2-10-ff3a390d9fc6@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add support for MAC/pause/RMON stats. This enables reporting hardware
statistics in a common way via:
ethtool -S eth0 --all-groups
and
ethtool --include-statistics --show-pause eth0
While doing so, add support for one new stat, receive length error
(RLEC), which is extremely unlikely to happen since most L2 frames have
a type/length field specifying a "type", and raw ethernet frames aren't
used much any longer.
NOTE: I didn't implement Ctrl aka control frame stats because the
hardware doesn't seem to implement support.
Reviewed-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Rinitha S <sx.rinitha@intel.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/20251016-jk-iwl-next-2025-10-15-v2-9-ff3a390d9fc6@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
https://gitlab.freedesktop.org/drm/xe/kernel into drm-next
Highlights:
UAPI Changes:
Loosen used tracking restriction (Matthew Auld)
New SR-IOV debugfs structure and debugfs updates (Michal Wajdeczko)
Hide the GPU madvise flag behind a VM_BIND flag (Thomas Hellström)
Always expose VRAM provisioning data on discrete GPUs (Lukasz Laguna)
Cross-subsystem Changes:
Allow VRAM mappings for userptr when used with SVM (Matthew Brost)
Driver Changes:
Allow pinning of p2p dma-buf (Thomas Hellstrom)
Use per-tile debugfs where appropriate (Michal Wajdeczko)
Add documentation for Execution Queues (Niranjana Vishwanathapura)
PF improvements (Michal Wajdeczko)
VF migration recovery redesign work (Matthew Brost)
User / Kernel VRAM partitioning (Piotr Piórkowski)
Update Tile-based messages (Michal Wajdeczko)
Allow configfs to disable specific GT types (Matt Roper)
VF provisioning improvements (Michal Wajdeczko)
Initial Xe3P support (Various people)
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Thomas Hellstrom <thomas.hellstrom@linux.intel.com>
Link: https://lore.kernel.org/r/aPXzbOb7eGbkgMrr@fedora
|
|
Refactor the ethtool ring parameter configuration logic to address two
issues: unnecessary queue resets and lost configuration changes when
the interface is down.
Previously, `gve_set_ringparam` could trigger multiple queue
destructions and recreations for a single command, as different settings
(e.g., header split, ring sizes) were applied one by one. Furthermore,
if the interface was down, any changes made via ethtool were discarded
instead of being saved for the next time the interface was brought up.
This patch centralizes the configuration logic. Individual functions
like `gve_set_hsplit_config` are modified to only validate and stage
changes in a temporary config struct.
The main `gve_set_ringparam` function now gathers all staged changes
and applies them as a single, combined configuration:
1. If the interface is up, it calls `gve_adjust_config` once.
2. If the interface is down, it saves the settings directly to the
driver's private struct, ensuring they persist and are used when
the interface is brought back up.
Signed-off-by: Ankit Garg <nktgrg@google.com>
Reviewed-by: Harshitha Ramamurthy <hramamurthy@google.com>
Reviewed-by: Jordan Rhee <jordanrhee@google.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Joshua Washington <joshwash@google.com>
Link: https://patch.msgid.link/20251017012614.3631351-1-joshwash@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
XDP programs can change the layout of an xdp_buff through
bpf_xdp_adjust_tail() and bpf_xdp_adjust_head(). Therefore, the driver
cannot assume the size of the linear data area nor fragments. Fix the
bug in mlx5 by generating skb according to xdp_buff after XDP programs
run.
Currently, when handling multi-buf XDP, the mlx5 driver assumes the
layout of an xdp_buff to be unchanged. That is, the linear data area
continues to be empty and fragments remain the same. This may cause
the driver to generate erroneous skb or triggering a kernel
warning. When an XDP program added linear data through
bpf_xdp_adjust_head(), the linear data will be ignored as
mlx5e_build_linear_skb() builds an skb without linear data and then
pull data from fragments to fill the linear data area. When an XDP
program has shrunk the non-linear data through bpf_xdp_adjust_tail(),
the delta passed to __pskb_pull_tail() may exceed the actual nonlinear
data size and trigger the BUG_ON in it.
To fix the issue, first record the original number of fragments. If the
number of fragments changes after the XDP program runs, rewind the end
fragment pointer by the difference and recalculate the truesize. Then,
build the skb with the linear data area matching the xdp_buff. Finally,
only pull data in if there is non-linear data and fill the linear part
up to 256 bytes.
