| Age | Commit message (Collapse) | Author |
|---|
|
Currently, per-radio attributes are set on per-phy basis, i.e., all the
radios present in a wiphy will take attributes values sent from user. But
each radio in a wiphy can get different values from userspace based on
its requirement.
To extend support to set per-radio attributes, add support to get radio
index from userspace. Add an NL attribute - NL80211_ATTR_WIPHY_RADIO_INDEX,
to get user specified radio index for which attributes should be changed.
Pass this to individual drivers, so that the drivers can use this radio
index to change per-radio attributes when necessary. Currently, per-radio
attributes identified are:
NL80211_ATTR_WIPHY_TX_POWER_LEVEL
NL80211_ATTR_WIPHY_ANTENNA_TX
NL80211_ATTR_WIPHY_ANTENNA_RX
NL80211_ATTR_WIPHY_RETRY_SHORT
NL80211_ATTR_WIPHY_RETRY_LONG
NL80211_ATTR_WIPHY_FRAG_THRESHOLD
NL80211_ATTR_WIPHY_RTS_THRESHOLD
NL80211_ATTR_WIPHY_COVERAGE_CLASS
NL80211_ATTR_TXQ_LIMIT
NL80211_ATTR_TXQ_MEMORY_LIMIT
NL80211_ATTR_TXQ_QUANTUM
By default, the radio index is set to -1. This means the attribute should
be treated as a global configuration. If the user has not specified any
index, then the radio index passed to individual drivers would be -1. This
would indicate that the attribute applies to all radios in that wiphy.
Signed-off-by: Roopni Devanathan <quic_rdevanat@quicinc.com>
Link: https://patch.msgid.link/20250615082312.619639-2-quic_rdevanat@quicinc.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Add video_device_release() in label 'err_m2m' to release the memory
allocated by video_device_alloc() and prevent potential memory leaks.
Remove the reduntant code in label 'err_m2m'.
Fixes: a8ef0488cc59 ("media: imx: add csc/scaler mem2mem device")
Cc: stable@vger.kernel.org
Signed-off-by: Haoxiang Li <haoxiang_li2024@163.com>
Reviewed-by: Dan Carpenter <dan.carpenter@linaro.org>
Signed-off-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
|
|
On errors, the rkvdec chip self resets. This can clear the addresses
programmed in the iommu. This case is signaled by the
RKVDEC_SOFTRESET_RDY status bit.
Since the iommu framework does not have a restore functionality, and
as recommended by the iommu subsystem maintainers, this patch
restores the iommu programming by attaching and detaching an empty
domain, which will clear and restore the default domain.
Suggested-by: Detlev Casanova <detlev.casanova@collabora.com>
Tested-by: Detlev Casanova <detlev.casanova@collabora.com>
Reviewed-by: Detlev Casanova <detlev.casanova@collabora.com>
Signed-off-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
|
|
If VPU supports untiled output, it actually supports several different
YUV 4:2:0 layouts, namely NV12, NV21, YUV420 and YVU420.
Add support for all of them.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Paul Kocialkowski <paulk@sys-base.io>
Signed-off-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
[hverkuil: add 'default' case to switch to fix warning with old compiler]
|
|
After commit 6f110a5e4f99 ("Disable SLUB_TINY for build testing"), which
causes CONFIG_KASAN to be enabled in allmodconfig again, arm64
allmodconfig builds with older versions of clang (15 through 17) show an
instance of -Wframe-larger-than (which breaks the build with
CONFIG_WERROR=y):
drivers/staging/rtl8723bs/core/rtw_security.c:1287:5: error: stack frame size (2208) exceeds limit (2048) in 'rtw_aes_decrypt' [-Werror,-Wframe-larger-than]
1287 | u32 rtw_aes_decrypt(struct adapter *padapter, u8 *precvframe)
| ^
This comes from aes_decipher() being inlined in rtw_aes_decrypt().
Running the same build with CONFIG_FRAME_WARN=128 shows aes_cipher()
also uses a decent amount of stack, just under the limit of 2048:
drivers/staging/rtl8723bs/core/rtw_security.c:864:19: warning: stack frame size (1952) exceeds limit (128) in 'aes_cipher' [-Wframe-larger-than]
864 | static signed int aes_cipher(u8 *key, uint hdrlen,
| ^
-Rpass-analysis=stack-frame-layout only shows one large structure on the
stack, which is the ctx variable inlined from aes128k128d(). A good
number of the other variables come from the additional checks of
fortified string routines, which are present in memset(), which both
aes_cipher() and aes_decipher() use to initialize some temporary
buffers. In this case, since the size is known at compile time, these
additional checks should not result in any code generation changes but
allmodconfig has several sanitizers enabled, which may make it harder
for the compiler to eliminate the compile time checks and the variables
that come about from them.
