| Age | Commit message (Collapse) | Author |
|---|
|
If the MST payload allocation failed, enabling the output also failed
most probably, so send a uevent accordinly requesting the user to retry
the modeset. While at it remove the driver specific debug message, there
is already one printed by drm_dp_add_payload_part1().
Reviewed-by: Suraj Kandpal <suraj.kandpal@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240722165503.2084999-12-imre.deak@intel.com
|
|
The MST topology probing depends on the maximum link parameters -
programmed to DPCD if required by a follow-up patch - so make sure these
parameters are up-to-date before configuring and probing the MST
topology.
Reviewed-by: Suraj Kandpal <suraj.kandpal@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240722165503.2084999-11-imre.deak@intel.com
|
|
On MST links - at least for some MST branch devices - the list of modes
returned to users on an enabled link depends on the current link
rate/lane count parameters (besides the DPRX link capabilities, any MST
branch BW limit and the maximum link parameters reduced after LT
failures). In particular the MST branch BW limit may depend on the link
rate/lane count parameters programmed to DPCD. After an LT failure and
limiting the maximum link parameters accordingly, users should see a
mode list reflecting these new limits. However with the current fallback
order this isn't ensured, as the new limit could allow for modes
requiring a higher link BW, but these modes will be filtered out due to
the enabled link's lower link BW.
Ensure that the mode list changes in a consistent way after a link
training failure and reducing the link parameters by changing the
fallback order on MST links to happen in BW order.
v2:
- s/INTEL_DP_MAX_SUPPORTED_LANE_COUNTS/INTEL_DP_MAX_SUPPORTED_LANE_CONFIGS
and s/num_common_lane_counts/num_common_lane_configs to make the
difference wrt. max lane counts clearer. (Suraj)
- Add a TODO comment to make the SST fallback logic work the same way as
MST. (Arun)
- Use sort_r()'s default swap function instead of a custom one.
Cc: Suraj Kandpal <suraj.kandpal@intel.com>
Cc: Arun R Murthy <arun.r.murthy@intel.com>
Reviewed-by: Suraj Kandpal <suraj.kandpal@intel.com>
Reviewed-by: Arun R Murthy <arun.r.murthy@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240729144458.2763667-1-imre.deak@intel.com
|
|
Add helpers to set the link mode and BW parameters. These are required
by a follow-up patch setting the parameters for a disabled link.
Reviewed-by: Suraj Kandpal <suraj.kandpal@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240722165503.2084999-9-imre.deak@intel.com
|
|
A follow-up patch will add an alternative way to reduce the link
parameters in BW order on MST links, prepare for that here.
Reviewed-by: Suraj Kandpal <suraj.kandpal@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240722165503.2084999-8-imre.deak@intel.com
|
|
There are multiple failure cases a modeset-retry uevent can be sent for
a link (TBT tunnel BW allocation failure, unrecoverable link training
failure), a follow-up patch adding the handling for a new case where the
DP MST payload allocation fails. The uevent is the same in all cases,
sent to all the connectors on the link, so in case of multiple failures
there is no point in sending a separate uevent for each failure; prevent
this, sending only a single modeset-retry uevent for a commit.
Reviewed-by: Arun R Murthy <arun.r.murthy@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240722165503.2084999-7-imre.deak@intel.com
|
|
Initialize the DP link parameters during HW readout. These need to be
up-to-date at least for the MST topology probing, which depends on the
link rate and lane count programmed in DPCD. A follow-up patch will
program the DPCD values to reflect the maximum link parameters before
the first MST topology probing, but should do so only if the link is
disabled (link_trained==false).
Reviewed-by: Suraj Kandpal <suraj.kandpal@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240722165503.2084999-6-imre.deak@intel.com
|
|
If the DDI encoder output is enabled in HDMI mode there is no point in
calling intel_dp_sync_state(), as in that case the DPCD initialization
will fail - as expected - with AUX timeouts. Prevent calling the hook in
this case.
