| Age | Commit message (Collapse) | Author |
|---|
|
Some devices support both symmetric (same value for all PFs) and
asymmetric, while others only support symmetric configuration. This
implementation prefers asymmetric, since it is closer to the devlink
model (per function settings), but falls back to symmetric when needed.
Example usage:
devlink dev param set pci/0000:01:00.0 name total_vfs value <u16> cmode permanent
devlink dev reload pci/0000:01:00.0 action fw_activate
echo 1 >/sys/bus/pci/devices/0000:01:00.0/remove
echo 1 >/sys/bus/pci/rescan
cat /sys/bus/pci/devices/0000:01:00.0/sriov_totalvfs
Signed-off-by: Vlad Dumitrescu <vdumitrescu@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Tested-by: Kamal Heib <kheib@redhat.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250907012953.301746-5-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Example usage:
devlink dev param set pci/0000:01:00.0 name enable_sriov value {true, false} cmode permanent
devlink dev reload pci/0000:01:00.0 action fw_activate
echo 1 >/sys/bus/pci/devices/0000:01:00.0/remove
echo 1 >/sys/bus/pci/rescan
grep ^ /sys/bus/pci/devices/0000:01:00.0/sriov_*
Signed-off-by: Vlad Dumitrescu <vdumitrescu@nvidia.com>
Tested-by: Kamal Heib <kheib@redhat.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250907012953.301746-4-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Selects which algorithm should be used by the NIC in order to decide rate of
CQE compression dependeng on PCIe bus conditions.
Supported values:
1) balanced, merges fewer CQEs, resulting in a moderate compression ratio
but maintaining a balance between bandwidth savings and performance
2) aggressive, merges more CQEs into a single entry, achieving a higher
compression rate and maximizing performance, particularly under high
traffic loads.
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250907012953.301746-3-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
NICs are typically configured with total_vfs=0, forcing users to rely
on external tools to enable SR-IOV (a widely used and essential feature).
Add total_vfs parameter to devlink for SR-IOV max VF configurability.
Enables standard kernel tools to manage SR-IOV, addressing the need for
flexible VF configuration.
Signed-off-by: Vlad Dumitrescu <vdumitrescu@nvidia.com>
Tested-by: Kamal Heib <kheib@redhat.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250907012953.301746-2-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Change the 'ret' variable in lpfc_sli4_issue_wqe() from uint32_t to int,
as it needs to store either negative error codes or zero returned by
lpfc_sli4_wq_put().
Storing the negative error codes in unsigned type, doesn't cause an
issue at runtime but can be confusing. Additionally, assigning negative
error codes to unsigned type may trigger a GCC warning when the
-Wsign-conversion flag is enabled.
No effect on runtime.
Signed-off-by: Qianfeng Rong <rongqianfeng@vivo.com>
Reviewed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Change the 'ret' variable in iscsit_tmr_task_reassign() from u64 to int,
as it needs to store either negative value or zero returned by
iscsit_find_cmd_for_recovery().
Storing the negative error codes in unsigned type, or performing equality
comparisons (e.g., ret == -2), doesn't cause an issue at runtime [1] but
can be confusing. Additionally, assigning negative error codes to
unsigned type may trigger a GCC warning when the -Wsign-conversion flag
is enabled.
No effect on runtime.
Link: https://lore.kernel.org/all/x3wogjf6vgpkisdhg3abzrx7v7zktmdnfmqeih5kosszmagqfs@oh3qxrgzkikf/ #1
Signed-off-by: Qianfeng Rong <rongqianfeng@vivo.com>
Reviewed-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Matthieu Baerts says:
====================
mptcp: make ADD_ADDR retransmission timeout adaptive
Currently, the MPTCP ADD_ADDR notifications are retransmitted after a
fixed timeout controlled by the net.mptcp.add_addr_timeout sysctl knob,
if the corresponding "echo" packets are not received before. This can be
too slow (or too quick), especially with a too cautious default value
set to 2 minutes.
- Patch 1: make ADD_ADDR retransmission timeout adaptive, using the
TCP's retransmission timeout. The corresponding sysctl knob is now
used as a maximum value.
- Patch 2: now that these ADD_ADDR retransmissions can happen faster,
all MPTCP Join subtests checking ADD_ADDR counters accept more
ADD_ADDR than expected (if any). This is aligned with the previous
behaviour, when the ADD_ADDR RTO was lowered down to 1 second.