The memset() calls are just initializing these buffers to zero, so use
'= {}' instead, which is used all over the kernel and does the exact
same thing as memset() without the fortify checks, which drops the stack
usage of these functions by a few hundred kilobytes.
drivers/staging/rtl8723bs/core/rtw_security.c:864:19: warning: stack frame size (1584) exceeds limit (128) in 'aes_cipher' [-Wframe-larger-than]
864 | static signed int aes_cipher(u8 *key, uint hdrlen,
| ^
drivers/staging/rtl8723bs/core/rtw_security.c:1271:5: warning: stack frame size (1456) exceeds limit (128) in 'rtw_aes_decrypt' [-Wframe-larger-than]
1271 | u32 rtw_aes_decrypt(struct adapter *padapter, u8 *precvframe)
| ^
Cc: stable@vger.kernel.org
Fixes: 554c0a3abf21 ("staging: Add rtl8723bs sdio wifi driver")
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Dan Carpenter <dan.carpenter@linaro.org>
Link: https://lore.kernel.org/r/20250609-rtl8723bs-fix-clang-arm64-wflt-v1-1-e2accba43def@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This improves code readability by using the standard kernel macro
for min/max value selection while maintaining identical functionality.
Signed-off-by: Yuesong Li <liyuesong@vivo.com>
Link: https://lore.kernel.org/r/20250619080822.677662-1-liyuesong@vivo.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Rename 'hwCursor' to 'hw_cursor' to
conform with kernel style guidelines as reported by checkpatch.pl
CHECK: Avoid CamelCase: <hwCursor>
Signed-off-by: Kisub Choe <kisub.choe.0x1@gmail.com>
Link: https://lore.kernel.org/r/20250618143342.6517-1-kisub.choe.0x1@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Chips that use this driver are 2.4 GHz only. Remove some code that is
executed only for 5 GHz (channel > 14) . This addresses the following
TODO item:
- find and remove any code for other chips that is left over
Signed-off-by: Michael Straube <straube.linux@gmail.com>
Reviewed-by: Hans de Goede <hansg@kernel.org>
Link: https://lore.kernel.org/r/20250615123859.41922-1-straube.linux@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Remove exit label and return statement from a void function.
After the exit label no cleanup is done, so it is safe to remove it
and return early in the only place where the label is used.
This simplifies the code and clears a checkpatch warning.
WARNING: void function return statements are not generally useful
Signed-off-by: Michael Straube <straube.linux@gmail.com>
Reviewed-by: Hans de Goede <hansg@kernel.org>
Link: https://lore.kernel.org/r/20250615123758.41869-1-straube.linux@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
As of commit 92ac7de3175e3 ("gpiolib: don't allow setting values on input
lines"), the GPIO core makes sure values cannot be set on input lines.
Remove the unnecessary check.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Rui Miguel Silva <rui.silva@linaro.org>
Link: https://lore.kernel.org/r/20250610152036.86099-1-brgl@bgdev.pl
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Ensure that all structs have a size that is an integral mutliple
of 32 bits.
Change trailing single bit field to __u32 in gpib_open_dev_ioctl
Add byte padding to gpib_serial_poll_ioctl and gpib_request_service2
Add bit padding to gpib_board_info_ioctl and gpib_ppoll_config_ioctl
Signed-off-by: Dave Penkler <dpenkler@gmail.com>
Link: https://lore.kernel.org/r/20250603184320.30594-5-dpenkler@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Change unsigned int to __u32,
int to __s32
and short to __s16
Signed-off-by: Dave Penkler <dpenkler@gmail.com>
Link: https://lore.kernel.org/r/20250603184320.30594-4-dpenkler@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add the functions and enums needed only by the kernel drivers
that were removed from the uapi/gpib.h include file to a separate
local include file.
Include this new file in the gpibP.h local include file.
Signed-off-by: Dave Penkler <dpenkler@gmail.com>
Link: https://lore.kernel.org/r/20250603184320.30594-3-dpenkler@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Remove enums and functions that do not need to be shared
with user space.
Remove enums and functions that are not needed in the kernel drivers.
Signed-off-by: Dave Penkler <dpenkler@gmail.com>
Link: https://lore.kernel.org/r/20250603184320.30594-2-dpenkler@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
As we no longer have any drivers depending on BROKEN in Kconfig
remove the fix broken driver line.
Add a list of checkpatch checks/warning that should be ignored.
Signed-off-by: Dave Penkler <dpenkler@gmail.com>
Link: https://lore.kernel.org/r/20250521160830.30454-1-dpenkler@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
vme_bus_match takes a const pointer and casts it away with
container_of() which is generally not a good idea. Fix this up by
properly marking the output as const.
Link: https://lore.kernel.org/r/2025052132-giddiness-slain-5ba1@gregkh
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Adhere to Linux kernel coding style.