Reviewed-by: Suraj Kandpal <suraj.kandpal@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240722165503.2084999-5-imre.deak@intel.com
|
|
In the
if (old_ddps != port->ddps || !created)
if (port->ddps && !port->input)
ret = drm_dp_send_enum_path_resources();
sequence the first if's condition is true if the port exists already
(!created) or the port was created anew (hence old_ddps==0) and it was
in the plugged state (port->ddps==1). The second if's condition is true
for output ports in the plugged state. So the function is called for an
output port in the plugged state, regardless if it already existed or
not and regardless of the old plugged state. In all other cases
port->full_pbn can be zeroed as the port is either an input for which
full_pbn is never set, or an output in the unplugged state for which
full_pbn was already zeroed previously or the port was just created
(with port->full_pbn==0).
Simplify the condition, making it clear that the path resources are
always enumerated for an output port in the plugged state.
Cc: Lyude Paul <lyude@redhat.com>
Cc: dri-devel@lists.freedesktop.org
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240722165503.2084999-4-imre.deak@intel.com
|
|
A follow up i915 patch will need to reprobe the MST topology after the
initial probing, add a helper for this.
Cc: Lyude Paul <lyude@redhat.com>
Cc: dri-devel@lists.freedesktop.org
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240722165503.2084999-3-imre.deak@intel.com
|
|
Factor out a function to queue a work for probing the topology, also
used by the next patch.
Cc: Lyude Paul <lyude@redhat.com>
Cc: dri-devel@lists.freedesktop.org
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240722165503.2084999-2-imre.deak@intel.com
|
|
Support "Pre-multiplied" and "None" blend mode on MediaTek's chips by
adding correct blend mode property when the planes init.
Before this patch, only the "Coverage" mode (default) is supported.
For more information, there are three pixel blend modes in DRM driver:
"None", "Pre-multiplied", and "Coverage".
To understand the difference between these modes, let's take a look at
the following two approaches to do alpha blending:
1. Straight:
dst.RGB = src.RGB * src.A + dst.RGB * (1 - src.A)
This is straightforward and easy to understand, when the source layer is
compositing with the destination layer, it's alpha will affect the
result. This is also known as "post-multiplied", or "Coverage" mode.
2. Pre-multiplied:
dst.RGB = src.RGB + dst.RGB * (1 - src.A)
Since the source RGB have already multiplied its alpha, only destination
RGB need to multiply it. This is the "Pre-multiplied" mode in DRM.
For the "None" blend mode in DRM, it means the pixel alpha is ignored
when compositing the layers, only the constant alpha for the composited
layer will take effects.
Reviewed-by: CK Hu <ck.hu@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Hsiao Chien Sung <shawn.sung@mediatek.com>
Link: https://patchwork.kernel.org/project/dri-devel/patch/20240717-alpha-blending-v4-5-4b1c806c0749@mediatek.com/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
|
|
Support "Pre-multiplied" alpha blending mode in Mixer.
Before this patch, only the coverage mode is supported.
To replace the default setting that is set in mtk_ethdr_config(),
we change mtk_ddp_write_mask() to mtk_ddp_write(), and this change will
also reset the NON_PREMULTI_SOURCE bit that was assigned in
mtk_ethdr_config(). Therefore, we must still set NON_PREMULTI_SOURCE bit
if the blend mode is not DRM_MODE_BLEND_PREMULTI.
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Hsiao Chien Sung <shawn.sung@mediatek.com>
Reviewed-by: CK Hu <ck.hu@mediatek.com>
Link: https://patchwork.kernel.org/project/dri-devel/patch/20240717-alpha-blending-v4-4-4b1c806c0749@mediatek.com/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
|
|
Support "Pre-multiplied" alpha blending mode on in OVL.
Before this patch, only the "coverage" mode is supported.
As whether OVL_CON_CLRFMT_MAN bit is enabled, (3 << 12)
means different formats in the datasheet. To prevent
misunderstandings going forward, instead of reusing
OVL_CON_CLRFMT_RGBA8888, we intetionally defined
OVL_CON_CLRFMT_PARGB8888 with bit operation again.
Reviewed-by: CK Hu <ck.hu@mediatek.com>
Signed-off-by: Hsiao Chien Sung <shawn.sung@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://patchwork.kernel.org/project/dri-devel/patch/20240717-alpha-blending-v4-3-4b1c806c0749@mediatek.com/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
|
|
Support "None" alpha blending mode on MediaTek's chips.
