| Age | Commit message (Collapse) | Author |
|---|
|
rss_ctx.test_rss_key_indir implicitly expects at least 5 queues,
as it checks that the traffic on first 2 queues is lower than
the remaining queues when we use all queues. Special case fewer
queues.
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250901173139.881070-2-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The rss_ctx test has gotten pretty flaky after I increased
the queue count in NIPA 2->3. Not 100% clear why. We get
a lot of failures in the rss_ctx.test_hitless_key_update case.
Looking closer it appears that the failures are mostly due
to startup costs. I measured the following timing for ethtool -X:
- python cmd(shell=True) : 150-250msec
- python cmd(shell=False) : 50- 70msec
- timed in bash : 45- 55msec
- YNL Netlink call : 2- 4msec
- .set_rxfh callback : 1- 2msec
The target in the test was set to 200msec. We were mostly measuring
ethtool startup cost it seems. Switch to YNL since it's 100x faster.
Lower the pass criteria to 150msec, no real science behind this number
but we removed some overhead, drivers which previously passed 200msec
should easily pass 150msec now.
Separately we should probably follow up on defaulting to shell=False,
when script doesn't explicitly ask for True, because the overhead
is rather significant.
Switch from _rss_key_rand() to random.randbytes(), YNL takes a binary
array rather than array of ints.
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250901173139.881070-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Correct the Mode Control Register (MODCTRL) offset for RZ/N MIIC.
According to the R-IN Engine and Ethernet Peripherals Manual (Rev.1.30)
[0], Table 10.1 "Ethernet Accessory Register List", MODCTRL is at offset
0x8, not 0x20 as previously defined.
Offset 0x20 actually maps to the Port Trigger Control Register (PTCTRL),
which controls PTP_MODE[3:0] and RGMII_CLKSEL[4]. Using this incorrect
definition prevented the driver from configuring the SW_MODE[4:0] bits
in MODCTRL, which control the internal connection of Ethernet ports. As
a result, the MIIC could not be switched into the correct mode, leading
to link setup failures and non-functional Ethernet ports on affected
systems.
[0] https://www.renesas.com/en/document/mah/rzn1d-group-rzn1s-group-rzn1l-group-users-manual-r-engine-and-ethernet-peripherals?r=1054571
Fixes: 7dc54d3b8d91 ("net: pcs: add Renesas MII converter driver")
Cc: stable@kernel.org
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://patch.msgid.link/20250901112019.16278-1-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
same story as with do_new_mount_fc().
Reviewed-by: Christian Brauner <brauner@kernel.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
do_add_mount() consumes vfsmount on success; just follow it with
conditional retain_and_null_ptr() on success and we can switch
to __free() for mnt and be done with that - unlock_mount() is
in the very end.
Reviewed-by: Christian Brauner <brauner@kernel.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
finish_automount() can't use lock_mount() - it treats finding something
already mounted as "quitely drop our mount and return 0", not as
"mount on top of whatever mounted there". It's been open-coded;
let's take it into a helper similar to lock_mount(). "something's
already mounted" => -EBUSY, finish_automount() needs to distinguish
it from the normal case and it can't happen in other failure cases.
Reviewed-by: Christian Brauner <brauner@kernel.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
preparations for making unlock_mount() a __cleanup();
can't have path_put() inside mount_lock scope.
Reviewed-by: Christian Brauner <brauner@kernel.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
preparations for making unlock_mount() a __cleanup();
can't have path_put() inside mount_lock scope.
Reviewed-by: Christian Brauner <brauner@kernel.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
It's enough to check that dentries match; if path->dentry is equal to
m->mnt_root, superblocks will match as well.
Reviewed-by: Christian Brauner <brauner@kernel.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
We want to mount beneath the given location. For that operation to
make sense, location must be the root of some mount that has something
under it. Currently we let it proceed if those requirements are not met,
with rather meaningless results, and have that bogosity caught further
down the road; let's fail early instead - do_lock_mount() doesn't make
sense unless those conditions hold, and checking them there makes
things simpler.
Reviewed-by: Christian Brauner <brauner@kernel.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
1) checking that location we want to move does point to root of some mount
can be done before anything else; that property is not going to change
and having it already verified simplifies the analysis.