Reported by checkpatch:
CHECK: Alignment should match open parentheses
Signed-off-by: Milos Puric <milospuric856@gmail.com>
Link: https://lore.kernel.org/r/aC3UOPYv8HmzRvij@milos-ThinkPad-T14-Gen-3
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This code (tty_get -> vhangup -> tty_put) is repeated on few places.
Introduce a helper similar to tty_port_tty_hangup() (asynchronous) to
handle even vhangup (synchronous).
And use it on those places.
In fact, reuse the tty_port_tty_hangup()'s code and call tty_vhangup()
depending on a new bool parameter.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Cc: Karsten Keil <isdn@linux-pingi.de>
Cc: David Lin <dtwlin@gmail.com>
Cc: Johan Hovold <johan@kernel.org>
Cc: Alex Elder <elder@kernel.org>
Cc: Oliver Neukum <oneukum@suse.com>
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Cc: Luiz Augusto von Dentz <luiz.dentz@gmail.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20250611100319.186924-2-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Move this API to the canonical timer_*() namespace.
[ tglx: Redone against pre rc1 ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/all/aB2X0jCKQO56WdMt@gmail.com
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char / misc / iio driver updates from Greg KH:
"Here is the big char/misc/iio and other small driver subsystem pull
request for 6.16-rc1.
Overall, a lot of individual changes, but nothing major, just the
normal constant forward progress of new device support and cleanups to
existing subsystems. Highlights in here are:
- Large IIO driver updates and additions and device tree changes
- Android binder bugfixes and logfile fixes
- mhi driver updates
- comedi driver updates
- counter driver updates and additions
- coresight driver updates and additions
- echo driver removal as there are no in-kernel users of it
- nvmem driver updates
- spmi driver updates
- new amd-sbi driver "subsystem" and drivers added
- rust miscdriver binding documentation fix
- other small driver fixes and updates (uio, w1, acrn, hpet,
xillybus, cardreader drivers, fastrpc and others)
All of these have been in linux-next for quite a while with no
reported problems"
* tag 'char-misc-6.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (390 commits)
binder: fix yet another UAF in binder_devices
counter: microchip-tcb-capture: Add watch validation support
dt-bindings: iio: adc: Add ROHM BD79100G
iio: adc: add support for Nuvoton NCT7201
dt-bindings: iio: adc: add NCT7201 ADCs
iio: chemical: Add driver for SEN0322
dt-bindings: trivial-devices: Document SEN0322
iio: adc: ad7768-1: reorganize driver headers
iio: bmp280: zero-init buffer
iio: ssp_sensors: optimalize -> optimize
HID: sensor-hub: Fix typo and improve documentation
iio: admv1013: replace redundant ternary operator with just len
iio: chemical: mhz19b: Fix error code in probe()
iio: adc: at91-sama5d2: use IIO_DECLARE_BUFFER_WITH_TS
iio: accel: sca3300: use IIO_DECLARE_BUFFER_WITH_TS
iio: adc: ad7380: use IIO_DECLARE_DMA_BUFFER_WITH_TS
iio: adc: ad4695: rename AD4695_MAX_VIN_CHANNELS
iio: adc: ad4695: use IIO_DECLARE_DMA_BUFFER_WITH_TS
iio: introduce IIO_DECLARE_BUFFER_WITH_TS macros
iio: make IIO_DMA_MINALIGN minimum of 8 bytes
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging driver updates from Greg KH:
"Here is the "big" set of staging driver changes for 6.16-rc1. Included
in here are:
- gpib driver cleanups and updates.
This subsystem is _almost_ ready to be merged into the main portion
of the kernel tree. Hopefully should happen in the next kernel
merge cycle if all goes well.