- Patch 3: Some CIs have reported that some MPTCP Join signalling tests
were unstable. It seems that it is due to the time it can take in slow
environments to send a bunch of ADD_ADDR notifications and wait each
time for their echo reply. Use a longer transfer to avoid such errors.
v1: https://lore.kernel.org/d5397026-92eb-4a43-9534-954b43ab9305@kernel.org
====================
Link: https://patch.msgid.link/20250907-net-next-mptcp-add_addr-retrans-adapt-v1-0-824cc805772b@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When many ADD_ADDR need to be sent, it can take some time to send each
of them, and create new subflows. Some CIs seem to occasionally have
issues with these tests, especially with "debug" kernels.
Two subtests will now run for a slightly longer time: the last two where
3 or more ADD_ADDR are sent during the test.
Reviewed-by: Geliang Tang <geliang@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/20250907-net-next-mptcp-add_addr-retrans-adapt-v1-3-824cc805772b@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
ADD_ADDR can be retransmitted, and with, the parent commit, these
retransmissions can be sent quicker: from 2 minutes to less than one
second.
To avoid false positives where retransmitted ADD_ADDR causes higher
counters than expected, it is required to be more tolerant. Errors are
now only reported when fewer ADD_ADDRs have been sent/received, except
if no ADD_ADDR are expected.
Before the parent commit, the tolerance was present for each tests where
the ADD_ADDR could be retransmitted in a reasonable time (1 sec). Now
that all tests can have retransmitted ADD_ADDR, it is normal to apply
the same tolerance for all tests.
An alternative could be to disable the ADD_ADDR retransmissions by
default, but that's changing the default kernel behaviour. Plus,
ADD_ADDR retransmissions can be required for some tests. To avoid adding
exceptions to many tests, it seems better to increase the tolerance.
Later, we could add a new MIB counter to identify the ADD_ADDR
retransmissions, and remove the tolerance when this counter is
available.
Reviewed-by: Geliang Tang <geliang@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/20250907-net-next-mptcp-add_addr-retrans-adapt-v1-2-824cc805772b@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Currently the ADD_ADDR option is retransmitted with a fixed timeout. This
patch makes the retransmission timeout adaptive by using the maximum RTO
among all the subflows, while still capping it at the configured maximum
value (add_addr_timeout_max). This improves responsiveness when
establishing new subflows.
Specifically:
1. Adds mptcp_adjust_add_addr_timeout() helper to compute the adaptive
timeout.
2. Uses maximum subflow RTO (icsk_rto) when available.
3. Applies exponential backoff based on retransmission count.
4. Maintains fallback to configured max timeout when no RTO data exists.
This slightly changes the behaviour of the MPTCP "add_addr_timeout"
sysctl knob to be used as a maximum instead of a fixed value. But this
is seen as an improvement: the ADD_ADDR might be sent quicker than
before to improve the overall MPTCP connection. Also, the default
value is set to 2 min, which was already way too long, and caused the
ADD_ADDR not to be retransmitted for connections shorter than 2 minutes.
Suggested-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Closes: https://github.com/multipath-tcp/mptcp_net-next/issues/576
Reviewed-by: Christoph Paasch <cpaasch@openai.com>
Signed-off-by: Geliang Tang <tanggeliang@kylinos.cn>
Reviewed-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/20250907-net-next-mptcp-add_addr-retrans-adapt-v1-1-824cc805772b@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue
Tony Nguyen says:
====================
idpf: add XDP support
Alexander Lobakin says:
Add XDP support (w/o XSk for now) to the idpf driver using the libeth_xdp
sublib. All possible verdicts, .ndo_xdp_xmit(), multi-buffer etc. are here.
In general, nothing outstanding comparing to ice, except performance --
let's say, up to 2x for .ndo_xdp_xmit() on certain platforms and
scenarios.
idpf doesn't support VLAN Rx offload, so only the hash hint is
available for now.
Patches 1-7 are prereqs, without which XDP would either not work at all
or work slower/worse/...
* '200GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue:
idpf: add XDP RSS hash hint
idpf: add support for .ndo_xdp_xmit()
idpf: add support for XDP on Rx
idpf: use generic functions to build xdp_buff and skb
idpf: implement XDP_SETUP_PROG in ndo_bpf for splitq
idpf: prepare structures to support XDP
idpf: add support for nointerrupt queues
idpf: remove SW marker handling from NAPI
idpf: add 4-byte completion descriptor definition
idpf: link NAPIs to queues
idpf: use a saner limit for default number of queues to allocate
idpf: fix Rx descriptor ready check barrier in splitq
xdp, libeth: make the xdp_init_buff() micro-optimization generic
====================
Link: https://patch.msgid.link/20250908195748.1707057-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Matthieu Baerts says:
====================
mptcp: misc fixes for v6.17-rc6
Here are various unrelated fixes:
- Patch 1: Fix a wrong attribute type in the MPTCP Netlink specs. A fix
for v6.7.