Fixes: f52ac7028bec ("net/mlx5e: RX, Add XDP multi-buffer support in Striding RQ")
Signed-off-by: Amery Hung <ameryhung@gmail.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://patch.msgid.link/1760644540-899148-3-git-send-email-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
XDP programs can release xdp_buff fragments when calling
bpf_xdp_adjust_tail(). The driver currently assumes the number of
fragments to be unchanged and may generate skb with wrong truesize or
containing invalid frags. Fix the bug by generating skb according to
xdp_buff after the XDP program runs.
Fixes: ea5d49bdae8b ("net/mlx5e: Add XDP multi buffer support to the non-linear legacy RQ")
Reviewed-by: Dragos Tatulea <dtatulea@nvidia.com>
Signed-off-by: Amery Hung <ameryhung@gmail.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://patch.msgid.link/1760644540-899148-2-git-send-email-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Convert driver to use .ndo_hwtstamp_get()/.ndo_hwtstamp_set() callbacks.
.ndo_eth_ioctl() implementation becomes empty, remove it.
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Link: https://patch.msgid.link/20251016152515.3510991-8-vadim.fedorenko@linux.dev
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Convert to .ndo_hwtstamp_get()/.ndo_hwtstamp_set() callbacks.
After conversions the rest of tsnep_netdev_ioctl() becomes pure
phy_do_ioctl_running(), so remove tsnep_netdev_ioctl() and replace
it with phy_do_ioctl_running() in .ndo_eth_ioctl.
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Gerhard Engleder <gerhard@engleder-embedded.com>
Link: https://patch.msgid.link/20251016152515.3510991-7-vadim.fedorenko@linux.dev
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Convert to use .ndo_hwtstamp_get()/.ndo_hwtstamp_set() callbacks.
There is some change in the logic as well. Previously, the driver was
storing newly requested configuration regardless of whether it was
applied or not. In case of request validation error, inconsistent
configuration would be returned by the driver. New logic stores
configuration only if was properly validated and applied. It brings the
consistency between reported and actual configuration.
Signed-off-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/20251016152515.3510991-6-vadim.fedorenko@linux.dev
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Convert driver to .ndo_hwtstamp_get()/.ndo_hwtstamp_set() callbacks.
.ndo_eth_ioctl() becomes empty so remove it. Also simplify code with no
functional changes.
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Link: https://patch.msgid.link/20251016152515.3510991-5-vadim.fedorenko@linux.dev
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Convert driver to use .ndo_hwtstamp_get()/.ndo_hwtstamp_set() callbacks.
.ndo_eth_ioctl() becomes empty function, remove it.
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Link: https://patch.msgid.link/20251016152515.3510991-4-vadim.fedorenko@linux.dev
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Convert driver to use .ndo_hwtstamp_get()/.ndo_hwtstamp_set() API.
.ndo_eth_ioctl() implementation becomes pure phy_do_ioctl(), remove
it from common module, remove exported symbol and replace ndo callback.
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Link: https://patch.msgid.link/20251016152515.3510991-3-vadim.fedorenko@linux.dev
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Migrate driver to new API for HW timestamping.
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Link: https://patch.msgid.link/20251016152515.3510991-2-vadim.fedorenko@linux.dev
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
For Xe3p arch some subunits of an IP may be different. The GMD_ID
register returns the Xe3p arch and dedicates the reserved field to mark
possible subunit differences. Generally this is an under-the-hood
implementation detail that drivers don't need to worry about, but the
new Main_GAMCTRL may be enabled or not depending on those.
Those reserved bits are described for Xe3p as: "If Zero, No special case
to be handled. If Non-Zero, special case to be handled by Software
agent.". That special case is defined per Arch. So if media version is
35, also check the additional reserved bits. To avoid confusion with the
usual meaning of "reserved", define them as GMD_ID_SUBIP_FLAG_MASK.
Bspec: 74201
Signed-off-by: Balasubramani Vivekanandan <balasubramani.vivekanandan@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://lore.kernel.org/r/20251019-xe3p-gamctrl-v1-2-ad66d3c1908f@intel.com
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
|
|
Starting from Xe3p, there are two different copies of some of the GAM
registers: the traditional MCR variant at their old locations, and a
new unicast copy known as "main_gamctrl." The Xe driver doesn't use
these registers directly, but we need to instruct the GuC on which set
it should use. Since the new, unicast registers are preferred (since
they avoid the need for unnecessary MCR synchronization), set a new GuC
feature flag, GUC_CTL_MAIN_GAMCTRL_QUEUES to convey this decision. A
new helper function, xe_guc_using_main_gamctrl_queues(), is added for
use in the 3 independent places that need to handle configuration of the
new reporting queues.
The mmio write to enable the main gamctl is only done during the general
GuC upload. The gamctrl registers are not accessed by the GuC during
hwconfig load.