- sm750fb driver cleanups
- rtl8723bs driver cleanups
- other small driver cleanups for coding style issues
All of these have been in for over 2 weeks with no reported issues"
* tag 'staging-6.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (203 commits)
staging: rtl8723bs: remove unnecessary braces for single statement blocks
staging: rtl8723bs: Removed multiple blank lines of rtw_pwrctrl.c
staging: sm750fb: rename `hw_sm750le_setBLANK`
staging: sm750fb: rename `hw_sm750_setBLANK`
staging: sm750fb: rename `hw_sm750_setColReg`
staging: sm750fb: rename `hw_sm750_crtc_setMode`
staging: sm750fb: rename `hw_sm750_crtc_checkMode`
staging: sm750fb: rename `hw_sm750_output_setMode`
staging: sm750fb: rename `hw_sm750le_deWait`
staging: sm750fb: rename `hw_sm750_deWait`
staging: sm750fb: rename `hw_sm750_initAccel`
staging: gpib: switch to kmalloc(sizeof(*status))
staging: gpib: Fix secondary address restriction
staging: gpib: Fix uapi include header guard name
staging: gpib: Avoid unused variable warning
staging: gpib: Declare driver entry points static
staging: gpib: Fix PCMCIA config identifier
staging: gpib: Avoid unused variable warnings
staging: gpib: Fix lpvo request_system_control
staging: sm750fb: rename sm750_hw_cursor_setData2
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- v4l2-core fix: V4L2_BUF_TYPE_VIDEO_OVERLAY is capture, not output
- New driver: Amlogic C3 ISP
- New sensor drivers: ST VD55G1 and VD56G3, OmniVision OV02C10
- amlogic: c3-mipi-csi2: Handle 64-bits division
- a fix for 64-bits division at the amlogic c3-mipi-csi2 driver
- Changes at atomisp to support mainline mt9m114 driver and remove
deprecated GPIO APIs
- various cleanups, fixes and enhancements
* tag 'media/v6.16-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (314 commits)
media: rkvdec: h264: Support High 10 and 4:2:2 profiles
media: rkvdec: Add get_image_fmt ops
media: rkvdec: Initialize the m2m context before the controls
media: rkvdec: h264: Limit minimum profile to constrained baseline
media: mediatek: jpeg: support 34bits
media: verisilicon: Free post processor buffers on error
media: platform: mtk-mdp3: Remove unused mdp_get_plat_device
media: amlogic: c3-mipi-csi2: Handle 64-bits division
media: uvcvideo: Use dev_err_probe for devm_gpiod_get_optional
media: uvcvideo: Fix deferred probing error
media: uvcvideo: Rollback non processed entities on error
media: uvcvideo: Send control events for partial succeeds
media: uvcvideo: Return the number of processed controls
media: uvcvideo: Do not turn on the camera for some ioctls
media: uvcvideo: Make power management granular
media: uvcvideo: Increase/decrease the PM counter per IOCTL
media: uvcvideo: Create uvc_pm_(get|put) functions
media: uvcvideo: Keep streaming state in the file handle
Documentation: media: Add documentation file c3-isp.rst
Documentation: media: Add documentation file metafmt-c3-isp.rst
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer cleanups from Thomas Gleixner:
"Another set of timer API cleanups:
- Convert init_timer*(), try_to_del_timer_sync() and
destroy_timer_on_stack() over to the canonical timer_*()
namespace convention.
There is another large conversion pending, which has not been included
because it would have caused a gazillion of merge conflicts in next.
The conversion scripts will be run towards the end of the merge window
and a pull request sent once all conflict dependencies have been
merged"
* tag 'timers-cleanups-2025-05-25' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
treewide, timers: Rename destroy_timer_on_stack() as timer_destroy_on_stack()
treewide, timers: Rename try_to_del_timer_sync() as timer_delete_sync_try()
timers: Rename init_timers() as timers_init()
timers: Rename NEXT_TIMER_MAX_DELTA as TIMER_NEXT_MAX_DELTA
timers: Rename __init_timer_on_stack() as __timer_init_on_stack()
timers: Rename __init_timer() as __timer_init()
timers: Rename init_timer_on_stack_key() as timer_init_key_on_stack()
timers: Rename init_timer_key() as timer_init_key()
|
|
ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/jic23/iio into char-misc-next
Jonathan writes:
IIO: New device support, features and cleanup for 6.16 - take 2
Note - last minute rebase was to drop a typo patch that I'd accidentally
picked up (in the microblaze arch Kconfig)
Take 2 is due to that rebase messing up some fixes tags that were
referring to patches after that point.
There is a known merge conflict due to changes in neighbouring lines.
Stephen's resolution in linux-next is:
https://lore.kernel.org/linux-next/20250506155728.65605bae@canb.auug.org.au/
Added 3 named IIO reviewers to MAINTAINERS. This is a reflection of those
who have been doing much of this work for some time. Lars-Peter is
removed from the entry having moved on to other topics. Thanks
Nuno, David and Andy for stepping up and Lars-Peter for all your
hard work in the past!
Includes the usual mix of new device support, features and general
cleanup.
This time we also have some tree wide changes.
- Rip out the iio_device_claim_direct_scoped() as it proved hard to work
with. This series includes quite a few related cleanups such as use
of guard or factoring code out to allow direct returns.
- Switch from iio_device_claim/release_direct_mode() to new
iio_device_claim/release_direct() which is structured so that sparse
can warn on failed releases. There were a few false positives but
those were mostly in code that benefited from being cleaned up as part
of this process.
- Introduce iio_push_to_buffers_with_ts() to replace the _timestamp()
version over time. This version takes the size of the supplied buffer
which the core checks is at least as big as expected by calculation
from channel descriptions of those channels enabled. Use this in
an initial set of drivers.