- Patch 2: Avoid mentioning a deprecated MPTCP sysctl knob in the doc. A
fix for v6.15.
- Patch 3: Handle new warnings from ShellCheck v0.11.0. This prevents
some warnings reported by some CIs. If it is not a good material for
'net', please drop.
====================
Link: https://patch.msgid.link/20250908-net-mptcp-misc-fixes-6-17-rc5-v1-0-5f2168a66079@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This v0.11.0 version introduces SC2329:
Warn when (non-escaping) functions are never invoked.
Except that, similar to SC2317, ShellCheck is currently unable to figure
out functions that are invoked via trap, or indirectly, when calling
functions via variables. It is then needed to disable this new SC2329.
Reviewed-by: Geliang Tang <geliang@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250908-net-mptcp-misc-fixes-6-17-rc5-v1-3-5f2168a66079@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The net.mptcp.pm_type sysctl knob has been deprecated in v6.15,
net.mptcp.path_manager should be used instead.
Adapt the section about path managers to suggest using the new sysctl
knob instead of the deprecated one.
Fixes: 595c26d122d1 ("mptcp: sysctl: set path manager by name")
Cc: stable@vger.kernel.org
Reviewed-by: Geliang Tang <geliang@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250908-net-mptcp-misc-fixes-6-17-rc5-v1-2-5f2168a66079@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This attribute is used as a signed number in the code in pm_netlink.c:
nla_put_s32(skb, MPTCP_ATTR_IF_IDX, ssk->sk_bound_dev_if))
The specs should then reflect that. Note that other 'if-idx' attributes
from the same .yaml file use a signed number as well.
Fixes: bc8aeb2045e2 ("Documentation: netlink: add a YAML spec for mptcp")
Cc: stable@vger.kernel.org
Reviewed-by: Geliang Tang <geliang@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/20250908-net-mptcp-misc-fixes-6-17-rc5-v1-1-5f2168a66079@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In some cases it's reasonable to describe DP lanes and AUX signal lines
separately in the DT. One of the typical reasons is if the source of DP
signals can support either USB-C or DP connections. In such a case the
transmitter of DP signals have separate ports: one for SS lanes and
another one for SBU / AUX signals.
Instead of leaving AUX signals from the controller unconnected, add an
option to the DT schema to AUX signal lines separately from the main
link lanes.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250907-dp-conenctor-sbu-v1-1-de79c0fcd64d@oss.qualcomm.com
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
|
|
Document established Devicetree bindings maintainers review practice:
Properties having differences per each device in the binding, e.g.
different constraints for lists or different allowed values, should
still be defined in top-level 'properties' section and only customized
in 'if:then:'.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20250904142400.179955-2-krzysztof.kozlowski@linaro.org
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
|
|
Users reported a scenario where MPTCP connections that were configured
with SO_KEEPALIVE prior to connect would fail to enable their keepalives
if MTPCP fell back to TCP mode.
After investigating, this affects keepalives for any connection where
sync_socket_options is called on a socket that is in the closed or
listening state. Joins are handled properly. For connects,
sync_socket_options is called when the socket is still in the closed
state. The tcp_set_keepalive() function does not act on sockets that
are closed or listening, hence keepalive is not immediately enabled.
Since the SO_KEEPOPEN flag is absent, it is not enabled later in the
connect sequence via tcp_finish_connect. Setting the keepalive via
sockopt after connect does work, but would not address any subsequently
created flows.
Fortunately, the fix here is straight-forward: set SOCK_KEEPOPEN on the
subflow when calling sync_socket_options.
The fix was valdidated both by using tcpdump to observe keepalive
packets not being sent before the fix, and being sent after the fix. It
was also possible to observe via ss that the keepalive timer was not
enabled on these sockets before the fix, but was enabled afterwards.