2) checking the type agreement between what we are trying to move and what
we are trying to move it onto also belongs in the very beginning -
do_lock_mount() might end up switching new_path to something that overmounts
the original location, but... the same type agreement applies to overmounts,
so we could just as well check against the original location.
3) since we know that old_path->dentry is the root of old_path->mnt, there's
no point bothering with path_is_overmounted() in can_move_mount_beneath();
it's simply a check for the mount we are trying to move having non-NULL
->overmount. And with that, we can switch can_move_mount_beneath() to
taking old instead of old_path, leaving no uses of old_path past the original
checks.
Reviewed-by: Christian Brauner <brauner@kernel.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
Both 'parent' and 'ns' are used at most once, no point precalculating those...
Reviewed-by: Christian Brauner <brauner@kernel.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
Prior to the call of do_new_mount_fc() the caller has just done successful
vfs_get_tree(). Then do_new_mount_fc() does several checks on resulting
superblock, and either does fc_drop_locked() and returns an error or
proceeds to unlock the superblock and call vfs_create_mount().
The thing is, there's no reason to delay that unlock + vfs_create_mount() -
the tests do not rely upon the state of ->s_umount and
fc_drop_locked()
put_fs_context()
is equivalent to
unlock ->s_umount
put_fs_context()
Doing vfs_create_mount() before the checks allows us to move vfs_get_tree()
from caller to do_new_mount_fc() and collapse it with vfs_create_mount()
into an fc_mount() call.
Reviewed-by: Christian Brauner <brauner@kernel.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
here a use of __free(path_put) for dropping fs_root is enough to
make guard(mount_locked_reader) fit...
Reviewed-by: Christian Brauner <brauner@kernel.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
All we need here is to follow ->overmount on root mount of namespace...
Reviewed-by: Christian Brauner <brauner@kernel.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
... and document that locking requirements for is_path_reachable().
There is one questionable caller in do_listmount() where we are not
holding mount_lock *and* might not have the first argument mounted.
However, in that case it will immediately return true without having
to look at the ancestors. Might be cleaner to move the check into
non-LSTM_ROOT case which it really belongs in - there the check is
not always true and is_mounted() is guaranteed.
Document the locking environments for is_path_reachable() callers:
get_peer_under_root()
get_dominating_id()
do_statmount()
do_listmount()
Reviewed-by: Christian Brauner <brauner@kernel.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
The reason why it needs only mount_locked_reader is that there's no lockless
accesses of expiry lists.
Reviewed-by: Christian Brauner <brauner@kernel.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
... and document the locking requirements of __has_locked_children()
Reviewed-by: Christian Brauner <brauner@kernel.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
Reviewed-by: Christian Brauner <brauner@kernel.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
Currently we are taking mount_writer; what that function needs is
either mount_locked_reader (we are not changing anything, we just
want to iterate through the subtree) or namespace_shared and
a reference held by caller on the root of subtree - that's also
enough to stabilize the topology.
The thing is, all callers are already holding at least namespace_shared
as well as a reference to the root of subtree.
Let's make the callers provide locking warranties - don't mess with
mount_lock in check_for_nsfs_mounts() itself and document the locking
requirements.
Reviewed-by: Christian Brauner <brauner@kernel.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
clean fit; namespace_shared due to iterating through ns->mounts.
Reviewed-by: Christian Brauner <brauner@kernel.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
clean fit; guards can't be weaker due to umount_tree() call.
Setting emptied_ns requires namespace_excl, but not anything
mount_lock-related.
Reviewed-by: Christian Brauner <brauner@kernel.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
Clean fit; guards can't be weaker due to umount_tree() calls.
Reviewed-by: Christian Brauner <brauner@kernel.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
clean fit; namespace_excl to modify propagation graph
Reviewed-by: Christian Brauner <brauner@kernel.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
clean fit; namespace_excl to modify propagation graph
Reviewed-by: Christian Brauner <brauner@kernel.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
clean fit; namespace_shared due to iterating through ns->mounts.
Reviewed-by: Christian Brauner <brauner@kernel.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
Clean fit for guards use; guards can't be weaker due to umount_tree() calls.
Reviewed-by: Christian Brauner <brauner@kernel.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
Note that just as path_put, it should never be done in scope of
namespace_sem, be it shared or exclusive.