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Hsiao Chien Sung <shawn.sung@mediatek.com>
Reviewed-by: CK Hu <ck.hu@mediatek.com>
Link: https://patchwork.kernel.org/project/dri-devel/patch/20240717-alpha-blending-v4-2-4b1c806c0749@mediatek.com/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
|
|
Support "None" alpha blending mode on MediaTek's chips.
Reviewed-by: CK Hu <ck.hu@mediatek.com>
Signed-off-by: Hsiao Chien Sung <shawn.sung@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://patchwork.kernel.org/project/dri-devel/patch/20240717-alpha-blending-v4-1-4b1c806c0749@mediatek.com/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
|
|
The comments do not add any value. Remove.
Reviewed-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240729173320.1053791-1-jani.nikula@intel.com
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
Move and export xe_hw_engine lookup. This is in preparation
to use this in eudebug code where we want to find active
engine.
v2: s/tile/gt due to uapi changes (Mika)
Signed-off-by: Dominik Grzegorzek <dominik.grzegorzek@intel.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Matthew Brost <matthew.brost@intel.com>
Signed-off-by: Matthew Brost <matthew.brost@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240729130152.100130-1-mika.kuoppala@linux.intel.com
|
|
A chain fence is uninitialized if not installed in a drm sync obj. Thus
if xe_sync_entry_cleanup is called and sync->chain_fence is non-NULL the
proper cleanup is dma_fence_chain_free rather than a dma-fence put.
Reported-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Closes: https://gitlab.freedesktop.org/drm/xe/kernel/-/issues/2411
Closes: https://gitlab.freedesktop.org/drm/xe/kernel/-/issues/2261
Fixes: dd08ebf6c352 ("drm/xe: Introduce a new DRM driver for Intel GPUs")
Signed-off-by: Matthew Brost <matthew.brost@intel.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240727012216.2118276-1-matthew.brost@intel.com
|
|
On the off chance that clock value ends up being too high (by means
of skl_ddi_calculate_wrpll() having been called with big enough
value of crtc_state->port_clock * 1000), one possible consequence
may be that the result will not be able to fit into signed int.
Fix this issue by moving conversion of clock parameter from kHz to Hz
into the body of skl_ddi_calculate_wrpll(), as well as casting the
same parameter to u64 type while calculating the value for AFE clock.
This both mitigates the overflow problem and avoids possible erroneous
integer promotion mishaps.
Found by Linux Verification Center (linuxtesting.org) with static
analysis tool SVACE.
Fixes: 82d354370189 ("drm/i915/skl: Implementation of SKL DPLL programming")
Cc: stable@vger.kernel.org
Signed-off-by: Nikita Zhandarovich <n.zhandarovich@fintech.ru>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240729174035.25727-1-n.zhandarovich@fintech.ru
(cherry picked from commit 833cf12846aa19adf9b76bc79c40747726f3c0c1)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
|
|
Fix HDCP2_STREAM_STATUS macro, it called pipe instead of port never
threw a compile error as no one used it.
--v2
-Add Fixes [Jani]
Fixes: d631b984cc90 ("drm/i915/hdcp: Add HDCP 2.2 stream register")
Signed-off-by: Suraj Kandpal <suraj.kandpal@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240730035505.3759899-1-suraj.kandpal@intel.com
(cherry picked from commit 73d7cd542bbd0a7c6881ea0df5255f190a1e7236)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
|
|
On the off chance that clock value ends up being too high (by means
of skl_ddi_calculate_wrpll() having been called with big enough
value of crtc_state->port_clock * 1000), one possible consequence
may be that the result will not be able to fit into signed int.
Fix this issue by moving conversion of clock parameter from kHz to Hz
into the body of skl_ddi_calculate_wrpll(), as well as casting the
same parameter to u64 type while calculating the value for AFE clock.
This both mitigates the overflow problem and avoids possible erroneous
integer promotion mishaps.
Found by Linux Verification Center (linuxtesting.org) with static
analysis tool SVACE.