Fixes: 1b3e7ede1365 ("mptcp: setsockopt: handle SO_KEEPALIVE and SO_PRIORITY")
Cc: stable@vger.kernel.org
Signed-off-by: Krister Johansen <kjlx@templeofstupid.com>
Reviewed-by: Geliang Tang <geliang@kernel.org>
Reviewed-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/aL8dYfPZrwedCIh9@templeofstupid.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Syzkaller managed to lock the lower device via ETHTOOL_SFEATURES:
netdev_lock include/linux/netdevice.h:2761 [inline]
netdev_lock_ops include/net/netdev_lock.h:42 [inline]
netdev_sync_lower_features net/core/dev.c:10649 [inline]
__netdev_update_features+0xcb1/0x1be0 net/core/dev.c:10819
netdev_update_features+0x6d/0xe0 net/core/dev.c:10876
macsec_notify+0x2f5/0x660 drivers/net/macsec.c:4533
notifier_call_chain+0x1b3/0x3e0 kernel/notifier.c:85
call_netdevice_notifiers_extack net/core/dev.c:2267 [inline]
call_netdevice_notifiers net/core/dev.c:2281 [inline]
netdev_features_change+0x85/0xc0 net/core/dev.c:1570
__dev_ethtool net/ethtool/ioctl.c:3469 [inline]
dev_ethtool+0x1536/0x19b0 net/ethtool/ioctl.c:3502
dev_ioctl+0x392/0x1150 net/core/dev_ioctl.c:759
It happens because lower features are out of sync with the upper:
__dev_ethtool (real_dev)
netdev_lock_ops(real_dev)
ETHTOOL_SFEATURES
__netdev_features_change
netdev_sync_upper_features
disable LRO on the lower
if (old_features != dev->features)
netdev_features_change
fires NETDEV_FEAT_CHANGE
macsec_notify
NETDEV_FEAT_CHANGE
netdev_update_features (for each macsec dev)
netdev_sync_lower_features
if (upper_features != lower_features)
netdev_lock_ops(lower) # lower == real_dev
stuck
...
netdev_unlock_ops(real_dev)
Per commit af5f54b0ef9e ("net: Lock lower level devices when updating
features"), we elide the lock/unlock when the upper and lower features
are synced. Makes sure the lower (real_dev) has proper features after
the macsec link has been created. This makes sure we never hit the
situation where we need to sync upper flags to the lower.
Reported-by: syzbot+7e0f89fb6cae5d002de0@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=7e0f89fb6cae5d002de0
Fixes: 7e4d784f5810 ("net: hold netdev instance lock during rtnetlink operations")
Signed-off-by: Stanislav Fomichev <sdf@fomichev.me>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Link: https://patch.msgid.link/20250908173614.3358264-1-sdf@fomichev.me
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
first_remote_rcu() can return NULL if the FDB entry points to an FDB
nexthop group instead of a remote destination. However, unlike other
users of first_remote_rcu(), NPD cannot currently happen in
vxlan_fdb_find_uc() as it is only invoked by one driver which vetoes the
creation of FDB nexthops.
Make the function more robust by making sure the remote destination is
only dereferenced if it is not NULL.
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Wang Liang <wangliang74@huawei.com>
Reviewed-by: Nikolay Aleksandrov <razor@blackwall.org>
Link: https://patch.msgid.link/20250908075141.125087-1-idosch@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This is a development artifact of commit a76f26f7a81e ("net: phy:
aquantia: support phy-mode = "10g-qxgmii" on NXP SPF-30841 (AQR412C)").
This function name isn't used. Instead we have aqr_build_fingerprint()
in aquantia_main.c.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250908134313.315406-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
ndo hwtstamp callbacks are expected to run under the per-device ops
lock. Make the lower get/set paths consistent with the rest of ndo
invocations.
Kernel log:
WARNING: CPU: 13 PID: 51364 at ./include/net/netdev_lock.h:70 __netdev_update_features+0x4bd/0xe60
...
RIP: 0010:__netdev_update_features+0x4bd/0xe60
...
Call Trace:
<TASK>
netdev_update_features+0x1f/0x60
mlx5_hwtstamp_set+0x181/0x290 [mlx5_core]
mlx5e_hwtstamp_set+0x19/0x30 [mlx5_core]
dev_set_hwtstamp_phylib+0x9f/0x220
dev_set_hwtstamp_phylib+0x9f/0x220
dev_set_hwtstamp+0x13d/0x240
dev_ioctl+0x12f/0x4b0
sock_ioctl+0x171/0x370
__x64_sys_ioctl+0x3f7/0x900
? __sys_setsockopt+0x69/0xb0
do_syscall_64+0x6f/0x2e0
entry_SYSCALL_64_after_hwframe+0x4b/0x53
...
</TASK>
....
---[ end trace 0000000000000000 ]---
Note that the mlx5_hwtstamp_set and mlx5e_hwtstamp_set functions shown
in the trace come from an in progress patch converting the legacy ioctl
to ndo_hwtstamp_get/set and are not present in mainline.