Reviewed-by: Christian Brauner <brauner@kernel.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
mount_writer: write_seqlock; that's an equivalent of {un,}lock_mount_hash()
mount_locked_reader: read_seqlock_excl; these tend to be open-coded.
No bulk conversions, please - if nothing else, quite a few places take
use mount_writer form when mount_locked_reader is sufficent. It needs
to be dealt with carefully.
Reviewed-by: Christian Brauner <brauner@kernel.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
If anything, namespace_lock should be DEFINE_LOCK_GUARD_0, not DEFINE_GUARD.
That way we
* do not need to feed it a bogus argument
* do not get gcc trying to compare an address of static in
file variable with -4097 - and, if we are unlucky, trying to keep
it in a register, with spills and all such.
The same problems apply to grabbing namespace_sem shared.
Rename it to namespace_excl, add namespace_shared, convert the existing users:
guard(namespace_lock, &namespace_sem) => guard(namespace_excl)()
guard(rwsem_read, &namespace_sem) => guard(namespace_shared)()
scoped_guard(namespace_lock, &namespace_sem) => scoped_guard(namespace_excl)
scoped_guard(rwsem_read, &namespace_sem) => scoped_guard(namespace_shared)
Reviewed-by: Christian Brauner <brauner@kernel.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
While tracking down a problem where constant expressions used by
BUILD_BUG_ON() suddenly stopped working[1], we found that an added static
initializer was convincing the compiler that it couldn't track the state
of the prior statically initialized value. Tracing this down found that
ffs() was used in the initializer macro, but since it wasn't marked with
__attribute__const__, the compiler had to assume the function might
change variable states as a side-effect (which is not true for ffs(),
which provides deterministic math results).
For arc architecture with CONFIG_ISA_ARCV2=y, the __fls() function
uses __builtin_arc_fls() which lacks GCC's const attribute, preventing
compile-time constant folding, and KUnit testing of ffs/fls fails on
arc[3]. A patch[2] to GCC to solve this has been sent.
Add a fix for this by handling compile-time constants with the standard
__builtin_clzl() builtin (which has const attribute) while preserving
the optimized arc-specific builtin for runtime cases. This has the added
benefit of skipping runtime calculation of compile-time constant values.
Even with the GCC bug fixed (which is about "attribute const") this is a
good change to avoid needless runtime costs, and should be done
regardless of the state of GCC's bug.
Build tested ARCH=arc allyesconfig with GCC arc-linux 15.2.0.
Link: https://github.com/KSPP/linux/issues/364 [1]
Link: https://gcc.gnu.org/pipermail/gcc-patches/2025-August/693273.html
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202508031025.doWxtzzc-lkp@intel.com/ [3]
Signed-off-by: Kees Cook <kees@kernel.org>
Acked-by: Vineet Gupta <vgupta@kernel.org>
Signed-off-by: Yury Norov (NVIDIA) <yury.norov@gmail.com>
|
|
When sending llc packets with vlan tx offload, the hardware fails to
actually add the tag. Deal with this by fixing it up in software.
Fixes: 656e705243fd ("net-next: mediatek: add support for MT7623 ethernet")
Reported-by: Thibaut VARENE <hacks@slashdirt.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250831182007.51619-1-nbd@nbd.name
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Russell King says:
====================
net: fix optical SFP failures
A regression was reported back in April concerning pcs-lynx and 10G
optical SFPs. This patch series addresses that regression, and likely
similar unreported regressions.
These patches:
- Add phy_interface_weight() which will be used in the solution.
- Split out the code that determines the inband "type" for an
interface mode.
- Clear the Autoneg bit in the advertising mask, or the Autoneg bit
in the support mask and the entire advertising mask if the selected
interface mode has no inband capabilties.
Tested with the mvpp2 patch posted earlier today.
====================
Link: https://patch.msgid.link/aLSHmddAqiCISeK3@shell.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Mathew reports that as a result of commit 6561f0e547be ("net: pcs:
pcs-lynx: implement pcs_inband_caps() method"), 10G SFP modules no
longer work with the Lynx PCS.
This problem is not specific to the Lynx PCS, but is caused by commit
df874f9e52c3 ("net: phylink: add pcs_inband_caps() method") which added
validation of the autoneg state to the optical SFP configuration path.