- Add macros for IIO_DECLARE_BUFFER_WITH_TS() and
IIO_DECLARE_DMA_BUFFER_WITH_TS() to avoid lots of fiddly code to ensure
correctly aligned buffers for timestamps being added onto the end of
channel data.
New device support
------------------
adi,ad3530r
- New driver for AD3530, AD3530R, AD3531 and AD3531R DACs with
programmable gain controls. R variants have internal references.
adi,ad7476
- Add support (dt compatible only) for the Rohm BU79100G ADC which is
fully compatible with the ti,ads7866.
adi,ad7606
- Support ad7606c-16 and ad7606c-18 devices. Includes switch to dynamic
channel information allocation.
adi,ad7380
- Add support for the AD7389-4
dfrobot,sen0322
- New driver for this oxygen sensor.
mediatek,mt2701-auxadc
- Add binding for MT6893 which is fully compatible with already supported
MT8173.
meson-saradc
- Support the GXLX SoCs. Mostly this is a workaround for some unrelated
clock control bits found in the ADC register map.
nuvoton,nct7201
- New driver for NCT7201 and NCT7202 I2C ADCs.
rohm,bd79124
- New driver for this 12-bit, 8-channel SAR ADC.
- Switch to new set_rv etc gpio callbacks that were added in 6.15.
rohm,bd79703
- Add support for BD79700, BD79701 and BD79702 DACs that have subsets of
functionality of the already supported bd79703. Included making this
driver suitable for support device variants.
st,stm32-lptimer
- Add support for stm32pm25 to this trigger.
Features
--------
Beyond IIO
- Property iterator for named children.
core
- Enable writes for 64 bit integers used for standard IIO ABI elements.
Previously these could be read only.
- Helper library that should avoid code duplication for simpler ADC
bindings that have a child node per channel.
- Enforce that IIO_DMA_MINALIGN is always at least 8 (almost always true
and simplifies code on all significant architectures)
core/backend
- Add support to control source of data - useful when the HDL includes
things like generated ramps for testing purposes. Enable this for
adi-axi-dac
adi,ad3552-hs
- Add debugfs related callbacks to allow debug access to register contents.
adi,ad4000
- Support SPI offload with appropriate FPGA firmware along with improving
documentation.
adi,ad7293
- Add support for external reference voltage.
adi,ad7606
- Support SPI offload.
adi,ad7768-1
- Support reset GPIO.
adi,admv8818
- Support filter frequencies beyond 2^32.
adi,adxl345
- Add single and double tap events.
hid-sensor-prox
- Support 16-bit report sizes as seen on some Intel platforms.
invensense,icm42600
- Enable use of named interrupts to avoid problems with some wiring choices.
Get the interrupt by name, but fallback to previous assumption on the first
being INT1 if no names are supplied.
microchip,mcp3911
- Add reset gpio support.
rohm,bh7150
- Add reset gpio support.
st,stm32
- Add support to control oversampling.
ti,adc128s052
- Add support for ROHM BD79104 which is early compatible with the TI
parts already supported by this driver. Includes some general driver
cleanup and a separate dt binding.
- Simplify reference voltage handling by assuming it is fixed after enabling
the supply.
winsen,mhz19b
- New driver for this C02 sensor.
Cleanup and minor fixes
-----------------------
dt-bindings
- Correct indentation and style for DTS examples.
- Use unevalutateProperties for SPI devices instead of additionalProperties
to allow generic SPI properties from spi-peripheral-props.yaml
ABI Docs
- Add missing docs for sampling_frequency when it applies only to events.
Treewide
- Various minor tweaks, comment fixes and similar.
- Sort TI ADCs in Kconfig that had gotten out of order.
- Switch various drives that provide GPIO chip functionality to the new
callbacks with return values.
- Standardize on { } formatting for all array sentinels.
- Make use of aligned_s64 in a few places to replace either wrong types
or manually defined equivalents.
- Drop places where spi bits_per_word is set to 8 because that is the
default anyway.
adi,ad_sigma_delta library
- Avoid a potential use of uninitialized data if reg_size has a value
that is not supported (no drivers hit this but it is reasonable hardening)
adi,ad4030
- Add error checking for scan types and no longer store it in state.
- Rework code to reduce duplication.
- Move setting the mode from buffer preenable() to update_scan_mode(),
better matching expected semantics of the two different callbacks.
- Improve data marshalling comments.
adi,ad4695
- Use u16 for buffer elements as oversampling is not yet supported except
with SPI offload (which doesn't use this path).
adi,ad5592r
- Clean up destruction of mutexes.
- Use lock guards to simplify code (later patch fixes a missed unlock)
adi,ad5933
- Correct some incorrect settling times.
adi,ad7091
- Deduplicate handling of writable vs volatile registers as they are the
inverse of each other for this device.
adi,ad7124
- Fix 3db Filter frequency.