Fixes: ffb7ed19ac0a ("net: hold netdev instance lock during ioctl operations")
Signed-off-by: Carolina Jubran <cjubran@nvidia.com>
Reviewed-by: Cosmin Ratiu <cratiu@nvidia.com>
Reviewed-by: Dragos Tatulea <dtatulea@nvidia.com>
Link: https://patch.msgid.link/20250907080821.2353388-1-cjubran@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Heiner Kallweit says:
====================
net: phy: fixed_phy: improvements
This series contains a number of improvements.
No functional change intended.
====================
Link: https://patch.msgid.link/e81be066-cc23-4055-aed7-2fbc86da1ff7@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Use two separate static variables instead of the struct, this allows
to simplify the code.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Factor out the functionality to search for a fixed_phy matching an
address. This improves readability of the code.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
After the recent removal of gpio support member no_carrier isn't
needed any longer.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The two callers of __fixed_phy_add() both pass PHY_POLL, so we can
remove the irq argument to simplify the function.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Rename of open files in SMB2+ has been broken for a very long time,
resulting in data loss as the CIFS client would fail the rename(2)
call with -ENOENT and then removing the target file.
Fix this by implementing ->rename_pending_delete() for SMB2+, which
will rename busy files to random filenames (e.g. silly rename) during
unlink(2) or rename(2), and then marking them to delete-on-close.
Besides, introduce a FIND_WR_NO_PENDING_DELETE flag to prevent open(2)
from reusing open handles that had been marked as delete pending.
Handle it in cifs_get_readable_path() as well.
Reported-by: Jean-Baptiste Denis <jbdenis@pasteur.fr>
Closes: https://marc.info/?i=16aeb380-30d4-4551-9134-4e7d1dc833c0@pasteur.fr
Reviewed-by: David Howells <dhowells@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Paulo Alcantara (Red Hat) <pc@manguebit.org>
Cc: Frank Sorenson <sorenson@redhat.com>
Cc: Olga Kornievskaia <okorniev@redhat.com>
Cc: Benjamin Coddington <bcodding@redhat.com>
Cc: Scott Mayhew <smayhew@redhat.com>
Cc: linux-cifs@vger.kernel.org
Signed-off-by: Steve French <stfrench@microsoft.com>
|
|
The blamed commit changed the conditions which phylib uses to stop
and start the state machine in the suspend and resume paths, and
while improving it, has caused two issues.
The original code used this test:
phydev->attached_dev && phydev->adjust_link
and if true, the paths would handle the PHY state machine. This test
evaluates true for normal drivers that are using phylib directly
while the PHY is attached to the network device, but false in all
other cases, which include the following cases:
- when the PHY has never been attached to a network device.
- when the PHY has been detached from a network device (as phy_detach()
sets phydev->attached_dev to NULL, phy_disconnect() calls
phy_detach() and additionally sets phydev->adjust_link NULL.)
- when phylink is using the driver (as phydev->adjust_link is NULL.)
Only the third case was incorrect, and the blamed commit attempted to
fix this by changing this test to (simplified for brevity, see
phy_uses_state_machine()):
phydev->phy_link_change == phy_link_change ?
phydev->attached_dev && phydev->adjust_link : true
However, this also incorrectly evaluates true in the first two cases.
Fix the first case by ensuring that phy_uses_state_machine() returns
false when phydev->phy_link_change is NULL.
Fix the second case by ensuring that phydev->phy_link_change is set to
NULL when phy_detach() is called.
Reported-by: Xu Yang <xu.yang_2@nxp.com>
Link: https://lore.kernel.org/r/20250806082931.3289134-1-xu.yang_2@nxp.com
Fixes: fc75ea20ffb4 ("net: phy: allow MDIO bus PM ops to start/stop state machine for phylink-controlled PHY")
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://patch.msgid.link/E1uvMEz-00000003Aoe-3qWe@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Correct typos in ipv4/udp.c comments for clarity:
"Encapulation" -> "Encapsulation"
"measureable" -> "measurable"
"tacking care" -> "taking care"
No functional changes.
Signed-off-by: Alok Tiwari <alok.a.tiwari@oracle.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250907192535.3610686-1-alok.a.tiwari@oracle.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The pmtu test takes nearly an hour when run on a debug kernel
(10min on a normal kernel, so the debug slow down is quite significant).
NIPA tries to ensure all results are delivered by a certain deadline
so this prevents it from retrying the test in case of a flake.
Looks like one of the slowest operations in the test is calling out
to ./openvswitch/ovs-dpctl.py to remove potential leftover OvS interfaces.
Check whether the interfaces exist in the first place in sysfs,
since it can be done directly in bash it is very fast.
This should save us around 20-30% of the test runtime.