Fix this by handling interface modes that fundamentally have no
inband negotiation more correctly - if we only have a single interface
mode, clear the Autoneg support bit and the advertising mask. If the
module can operate with several different interface modes, autoneg may
be supported for other modes, so leave the support mask alone and just
clear the Autoneg bit in the advertising mask.
This restores 10G optical module functionality with PCS that supply
their inband support, and makes ethtool output look sane.
Reported-by: Mathew McBride <matt@traverse.com.au>
Closes: https://lore.kernel.org/r/025c0ebe-5537-4fa3-b05a-8b835e5ad317@app.fastmail.com
Fixes: df874f9e52c3 ("net: phylink: add pcs_inband_caps() method")
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://patch.msgid.link/E1uslwx-00000001SPB-2kiM@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Provide a function to get the type of the inband signalling used for
a PHY interface type. This will be used in the subsequent patch to
address problems with 10G optical modules.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/E1uslws-00000001SP5-1R2R@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/E1uslwn-00000001SOx-0a7H@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Overhead of using shell=True is quite significant.
Micro-benchmark of running ethtool --help shows that
non-shell run is 2x faster.
Runtime of the XDP tests also shows improvement:
this patch: 2m34s 2m21s 2m18s 2m18s
before: 2m54s 2m36s 2m34s
Reviewed-by: Breno Leitao <leitao@debian.org>
Link: https://patch.msgid.link/20250830184317.696121-2-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Clean up tests which expect shell=True without explicitly passing
that param to cmd(). There seems to be only one such case, and
in fact it's better converted to a direct write.
Reviewed-by: Breno Leitao <leitao@debian.org>
Link: https://patch.msgid.link/20250830184317.696121-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When tcp_ao_copy_all_matching() fails in tcp_v6_syn_recv_sock() it just
exits the function. This ends up causing a memory-leak:
unreferenced object 0xffff0000281a8200 (size 2496):
comm "softirq", pid 0, jiffies 4295174684
hex dump (first 32 bytes):
7f 00 00 06 7f 00 00 06 00 00 00 00 cb a8 88 13 ................
0a 00 03 61 00 00 00 00 00 00 00 00 00 00 00 00 ...a............
backtrace (crc 5ebdbe15):
kmemleak_alloc+0x44/0xe0
kmem_cache_alloc_noprof+0x248/0x470
sk_prot_alloc+0x48/0x120
sk_clone_lock+0x38/0x3b0
inet_csk_clone_lock+0x34/0x150
tcp_create_openreq_child+0x3c/0x4a8
tcp_v6_syn_recv_sock+0x1c0/0x620
tcp_check_req+0x588/0x790
tcp_v6_rcv+0x5d0/0xc18
ip6_protocol_deliver_rcu+0x2d8/0x4c0
ip6_input_finish+0x74/0x148
ip6_input+0x50/0x118
ip6_sublist_rcv+0x2fc/0x3b0
ipv6_list_rcv+0x114/0x170
__netif_receive_skb_list_core+0x16c/0x200
netif_receive_skb_list_internal+0x1f0/0x2d0
This is because in tcp_v6_syn_recv_sock (and the IPv4 counterpart), when
exiting upon error, inet_csk_prepare_forced_close() and tcp_done() need
to be called. They make sure the newsk will end up being correctly
free'd.
tcp_v4_syn_recv_sock() makes this very clear by having the put_and_exit
label that takes care of things. So, this patch here makes sure
tcp_v4_syn_recv_sock and tcp_v6_syn_recv_sock have similar
error-handling and thus fixes the leak for TCP-AO.
Fixes: 06b22ef29591 ("net/tcp: Wire TCP-AO to request sockets")
Signed-off-by: Christoph Paasch <cpaasch@openai.com>
Reviewed-by: Dmitry Safonov <0x7f454c46@gmail.com>
Link: https://patch.msgid.link/20250830-tcpao_leak-v1-1-e5878c2c3173@openai.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
tcfa_qstats is currently only used to hold drops and overlimits counters.
tcf_action_inc_drop_qstats() and tcf_action_inc_overlimit_qstats()
currently acquire a->tcfa_lock to increment these counters.