- Remove ability to directly write the filter frequency (which was broken)
- Register naming improvements.
adi,ad7606
- Add a missing return value check.
- Fill in max sampling rates for all chips.
- Use devm_mutex_init()
- Fix up some kernel-doc formatting issues.
- Remove some camel case that snuck in.
- Drop setting address field in channels as easily established from other
fields.
- Drop unnecessary parameter to ad76060_scale_setup_cb_t.
adi,ad7768-1
- Convert to regmap.
- Factor out buffer allocation.
- Tidy up headers.
adi,ad7944
- Stop setting bits_per_word in SPI xfers with no data.
adi,ad9832
- Add of_device_id table rather than just relying on fallbacks.
- Use FIELD_PREP() to set values of fields.
adi,admv1013
- Cleanup a pointless ternary.
adi,admv8818
- Fix up LPF Band 5 frequency which was slightly wrong.
- Fix an integer overflow.
- Fix range calculation
adi,adt7316
- Replace irqd_get_trigger_type(irq_get_irq_data()) with simpler
irq_get_trigger_type()
adi,adxl345
- Use regmap cache instead of various state variables that were there to
reduce bus accesses.
- Make regmap return value checking consistent across all call sites.
adi,axi-dac
- Add a check on number of channels (0 to 15 valid)
allwinner,sun20i
- Use new adc-helpers to replace local parsing code for channel nodes.
bosch,bmp290
- Move to local variables for sensor data marshalling removing the need
for a messy definition that has to work for all supported parts.
Follow up fix adds a missing initialization.
dynaimage,al3010 and dynaimage,al3320a
- Various minor cleanup to bring these drivers inline with reviewed feedback
given on a new driver.
- Fix an error path in which power down is not called when it should be.
- Switch to regmap.
google,cros_ec
- Fix up a flexible array in middle of structure warning.
- Flush fifo when changing the timeout to avoid potential long wait
for samples.
hid-sensor-rotation
- Remove an __aligned(16) marking that doesn't seem to be justified.
kionix,kxcjk-1013
- Deduplicate code for setting up interrupts.
microchip,mcp3911
- Fix handling of conversion results register which differs across supported
devices.
idt,zopt2201
- Avoid duplicating register lists as all volatile registers are the
inverse of writeable registers on this device.
renesas,rzg2l
- Use new adc-helpers to replace local parsing code for channel nodes.
ti,ads1298
- Fix a missing Kconfig dependency.
* tag 'iio-for-6.16a-take2' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/jic23/iio: (260 commits)
dt-bindings: iio: adc: Add ROHM BD79100G
iio: adc: add support for Nuvoton NCT7201
dt-bindings: iio: adc: add NCT7201 ADCs
iio: chemical: Add driver for SEN0322
dt-bindings: trivial-devices: Document SEN0322
iio: adc: ad7768-1: reorganize driver headers
iio: bmp280: zero-init buffer
iio: ssp_sensors: optimalize -> optimize
HID: sensor-hub: Fix typo and improve documentation
iio: admv1013: replace redundant ternary operator with just len
iio: chemical: mhz19b: Fix error code in probe()
iio: adc: at91-sama5d2: use IIO_DECLARE_BUFFER_WITH_TS
iio: accel: sca3300: use IIO_DECLARE_BUFFER_WITH_TS
iio: adc: ad7380: use IIO_DECLARE_DMA_BUFFER_WITH_TS
iio: adc: ad4695: rename AD4695_MAX_VIN_CHANNELS
iio: adc: ad4695: use IIO_DECLARE_DMA_BUFFER_WITH_TS
iio: introduce IIO_DECLARE_BUFFER_WITH_TS macros
iio: make IIO_DMA_MINALIGN minimum of 8 bytes
iio: pressure: zpa2326_spi: remove bits_per_word = 8
iio: pressure: ms5611_spi: remove bits_per_word = 8
...
|
|
The AD5933 datasheet (Table 13) lists the maximum cycles to be 0x7FC
(2044).
Clamp the user input to the maximum effective value of 0x7FC cycles.
Fixes: f94aa354d676 ("iio: impedance-analyzer: New driver for AD5933/4 Impedance Converter, Network Analyzer")
Cc: stable@vger.kernel.org
Signed-off-by: Gabriel Shahrouzi <gshahrouzi@gmail.com>
Reviewed-by: Marcelo Schmitt <marcelo.schmitt1@gmail.com>
Link: https://patch.msgid.link/20250420013009.847851-1-gshahrouzi@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
This is a leftover from the patch: commit 566564e80b0e ("staging: iio:
ad9832: use clock framework for clock reference").
The AD9832 driver uses the Common Clock Framework (CCF) to obtain the
master clock (MCLK) frequency rather than relying on a frequency value
passed from platform data.