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250906214535.3204785-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
RaspberryPi 5 presents two USB 2.0 and two USB 3.0 ports.
Configure and enable the USB nodes in the devicetree.
Signed-off-by: Andrea della Porta <andrea.porta@suse.com>
Link: https://lore.kernel.org/r/c6b17f0f896b5cdd790fc10aeb2b76b71df9b58d.1757065053.git.andrea.porta@suse.com
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
|
|
fcnal-test.sh takes almost hour and a half to finish.
The tests are already grouped into ipv4, ipv6 and other.
Run those groups separately.
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://patch.msgid.link/20250908201021.270681-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The encryption layer can't handle the padding iovs, so flatten the
compound request into a single buffer with required padding to prevent
the server from dropping the connection when finding unaligned
compound requests.
Fixes: bc925c1216f0 ("smb: client: improve compound padding in encryption")
Signed-off-by: Paulo Alcantara (Red Hat) <pc@manguebit.org>
Reviewed-by: David Howells <dhowells@redhat.com>
Cc: linux-cifs@vger.kernel.org
Cc: stable@vger.kernel.org
Signed-off-by: Steve French <stfrench@microsoft.com>
|
|
Currently, calling bpf_map_kmalloc_node() from __bpf_async_init() can
cause various locking issues; see the following stack trace (edited for
style) as one example:
...
[10.011566] do_raw_spin_lock.cold
[10.011570] try_to_wake_up (5) double-acquiring the same
[10.011575] kick_pool rq_lock, causing a hardlockup
[10.011579] __queue_work
[10.011582] queue_work_on
[10.011585] kernfs_notify
[10.011589] cgroup_file_notify
[10.011593] try_charge_memcg (4) memcg accounting raises an
[10.011597] obj_cgroup_charge_pages MEMCG_MAX event
[10.011599] obj_cgroup_charge_account
[10.011600] __memcg_slab_post_alloc_hook
[10.011603] __kmalloc_node_noprof
...
[10.011611] bpf_map_kmalloc_node
[10.011612] __bpf_async_init
[10.011615] bpf_timer_init (3) BPF calls bpf_timer_init()
[10.011617] bpf_prog_xxxxxxxxxxxxxxxx_fcg_runnable
[10.011619] bpf__sched_ext_ops_runnable
[10.011620] enqueue_task_scx (2) BPF runs with rq_lock held
[10.011622] enqueue_task
[10.011626] ttwu_do_activate
[10.011629] sched_ttwu_pending (1) grabs rq_lock
...
The above was reproduced on bpf-next (b338cf849ec8) by modifying
./tools/sched_ext/scx_flatcg.bpf.c to call bpf_timer_init() during
ops.runnable(), and hacking the memcg accounting code a bit to make
a bpf_timer_init() call more likely to raise an MEMCG_MAX event.
We have also run into other similar variants (both internally and on
bpf-next), including double-acquiring cgroup_file_kn_lock, the same
worker_pool::lock, etc.
As suggested by Shakeel, fix this by using __GFP_HIGH instead of
GFP_ATOMIC in __bpf_async_init(), so that e.g. if try_charge_memcg()
raises an MEMCG_MAX event, we call __memcg_memory_event() with
@allow_spinning=false and avoid calling cgroup_file_notify() there.
Depends on mm patch
"memcg: skip cgroup_file_notify if spinning is not allowed":
https://lore.kernel.org/bpf/20250905201606.66198-1-shakeel.butt@linux.dev/
v0 approach s/bpf_map_kmalloc_node/bpf_mem_alloc/
https://lore.kernel.org/bpf/20250905061919.439648-1-yepeilin@google.com/
v1 approach:
https://lore.kernel.org/bpf/20250905234547.862249-1-yepeilin@google.com/
Fixes: b00628b1c7d5 ("bpf: Introduce bpf timers.")
Suggested-by: Shakeel Butt <shakeel.butt@linux.dev>
Signed-off-by: Peilin Ye <yepeilin@google.com>
Link: https://lore.kernel.org/r/20250909095222.2121438-1-yepeilin@google.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
OpenWRT users reported regression on ARMv6 devices after updating to latest
HEAD, where tcpdump filter:
tcpdump "not ether host 3c37121a2b3c and not ether host 184ecbca2a3a \
and not ether host 14130b4d3f47 and not ether host f0f61cf440b7 \
and not ether host a84b4dedf471 and not ether host d022be17e1d7 \
and not ether host 5c497967208b and not ether host 706655784d5b"
fails with warning: "Kernel filter failed: No error information"
when using config:
# CONFIG_BPF_JIT_ALWAYS_ON is not set
CONFIG_BPF_JIT_DEFAULT_ON=y
The issue arises because commits:
1. "bpf: Fix array bounds error with may_goto" changed default runtime to
__bpf_prog_ret0_warn when jit_requested = 1
2. "bpf: Avoid __bpf_prog_ret0_warn when jit fails" returns error when
jit_requested = 1 but jit fails
This change restores interpreter fallback capability for BPF programs with
stack size <= 512 bytes when jit fails.