Switch to two atomic_t to get lock-free accounting.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Jamal Hadi Salim <jhs@mojatatu.com>
Link: https://patch.msgid.link/20250901093141.2093176-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Jamal reported that we had to use BH safety after all,
because stats can be updated from BH handler.
Fixes: 3133d5c15cb5 ("net_sched: remove BH blocking in eight actions")
Fixes: 53df77e78590 ("net_sched: act_skbmod: use RCU in tcf_skbmod_dump()")
Fixes: e97ae742972f ("net_sched: act_tunnel_key: use RCU in tunnel_key_dump()")
Fixes: 48b5e5dbdb23 ("net_sched: act_vlan: use RCU in tcf_vlan_dump()")
Reported-by: Jamal Hadi Salim <jhs@mojatatu.com>
Closes: https://lore.kernel.org/netdev/CAM0EoMmhq66EtVqDEuNik8MVFZqkgxFbMu=fJtbNoYD7YXg4bA@mail.gmail.com/
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Jamal Hadi Salim <jhs@mojatatu.com>
Link: https://patch.msgid.link/20250901092608.2032473-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This patch improves the utils.py module by removing unused imports
(errno, random), simplifying the fd_read_timeout() function by
eliminating unnecessary else clause, and cleaning up code style in the
defer class constructor.
Additionally, it renames the parameter in rand_port() from 'type' to
'stype' to avoid shadowing the built-in Python name 'type', improving
code clarity and preventing potential issues.
These changes enhance code readability and maintainability without
affecting functionality.
Signed-off-by: Breno Leitao <leitao@debian.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250901-fix-v1-1-df0abb67481e@debian.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Fix sparse warnings about endianness. Store DMA addr to a variable
of correct type and then only convert it when writing to the descriptor.
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250901210818.1025316-2-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This reverts commit 8401a108a63302a5a198c7075d857895ca624851.
I got a report from an (anonymous) Sundance user:
Ethernet controller: Sundance Technology Inc / IC Plus Corp IC Plus IP100A Integrated 10/100 Ethernet MAC + PHY (rev 31)
Revert the driver back in. Make following changes:
- update Denis's email address in MAINTAINERS
- adjust to timer API renames:
- del_timer_sync() -> timer_delete_sync()
- from_timer() -> timer_container_of()
Fixes: 8401a108a633 ("eth: remove the DLink/Sundance (ST201) driver")
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250901210818.1025316-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
During GTK rekey, mac80211 issues a clear key (if the old key exists)
followed by an install key operation in the same context. This causes
ath11k to send two WMI commands in quick succession: one to clear the
old key and another to install the new key in the same slot.
Under certain conditions—especially under high load or time sensitive
scenarios, firmware may process these commands asynchronously in a way
that firmware assumes the key is cleared whereas hardware has a valid key.
This inconsistency between hardware and firmware leads to group addressed
packet drops. Only setting the same key again can restore a valid key in
firmware and allow packets to be transmitted.
This issue remained latent because the host's clear key commands were
not effective in firmware until commit 436a4e886598 ("ath11k: clear the
keys properly via DISABLE_KEY"). That commit enabled the host to
explicitly clear group keys, which inadvertently exposed the race.
To mitigate this, restrict group key clearing across all modes (AP, STA,
MESH). During rekey, the new key can simply be set on top of the previous
one, avoiding the need for a clear followed by a set.
However, in AP mode specifically, permit group key clearing when no
stations are associated. This exception supports transitions from secure
modes (e.g., WPA2/WPA3) to open mode, during which all associated peers
are removed and the group key is cleared as part of the transition.
Add a per-BSS station counter to track the presence of stations during
set key operations. Also add a reset_group_keys flag to track the key
re-installation state and avoid repeated installation of the same key
when the number of connected stations transitions to non-zero within a
rekey period.
Additionally, for AP and Mesh modes, when the first station associates,
reinstall the same group key that was last set. This ensures that the
firmware recovers from any race that may have occurred during a previous
key clear when no stations were associated.
This change ensures that key clearing is permitted only when no clients
are connected, avoiding packet loss while enabling dynamic security mode
transitions.