Fixes: 82d354370189 ("drm/i915/skl: Implementation of SKL DPLL programming")
Cc: stable@vger.kernel.org
Signed-off-by: Nikita Zhandarovich <n.zhandarovich@fintech.ru>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240729174035.25727-1-n.zhandarovich@fintech.ru
|
|
Simplify ast_astdp_read_edid(). Rename register constants. Drop
unnecessary error handling. On success, the helper returns 0; an
error code otherwise.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Jocelyn Falempe <jfalempe@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240717143319.104012-6-tzimmermann@suse.de
|
|
The place for link training is in the encoder's atomic_enable
helper. Remove all related tests from other helper ASTDP functions;
especially ast_astdp_is_connected(), which tests HPD status.
DP link training is controlled by the firmware. A status flag reports
success or failure. The process can be fragile on Aspeed hardware. Moving
the test from connector detection to the atomic_enable allows for several
retries and a longer timeout.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Jocelyn Falempe <jfalempe@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240717143319.104012-5-tzimmermann@suse.de
|
|
The overall control flow of the driver ensures that it never reads
EDID or sets display state on unconnected outputs. Therefore remove
all tests for Hot Plug Detection from these helpers. Also rename
the register constants.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Jocelyn Falempe <jfalempe@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240717143319.104012-4-tzimmermann@suse.de
|
|
Test for running ASTDP firmware during probe. Do not bother testing
this later. We cannot do much anyway if the firmware fails. Do not
initialize the ASTDP conenctor if the test fails during device probing.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reported-by: Shixiong Ou <oushixiong@kylinos.cn>
Tested-by: Shixiong Ou <oushixiong@kylinos.cn>
Reviewed-by: Jocelyn Falempe <jfalempe@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240717143319.104012-3-tzimmermann@suse.de
|
|
Fix HDCP2_STREAM_STATUS macro, it called pipe instead of port never
threw a compile error as no one used it.
--v2
-Add Fixes [Jani]
Fixes: d631b984cc90 ("drm/i915/hdcp: Add HDCP 2.2 stream register")
Signed-off-by: Suraj Kandpal <suraj.kandpal@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240730035505.3759899-1-suraj.kandpal@intel.com
|
|
AS SDP should be computed when VRR timing generator is also enabled.
Correct the compute condition to compute params of Adaptive sync SDP
when VRR timing genrator is enabled along with sink support indication.
--v2:
Modify if condition (Jani).
Fixes: b2013783c445 ("drm/i915/display: Cache adpative sync caps to use it later")
Cc: Mitul Golani <mitulkumar.ajitkumar.golani@intel.com>
Cc: Arun R Murthy <arun.r.murthy@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: intel-gfx@lists.freedesktop.org
Cc: intel-xe@lists.freedesktop.org
Signed-off-by: Mitul Golani <mitulkumar.ajitkumar.golani@intel.com>
Reviewed-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
(added prefix drm in subject)
Link: https://patchwork.freedesktop.org/patch/msgid/20240730040941.396862-1-mitulkumar.ajitkumar.golani@intel.com
|
|
Signed-off-by: Shixiong Ou <oushixiong@kylinos.cn>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20240729065756.123788-1-oushixiong1025@163.com
|
|
Power up the ASTDP connector for connection status detection if the
connector is not active. Keep it powered if a display is attached.
This fixes a bug where the connector does not come back after
disconnecting the display. The encoder's atomic_disable turns off
power on the physical connector. Further HPD reads will fail,
thus preventing the driver from detecting re-connected displays.
For connectors that are actively used, only test the HPD flag without
touching power.
Fixes: f81bb0ac7872 ("drm/ast: report connection status on Display Port.")
Cc: Jocelyn Falempe <jfalempe@redhat.com>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
Cc: Dave Airlie <airlied@redhat.com>
Cc: dri-devel@lists.freedesktop.org
Cc: <stable@vger.kernel.org> # v6.6+
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Jocelyn Falempe <jfalempe@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240717143319.104012-2-tzimmermann@suse.de
|
|
Let's start the new drm-misc-fixes cycle by bringing in 6.11-rc1.