Reported-by: Felix Fietkau <nbd@nbd.name>
Closes: https://lore.kernel.org/bpf/2e267b4b-0540-45d8-9310-e127bf95fc63@nbd.name/
Fixes: 6ebc5030e0c5 ("bpf: Fix array bounds error with may_goto")
Signed-off-by: KaFai Wan <kafai.wan@linux.dev>
Acked-by: Eduard Zingerman <eddyz87@gmail.com>
Link: https://lore.kernel.org/r/20250909144614.2991253-1-kafai.wan@linux.dev
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
Currently, out of all 3 types of waiters in the rqspinlock slow path
(i.e., pending bit waiter, wait queue head waiter, and wait queue
non-head waiter), only the pending bit waiter and wait queue head
waiters apply deadlock checks and a timeout on their waiting loop. The
assumption here was that the wait queue head's forward progress would be
sufficient to identify cases where the lock owner or pending bit waiter
is stuck, and non-head waiters relying on the head waiter would prove to
be sufficient for their own forward progress.
However, the head waiter itself can be preempted by a non-head waiter
for the same lock (AA) or a different lock (ABBA) in a manner that
impedes its forward progress. In such a case, non-head waiters not
performing deadlock and timeout checks becomes insufficient, and the
system can enter a state of lockup.
This is typically not a concern with non-NMI lock acquisitions, as lock
holders which in run in different contexts (IRQ, non-IRQ) use "irqsave"
variants of the lock APIs, which naturally excludes such lock holders
from preempting one another on the same CPU.
It might seem likely that a similar case may occur for rqspinlock when
programs are attached to contention tracepoints (begin, end), however,
these tracepoints either precede the enqueue into the wait queue, or
succeed it, therefore cannot be used to preempt a head waiter's waiting
loop.
We must still be careful against nested kprobe and fentry programs that
may attach to the middle of the head's waiting loop to stall forward
progress and invoke another rqspinlock acquisition that proceeds as a
non-head waiter. To this end, drop CC_FLAGS_FTRACE from the rqspinlock.o
object file.
For now, this issue is resolved by falling back to a repeated trylock on
the lock word from NMI context, while performing the deadlock checks to
break out early in case forward progress is impossible, and use the
timeout as a final fallback.
A more involved fix to terminate the queue when such a condition occurs
will be made as a follow up. A selftest to stress this aspect of nested
NMI/non-NMI locking attempts will be added in a subsequent patch to the
bpf-next tree when this fix lands and trees are synchronized.
Reported-by: Josef Bacik <josef@toxicpanda.com>
Fixes: 164c246571e9 ("rqspinlock: Protect waiters in queue from stalls")
Signed-off-by: Kumar Kartikeya Dwivedi <memxor@gmail.com>
Link: https://lore.kernel.org/r/20250909184959.3509085-1-memxor@gmail.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
Core functions like `to_result` should have good documentation.
Thus improve it, including adding an example of how to perform early
returns with it.
Reviewed-by: Benno Lossin <lossin@kernel.org>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Miguel Ojeda <ojeda@kernel.org>
|
|
This constructor is public since commit 5ed147473458 ("rust: error:
make conversion functions public"), and we will refer to it from the
documentation of `to_result` in a later commit.
Thus improve its documentation, including adding examples.
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Reviewed-by: Benno Lossin <lossin@kernel.org>
Signed-off-by: Miguel Ojeda <ojeda@kernel.org>
|
|
Eryk reported an issue that I have put under Closes: tag, related to
umem addrs being prematurely produced onto pool's completion queue.
Let us make the skb's destructor responsible for producing all addrs
that given skb used.
Commit from fixes tag introduced the buggy behavior, it was not broken
from day 1, but rather when xsk multi-buffer got introduced.
In order to mitigate performance impact as much as possible, mimic the
linear and frag parts within skb by storing the first address from XSK
descriptor at sk_buff::destructor_arg. For fragments, store them at ::cb
via list. The nodes that will go onto list will be allocated via
kmem_cache. xsk_destruct_skb() will consume address stored at
::destructor_arg and optionally go through list from ::cb, if count of
descriptors associated with this particular skb is bigger than 1.