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.9.0.1-02146-QCAHKSWPL_SILICONZ-1
Tested-on: WCN6855 hw2.1 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.41
Reported-by: Steffen Moser <lists@steffen-moser.de>
Closes: https://lore.kernel.org/linux-wireless/c6366409-9928-4dd7-bf7b-ba7fcf20eabf@steffen-moser.de
Fixes: 436a4e886598 ("ath11k: clear the keys properly via DISABLE_KEY")
Signed-off-by: Rameshkumar Sundaram <rameshkumar.sundaram@oss.qualcomm.com>
Tested-by: Nicolas Escande <nico.escande@gmail.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250810170018.1124014-1-rameshkumar.sundaram@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
Currently, when updating EMLSR capabilities of a multi-link (ML) station,
only the EMLSR parameters (e.g., padding delay, transition delay, and
timeout) are sent to firmware. However, firmware also requires the
EMLSR support flag to be set in the MLO flags of the peer assoc WMI
command to properly handle EML operating mode notification frames.
Set the ATH12K_WMI_FLAG_MLO_EMLSR_SUPPORT flag in the peer assoc WMI
command when the ML station is EMLSR-capable, so that the firmware can
respond to EHT EML action frames from associated stations.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Fixes: 4bcf9525bc49 ("wifi: ath12k: update EMLSR capabilities of ML Station")
Signed-off-by: Ramya Gnanasekar <ramya.gnanasekar@oss.qualcomm.com>
Signed-off-by: Rameshkumar Sundaram <rameshkumar.sundaram@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250801104920.3326352-1-rameshkumar.sundaram@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
In get_bpf_prog_info_linear two calls to bpf_obj_get_info_by_fd are
made, the first to compute memory requirements for a struct perf_bpil
and the second to fill it in. Previously the code would warn when the
second call didn't match the first. Such races can be common place in
things like perf test, whose perf trace tests will frequently load BPF
programs. Rather than a debug message, return actual errors for this
case. Out of paranoia also validate the read bpf_prog_info array
value. Change the type of ptr to avoid mismatched pointer type
compiler warnings. Add some additional debug print outs and sanity
asserts.
Closes: https://lore.kernel.org/lkml/CAP-5=fWJQcmUOP7MuCA2ihKnDAHUCOBLkQFEkQES-1ZZTrgf8Q@mail.gmail.com/
Fixes: 6ac22d036f86 ("perf bpf: Pull in bpf_program__get_prog_info_linear()")
Reviewed-by: Namhyung Kim <namhyung@kernel.org>
Signed-off-by: Ian Rogers <irogers@google.com>
Link: https://lore.kernel.org/r/20250902181713.309797-4-irogers@google.com
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
|
|
The array's contents is a compile time constant. Constify to make the
code more intention revealing and avoid unintended errors.
Reviewed-by: Namhyung Kim <namhyung@kernel.org>
Signed-off-by: Ian Rogers <irogers@google.com>
Link: https://lore.kernel.org/r/20250902181713.309797-3-irogers@google.com
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
|
|
Calls to perf_env__insert_bpf_prog_info may fail as a sideband thread
may already have inserted the bpf_prog_info. Such failures may yield
info_linear being freed which then causes use-after-free issues with
the internal bpf_prog_info info struct. Make it so that
perf_env__insert_bpf_prog_info trigger early non-error paths and fix
the use-after-free in perf_event__synthesize_one_bpf_prog. Add proper
return error handling to perf_env__add_bpf_info (that calls
perf_env__insert_bpf_prog_info) and propagate the return value in its
callers.
Closes: https://lore.kernel.org/lkml/CAP-5=fWJQcmUOP7MuCA2ihKnDAHUCOBLkQFEkQES-1ZZTrgf8Q@mail.gmail.com/
Fixes: 03edb7020bb9 ("perf bpf: Fix two memory leakages when calling perf_env__insert_bpf_prog_info()")
Reviewed-by: Namhyung Kim <namhyung@kernel.org>
Signed-off-by: Ian Rogers <irogers@google.com>
Link: https://lore.kernel.org/r/20250902181713.309797-2-irogers@google.com
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
|
|
Remove deadcode since CXL no longer calls hmat_update_target_coordinates().
Reviewed-by: Jonathan Cameron <jonathan.cameron@huawei.com>
Link: https://patch.msgid.link/20250829222907.1290912-5-dave.jiang@intel.com
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
|