Signed-off-by: Gabriel Shahrouzi <gshahrouzi@gmail.com>
Link: https://patch.msgid.link/20250417173333.607844-1-gshahrouzi@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Use bitfield and bitmask macros to clearly specify AD9832 SPI
command fields to make register write code more readable.
Suggested-by: Marcelo Schmitt <marcelo.schmitt1@gmail.com>
Reviewed-by: Marcelo Schmitt <marcelo.schmitt1@gmail.com>
Signed-off-by: Siddharth Menon <simeddon@gmail.com>
Link: https://patch.msgid.link/20250416140259.13431-1-simeddon@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Remove all unnecessary braces for single-statement blocks in
`os_dep/recv_linux.c` to conform to code style rules.
Warnings reported by checkpatch.pl:
* WARNING: braces {} are not necessary for single statement blocks
* WARNING: braces {} are not necessary for any arm of this statement
Signed-off-by: David Tadokoro <davidbtadokoro@usp.br>
Link: https://lore.kernel.org/r/20250521075831.485199-1-davidbtadokoro@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Removed multiple blank lines in file rtw_pwrctrl.c
Found by checkpatch.pl
Signed-off-by: Rogério Fernandes Pereira <rfp2005@gmail.com>
Link: https://lore.kernel.org/r/20250503202430.6053-1-rfp2005@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Rename `hw_sm750le_setBLANK` to `hw_sm750le_set_blank` to conform with
kernel style guidelines as reported by checkpatch.pl
CHECK: Avoid CamelCase: <hw_sm750le_setBLANK>
Signed-off-by: Eric Florin <ericflorin@google.com>
Link: https://lore.kernel.org/r/b49d1a00628a3475fdfbff4055d8347d35a802a9.1747619816.git.ericflorin@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Rename `hw_sm750_setBLANK` to `hw_sm750_set_blank` to conform with
kernel style guidelines as reported by checkpatch.pl
CHECK: Avoid CamelCase: <hw_sm750_setBLANK>
Signed-off-by: Eric Florin <ericflorin@google.com>
Link: https://lore.kernel.org/r/e00a39ffba89e000fdf8dc277166297d995aa891.1747619816.git.ericflorin@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Rename `hw_sm750_setColReg` to `hw_sm750_set_col_reg` to conform with
kernel style guidelines as reported by checkpatch.pl
CHECK: Avoid CamelCase: <hw_sm750_setColReg>
Signed-off-by: Eric Florin <ericflorin@google.com>
Link: https://lore.kernel.org/r/3d4bb87742eee4a6792bbdae893256f621ffffe6.1747619816.git.ericflorin@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Rename `hw_sm750_crtc_setMode` to `hw_sm750_crtc_set_mode` to conform
with kernel style guidelines as reported by checkpatch.pl
CHECK: Avoid CamelCase: <hw_sm750_crtc_setMode>
Signed-off-by: Eric Florin <ericflorin@google.com>
Link: https://lore.kernel.org/r/40d4a1f5b05bcb0eefdd787b9df329fceb96105e.1747619816.git.ericflorin@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Rename `hw_sm750_crtc_checkMode` to `hw_sm750_crtc_check_mode` to
conform with kernel style guidelines as reported by checkpatch.pl
CHECK: Avoid CamelCase: <hw_sm750_crtc_checkMode>
Signed-off-by: Eric Florin <ericflorin@google.com>
Link: https://lore.kernel.org/r/546e9abb8eac1be75f47b51460ab69a5736d8a99.1747619816.git.ericflorin@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Rename `hw_sm750_output_setMode` to `hw_sm750_output_set_mode` to
conform with kernel style guidelines as reported by checkpatch.pl
CHECK: Avoid CamelCase: <hw_sm750_output_setMode>
Signed-off-by: Eric Florin <ericflorin@google.com>
Link: https://lore.kernel.org/r/32daa589cf80d2f6f67ed257aa9397128a5458d2.1747619816.git.ericflorin@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Rename `hw_sm750le_deWait` to `hw_sm750le_de_wait` to conform with
kernel style guidelines as reported by checkpatch.pl
CHECK: Avoid CamelCase: <hw_sm750le_deWait>
Signed-off-by: Eric Florin <ericflorin@google.com>
Link: https://lore.kernel.org/r/0e5332f7758ad24cc5bca36671fd811c87881db7.1747619816.git.ericflorin@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Rename `hw_sm750_deWait` to `hw_sm750_de_wait` to conform with kernel
style guidelines as reported by checkpatch.pl
CHECK: Avoid CamelCase: <hw_sm750_deWait>
Signed-off-by: Eric Florin <ericflorin@google.com>
Link: https://lore.kernel.org/r/2d94a42ca51de9fddddb64f74e217dfb2e0c7d1c.1747619816.git.ericflorin@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Rename `hw_sm750_initAccel` to `hw_sm750_init_accel` to conform with
kernel style guidelines as reported by checkpatch.pl
CHECK: Avoid CamelCase: <hw_sm750_initAccel>
Signed-off-by: Eric Florin <ericflorin@google.com>
Link: https://lore.kernel.org/r/3c84dccaf38161d6de6ff560d4f10bb3d344cc51.1747619816.git.ericflorin@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Fix checkpatch warning:
Prefer kmalloc(sizeof(*status)...) over
kmalloc(sizeof(struct gpib_status_byte)...)