Signed-off-by: Maxime Ripard <mripard@kernel.org>
|
|
Add performance tuning changes for Xe2_HPG
Bspec: 72161
Signed-off-by: Sai Teja Pottumuttu <sai.teja.pottumuttu@intel.com>
Reviewed-by: Gustavo Sousa <gustavo.sousa@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240724121521.2347524-1-sai.teja.pottumuttu@intel.com
|
|
Now that rtp has OR rules, it's not needed to extend it to process OOB
WAs. Previously if an entry had no name, it was considered as "a set of
rules OR'ed with the last named entry".
Instead of generating new entries, add OR rules. The syntax for
xe_wa_oob.rules remains the same, with xe_gen_wa_oob generating the
slightly different table. Object sizes delta are negligible, but having
just one logic makes it easier to maintain:
add/remove: 0/0 grow/shrink: 1/2 up/down: 160/-269 (-109)
Function old new delta
__compound_literal 6104 6264 +160
xe_wa_dump 1839 1810 -29
oob_was 816 576 -240
Total: Before=17257, After=17148, chg -0.63%
Reviewed-by: Gustavo Sousa <gustavo.sousa@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240727015907.899192-9-lucas.demarchi@intel.com
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
|
|
Like commit 512660cd1f1a ("drm/xe/rtp: Expand max rules/actions per
entry") did, expand the maximum number of actions/rules. That commit was
too conservative, just incrementing 2. Other than the ugliness of these
macros and additional preprocessor steps when they are used, there are
no downsides on increasing the maximum: the tables in which they are
used use a sentinel to mark the last element.
With rtp processing now supporting OR rules, it's possible to migrate
the extension made for OOB WAs that "entries with name are OR'ed in
previous entry". For that the maximum number of rules needs to be
increased.
Just double it. Hopefully 12 is sufficient for longer than 6 was.
Reviewed-by: Gustavo Sousa <gustavo.sousa@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240727015907.899192-8-lucas.demarchi@intel.com
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
|
|
Stop doing the calculation both in rtp_mark_active() and in its caller.
The caller easily knows the number of entries to mark, so just pass it
forward. That also simplifies rtp_mark_active() since now it doesn't
have a special case when handling 1 entry.
Reviewed-by: Gustavo Sousa <gustavo.sousa@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240727015907.899192-7-lucas.demarchi@intel.com
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
|
|
The OOB WAs use xe_rtp_process(), without passing an sr to save result
of the actions since there are none. They are also executed in a gt-only
context, making it harder to share the implementation. Thus, introduce a
new set of tests to check these RTP entries. The only check that can be
done is if the entry was marked as active.
Before commit fd6797ec50c5 ("drm/xe/rtp: Fix off-by-one when processing
rules") several of these tests were failing: the processing of OR'ed
entries would make the subsequent entry to be inadvertently enabled.
Reviewed-by: Gustavo Sousa <gustavo.sousa@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240727015907.899192-6-lucas.demarchi@intel.com
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
|
|
Those tests check the behavior of xe_rtp_process_to_sr(), so name them
accordingly to allow adding tests for xe_rtp_process() later.
Reviewed-by: Gustavo Sousa <gustavo.sousa@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240727015907.899192-5-lucas.demarchi@intel.com
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
|
|
Enabling active tracking in the rtp context and check for all the tests
the expected entries become active.
Reviewed-by: Gustavo Sousa <gustavo.sousa@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240727015907.899192-4-lucas.demarchi@intel.com
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
|
|
The RTP tests check both the result of processing the RTP entries and
the outcome saved as SR entries. Rename "count" to be explicit about
what's being counted.
Reviewed-by: Gustavo Sousa <gustavo.sousa@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240727015907.899192-3-lucas.demarchi@intel.com
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
|
|
Add one variant for BMG to make sure the workarounds do not conflict.
This matches the machine with BMG in CI:
BATTLEMAGE e20b:0000 dgfx:1
gfx:Xe2_LPG / Xe2_HPG (20.01)
media:Xe2_LPM / Xe2_HPM (13.01)
display:yes dma_m_s:46 tc:1 gscfi:0 cscfi:1
Stepping = (G:A0, M:A1, D:**, B:**)
Reviewed-by: Gustavo Sousa <gustavo.sousa@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240727015907.899192-2-lucas.demarchi@intel.com
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
|
|
Although all current Xe2 platforms support FlatCCS, we probably
shouldn't assume that will be universally true forever. In the past
we've had platforms like PVC that didn't support compression, and the
same could show up again at some point in the future. Future-proof the
migration code by adding an explicit check for FlatCCS support to the
condition that decides whether to use a compressed PAT index for
migration.