Last, the ADS blob for communicating the queue addresses contains both a
DPA and GGTT offset. The GuC documentation states that DPA is now MBZ
when using the MAIN_GAMCTRL queues.
Bspec: 76445, 73540
Signed-off-by: Brian Welty <brian.welty@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://lore.kernel.org/r/20251019-xe3p-gamctrl-v1-1-ad66d3c1908f@intel.com
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
|
|
Now that stmmac's PCS support is much more simple - just a matter of
configuring the control register - the basic conversion to phylink PCS
support becomes straight forward.
Create the infrastructure to setup a phylink_pcs instance for the
integrated PCS:
- add a struct stmmac_pcs to encapsulate the phylink_pcs structure,
pointer to stmmac_priv, and the core-specific base address of the PCS
registers.
- modify stmmac_priv and stmmac_mac_select_pcs() to return the embedded
phylink_pcs structure when setup and STMMAC_PCS_SGMII is in use, and
move the comment from stmmac_hw_setup() to here.
- create stmmac_pcs.c, which contains the phylink_pcs_ops structure, a
dummy .pcs_get_state() method which always reports link-down, and
.pcs_config() method, moving the call to stmmac_pcs_ctrl_ane() here,
but without indirecting through the dwmac specific core code. The
link-down behaviour mentioned above maintains the current behaviour
when phylink is used with inband but without a PCS.
This will ensure that the PCS control register is configured to the
same settings as before, but will now happen when the netdev is opened
or reusmed rather than only during probe time. However, this will be
before the .fix_mac_speed() method is called, which is critical for the
behaviour in dwmac-qcom-ethqos's ethqos_configure_sgmii() function to
be maintained.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Tested-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Tested-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://patch.msgid.link/E1v9P72-0000000AomR-3ro4@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
dwmac cores provide a feature bit to indicate when the PCS block is
present, but features are only read after the core's setup() function
has been called, meaning we can't decide whether to initialise the
integrated PCS in the setup function. Provide a new MAC core hook
for PCS initialisation, which will be called after the feature
registers have been read.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Tested-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Tested-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://patch.msgid.link/E1v9P6x-0000000AomL-3OKd@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The internal PCS registers only exist if the core is synthesized with
SGMII, TBI or RTBI support. They have no relevance for RGMII.
However, priv->hw->pcs contains a STMMAC_PCS_RGMII flag, which is set
if a PCS has been synthesized but we are operating in RGMII mode. As
the register has no effect for RGMII, there is no point calling
stmmac_pcs_ctrl_ane() in this case. Add a comment describing this
and make it conditional on STMMAC_PCS_SGMII.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Tested-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Tested-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://patch.msgid.link/E1v9P6s-0000000AomE-2pAa@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
SGMII mode does not require port-speed to be specified; this only
switches SGMII to use the MAC configuration register speed settings
and the actual value is irrelevant when the link comes up.
As it seems the intention was to support "reverse SGMII" with this
setting, but the code didn't actually configure that due to a typo,
the warning and bad DT binding documentation has led people to
specify snps,ps-speed in their DT files inappropriately.
If mac_port_sel_speed is zero, then don't complain that the speed
is invalid, as this means we're using "normal" SGMII.
This does _not_ obsolete snps,ps-speed, nor does it change the
behaviour of that property, with the exception of not making people
mistakenly believe that they need to specify this option to use
normal SGMII. There is no need to modify the binding.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Tested-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Tested-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://patch.msgid.link/E1v9P6n-0000000Aom9-2LuZ@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
After a lot of digging, it seems that the oddly named hw->ps member
is all about setting the core into reverse SGMII speed. When set to
a non-zero value, it:
1. Configures the MAC at initialisation time to operate at a specific
speed.
2. It _incorrectly_ enables the transmitter (GMAC_CONFIG_TE) which
makes no sense, rather than enabling the "transmit configuration"
bit (GMAC_CONFIG_TC).
3. It configures the SGMII rate adapter layer to retrieve its speed
setting from the MAC configuration register rather than the PHY.
In the previous commit, we removed (1) and (2) as phylink overwrites
the configuration set at that step.
Thus, the only functional aspect is (3), which is a boolean operation.
This means there is no need to store the actual speed, and just have a
boolean flag.
Convert the priv->ps member to a boolean, and rename it to
priv->reverse_sgmii_enable to make it more understandable.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Tested-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Tested-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://patch.msgid.link/E1v9P6i-0000000Aom3-1y2y@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Now that we only support one mode, simplify stmmac_check_pcs_mode().
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Tested-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Tested-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://patch.msgid.link/E1v9P6d-0000000Aolw-1T7d@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