Signed-off-by: Andreas Kleinbichler <andi.kleinbichler@gmail.com>
Link: https://lore.kernel.org/r/aCdY-OgvoTUjcIeF@andreas-VirtualBox
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
GPIB secondary addresses have valid values between 0 and 31
inclusive. The Make Secondary Address function MSA, used to form
the protocol byte, was using the gpib_address_restrict function
erroneously restricting the address range to 0 through 30.
Remove the call to gpib_address_restrict and simply trim the
address to 5 bits.
Fixes: 2da03e7e31aa ("staging: gpib: Add user api include files")
Signed-off-by: Dave Penkler <dpenkler@gmail.com>
Link: https://lore.kernel.org/r/20250520155100.5808-1-dpenkler@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When gpib_user.h was renamed to gpio.h the include guard name was
not changed accordingly.
Change the include guard name to correspond with the file name
and cleanup the comments after the #endif.
Fixes: c7184cbf5530 ("staging: gpib: Rename common include file")
Signed-off-by: Dave Penkler <dpenkler@gmail.com>
Link: https://lore.kernel.org/r/20250509113014.9105-1-dpenkler@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This addresses a warning produced by make W=1 with the configuration
parameter CONFIG_GPIB_PCMCIA=y
ines/ines_gpib.c:1115:28: warning: variable 'dev' set but not used [-Wunused-but-set-variable]
Remove the declaration and assignment of the unused variable.
Signed-off-by: Dave Penkler <dpenkler@gmail.com>
Link: https://lore.kernel.org/r/20250502072150.32714-4-dpenkler@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Many of this driver's entry points were unecessarily not declared
static.
Remove the declarations from the include file.
Make the declarations static in the .c file.
Remove an uneccessary forward declaration in the .c file.
Signed-off-by: Dave Penkler <dpenkler@gmail.com>
Link: https://lore.kernel.org/r/20250502072150.32714-3-dpenkler@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The PCMCIA config identifier in the ines_exit_module function
was never changed because it was misspelled in the original commit.
Update the config parameter to use the correct identifier from
gpib/Kconfig
Fixes: bb1bd92fa0f2 ("staging: gpib: Add ines GPIB driver")
Signed-off-by: Dave Penkler <dpenkler@gmail.com>
Link: https://lore.kernel.org/r/20250502072150.32714-2-dpenkler@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add support and enable decoding of H264 High 10 and 4:2:2 profiles.
Decoded CAPTURE buffer width is aligned to 64 pixels to accommodate HW
requirement of 10-bit format buffers, fixes decoding of all the 4:2:2
and 10bit 4:2:2 flusters tests except two stream that present some
visual artifacts.
- Hi422FREXT17_SONY_A
- Hi422FREXT19_SONY_A
The get_image_fmt() ops is implemented to select an image format
required for the provided SPS control, and returns RKVDEC_IMG_FMT_ANY
for other controls.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Tested-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Tested-by: Christopher Obbard <chris.obbard@collabora.com>
Signed-off-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
|
|
Add support for a get_image_fmt() ops that returns the required image
format.
The CAPTURE format is reset when the required image format changes and
the buffer queue is not busy.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Tested-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Reviewed-by: Jonas Karlman <jonas@kwiboo.se>
Co-developed-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
|
|
Setting up the control handler calls into .s_ctrl ops. While validating
the controls the ops may need to access some of the context state, which
could lead to a crash if not properly initialized.
Signed-off-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
|
|
Neither the hardware nor the kernel API support FMO/ASO features
required by the full baseline profile. Therefore limit the minimum
profile to the constrained baseline profile explicitly.
Suggested-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Sebastian Fricke <sebastian.fricke@collabora.com>
Signed-off-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
|
|
We need the staging changes in here as well
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging driver fixes from Greg KH:
"Here are three small staging driver fixes for 6.15-rc6. These are:
- bcm2835-camera driver fix
- two axis-fifo driver fixes
All of these have been in linux-next for a few weeks with no reported
issues"
* tag 'staging-6.15-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging: axis-fifo: Remove hardware resets for user errors
staging: axis-fifo: Correct handling of tx_fifo_depth for size validation
staging: bcm2835-camera: Initialise dev in v4l2_dev
|