While we're at it, we can drop the IS_DGFX check since it's redundant
with the src_is_vram check (only dGPUs have VRAM).
Cc: Akshata Jahagirdar <akshata.jahagirdar@intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Akshata Jahagirdar <akshata.jahagirdar@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240726171757.2728819-2-matthew.d.roper@intel.com
|
|
Being part o the display, ideally the setup and cleanup would be done by
display itself. However this is a bigger refactor that needs to be done
on both i915 and xe. For now, just fix the leak:
unreferenced object 0xffff8881a0300008 (size 192):
comm "modprobe", pid 4354, jiffies 4295647021
hex dump (first 32 bytes):
00 00 87 27 81 88 ff ff 18 80 9b 00 00 c9 ff ff ...'............
18 81 9b 00 00 c9 ff ff 00 00 00 00 00 00 00 00 ................
backtrace (crc 99260e31):
[<ffffffff823ce65b>] kmemleak_alloc+0x4b/0x80
[<ffffffff81493be2>] kmalloc_trace_noprof+0x312/0x3d0
[<ffffffffa1345679>] intel_opregion_setup+0x89/0x700 [xe]
[<ffffffffa125bfaf>] xe_display_init_noirq+0x2f/0x90 [xe]
[<ffffffffa1199ec3>] xe_device_probe+0x7a3/0xbf0 [xe]
[<ffffffffa11f3713>] xe_pci_probe+0x333/0x5b0 [xe]
[<ffffffff81af6be8>] local_pci_probe+0x48/0xb0
[<ffffffff81af8778>] pci_device_probe+0xc8/0x280
[<ffffffff81d09048>] really_probe+0xf8/0x390
[<ffffffff81d0937a>] __driver_probe_device+0x8a/0x170
[<ffffffff81d09503>] driver_probe_device+0x23/0xb0
[<ffffffff81d097b7>] __driver_attach+0xc7/0x190
[<ffffffff81d0628d>] bus_for_each_dev+0x7d/0xd0
[<ffffffff81d0851e>] driver_attach+0x1e/0x30
[<ffffffff81d07ac7>] bus_add_driver+0x117/0x250
Fixes: 44e694958b95 ("drm/xe/display: Implement display support")
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240724215309.644423-1-lucas.demarchi@intel.com
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
|
|
Fix build with CONFIG_NOUVEAU_PLATFORM_DRIVER enabled:
../drivers/gpu/drm/nouveau/nouveau_platform.c: In function ‘nouveau_platform_probe’:
../drivers/gpu/drm/nouveau/nouveau_platform.c:29:13: error: unused variable ‘ret’ [-Werror=unused-variable]
29 | int ret;
| ^~~
Fixes: 961ae5f9807b ("drm/nouveau: handle pci/tegra drm_dev_{alloc, register} from common code")
Cc: Ben Skeggs <bskeggs@nvidia.com>
Cc: Danilo Krummrich <dakr@kernel.org>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Danilo Krummrich <dakr@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240729123624.868907-1-jani.nikula@intel.com
|
|
PWR_CLK_STATE only needs to be modified up until gen11. For gen12 this
code is not applicable. Remove code to update context image with
PWR_CLK_STATE for gen12.
Fixes: 00a7f0d7155c ("drm/i915/tgl: Add perf support on TGL")
Signed-off-by: Umesh Nerlige Ramappa <umesh.nerlige.ramappa@intel.com>
Reviewed-by: Ashutosh Dixit <ashutosh.dixit@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240629005643.3050678-1-umesh.nerlige.ramappa@intel.com
(cherry picked from commit 7b5bdae7740eb6a3d09f9cd4e4b07362a15b86b3)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
|
|
Backmerging to get a late RC of v6.10 before moving into v6.11.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
|
|
I2C v7, SMBus 3.2, and I3C 1.1.1 specifications have replaced "master/slave"
with more appropriate terms. Inspired by Wolfram's series to fix drivers/i2c/,
fix the terminology for users of I2C_ALGOBIT bitbanging interface, now that
the approved verbiage exists in the specification.
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Easwar Hariharan <eahariha@linux.microsoft.com>
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20240711052734.1273652-3-eahariha@linux.microsoft.com
|
|
This function accidentally returns zero/success on the failure path.
It leads to locking issues and an uninitialized *map_copy in the
caller.
Fixes: b4b0193e83cb ("drm/fbdev-generic: Fix locking with drm_client_buffer_vmap_local()")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Dmitry Osipenko <dmitry.osipenko@collabora.com>
Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/89d13df3-747c-4c5d-b122-d081aef5110a@stanley.mountain
|
|
We only had a couple of array[] declarations, and changing them to just
use 'MAX()' instead of 'max()' fixes the issue.
This will allow us to simplify our min/max macros enormously, since they
can now unconditionally use temporary variables to avoid using the
argument values multiple times.
Cc: David Laight <David.Laight@aculab.com>
Cc: Lorenzo Stoakes <lorenzo.stoakes@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This just standardizes the use of MIN() and MAX() macros, with the very
traditional semantics. The goal is to use these for C constant
expressions and for top-level / static initializers, and so be able to
simplify the min()/max() macros.
These macro names were used by various kernel code - they are very
traditional, after all - and all such users have been fixed up, with a
few different approaches:
- trivial duplicated macro definitions have been removed
Note that 'trivial' here means that it's obviously kernel code that
already included all the major kernel headers, and thus gets the new
generic MIN/MAX macros automatically.
- non-trivial duplicated macro definitions are guarded with #ifndef
This is the "yes, they define their own versions, but no, the include
situation is not entirely obvious, and maybe they don't get the
generic version automatically" case.
- strange use case #1
A couple of drivers decided that the way they want to describe their
versioning is with
#define MAJ 1
#define MIN 2
#define DRV_VERSION __stringify(MAJ) "." __stringify(MIN)
which adds zero value and I just did my Alexander the Great
impersonation, and rewrote that pointless Gordian knot as
#define DRV_VERSION "1.2"
instead.
- strange use case #2
A couple of drivers thought that it's a good idea to have a random
'MIN' or 'MAX' define for a value or index into a table, rather than
the traditional macro that takes arguments.
These values were re-written as C enum's instead. The new
function-line macros only expand when followed by an open
parenthesis, and thus don't clash with enum use.
Happily, there weren't really all that many of these cases, and a lot of
users already had the pattern of using '#ifndef' guarding (or in one
case just using '#undef MIN') before defining their own private version
that does the same thing. I left such cases alone.
Cc: David Laight <David.Laight@aculab.com>
Cc: Lorenzo Stoakes <lorenzo.stoakes@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Commit 3a7e02c040b1 ("minmax: avoid overly complicated constant
expressions in VM code") added the simpler MIN_T/MAX_T macros in order
to avoid some excessive expansion from the rather complicated regular
min/max macros.
The complexity of those macros stems from two issues:
(a) trying to use them in situations that require a C constant
expression (in static initializers and for array sizes)
(b) the type sanity checking
and MIN_T/MAX_T avoids both of these issues.
Now, in the whole (long) discussion about all this, it was pointed out
that the whole type sanity checking is entirely unnecessary for
min_t/max_t which get a fixed type that the comparison is done in.
But that still leaves min_t/max_t unnecessarily complicated due to
worries about the C constant expression case.
However, it turns out that there really aren't very many cases that use
min_t/max_t for this, and we can just force-convert those.
This does exactly that.
Which in turn will then allow for much simpler implementations of
min_t()/max_t(). All the usual "macros in all upper case will evaluate
the arguments multiple times" rules apply.
We should do all the same things for the regular min/max() vs MIN/MAX()
cases, but that has the added complexity of various drivers defining
their own local versions of MIN/MAX, so that needs another level of
fixes first.
Link: https://lore.kernel.org/all/b47fad1d0cf8449886ad148f8c013dae@AcuMS.aculab.com/
Cc: David Laight <David.Laight@aculab.com>
Cc: Lorenzo Stoakes <lorenzo.stoakes@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