Previous approach where whole array for storing UMEM addresses from XSK
descriptors was pre-allocated during first fragment processing yielded
too big performance regression for 64b traffic. In current approach
impact is much reduced on my tests and for jumbo frames I observed
traffic being slower by at most 9%.
Magnus suggested to have this way of processing special cased for
XDP_SHARED_UMEM, so we would identify this during bind and set different
hooks for 'backpressure mechanism' on CQ and for skb destructor, but
given that results looked promising on my side I decided to have a
single data path for XSK generic Tx. I suppose other auxiliary stuff
would have to land as well in order to make it work.
Fixes: b7f72a30e9ac ("xsk: introduce wrappers and helpers for supporting multi-buffer in Tx path")
Reported-by: Eryk Kubanski <e.kubanski@partner.samsung.com>
Closes: https://lore.kernel.org/netdev/20250530103456.53564-1-e.kubanski@partner.samsung.com/
Acked-by: Stanislav Fomichev <sdf@fomichev.me>
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Jason Xing <kerneljasonxing@gmail.com>
Reviewed-by: Jason Xing <kerneljasonxing@gmail.com>
Link: https://lore.kernel.org/r/20250904194907.2342177-1-maciej.fijalkowski@intel.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
Unfortunately Mykola won't participate in BPF selftests maintenance
anymore. Remove the entry on his behalf.
Acked-by: Mykola Lysenko <nickolay.lysenko@gmail.com>
Signed-off-by: Eduard Zingerman <eddyz87@gmail.com>
Link: https://lore.kernel.org/r/20250909171638.2417272-1-eddyz87@gmail.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
Rong Tao says:
====================
Fix bpf_strnstr() wrong 'len' parameter, bpf_strnstr("open", "open", 4)
should return 0 instead of -ENOENT. And fix a more general case when s2
is a suffix of the first len characters of s1.
====================
Link: https://patch.msgid.link/tencent_E72A37AF03A3B18853066E421B5969976208@qq.com
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
Ilya Leoshkevich says:
====================
selftests/bpf: Fix "expression result unused" warnings with icecc
v3: https://lore.kernel.org/bpf/20250827194929.416969-1-iii@linux.ibm.com/
v3 -> v4: Go back to the original solution (Yonghong, Alexei).
v2: https://lore.kernel.org/bpf/20250827130519.411700-1-iii@linux.ibm.com/
v2 -> v3: Do not touch libbpf, explain how having two function
declarations works (Andrii).
Fix bpf-gcc build (CI).
v1: https://lore.kernel.org/bpf/20250508113804.304665-1-iii@linux.ibm.com/
v1 -> v2: Annotate bpf_obj_new_impl() with __must_check (Alexei).
Add an explanation about icecc.
I took another look at the "expression result unused" warnings I've
been seeing, and it turned out that the root cause was the icecc
compiler wrapper and what I consider a clang bug. Back then I've
reported that the problem was reproducible with plain clang, but now
I see that it was clearly a mixup, sorry about that.
The solution is to add a few awkward (void) casts. I've added a
detailed explanation of why they are helpful to the commit message.
====================
Link: https://patch.msgid.link/20250829030017.102615-1-iii@linux.ibm.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
Add tests for bpf_strnstr():
bpf_strnstr("", "", 0) = 0
bpf_strnstr("hello world", "hello", 5) = 0
bpf_strnstr(str, "hello", 4) = -ENOENT
bpf_strnstr("", "a", 0) = -ENOENT
Signed-off-by: Rong Tao <rongtao@cestc.cn>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/tencent_2ED218F8082565C95D86A804BDDA8DBA200A@qq.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
icecc is a compiler wrapper that distributes compile jobs over a build
farm [1]. It works by sending toolchain binaries and preprocessed
source code to remote machines.
Unfortunately using it with BPF selftests causes build failures due to
a clang bug [2]. The problem is that clang suppresses the
-Wunused-value warning if the unused expression comes from a macro
expansion. Since icecc compiles preprocessed source code, this
information is not available. This leads to -Wunused-value false
positives.
obj_new_no_struct() and obj_new_acq() use the bpf_obj_new() macro and
discard the result. arena_spin_lock_slowpath() uses two macros that
produce values and ignores the results. Add (void) casts to explicitly
indicate that this is intentional and suppress the warning.
An alternative solution is to change the macros to not produce values.
This would work today for the arena_spin_lock_slowpath() issue, but in
the future there may appear users who need them. Another potential
solution is to replace these macros with functions. Unfortunately this
would not work, because these macros work with unknown types and
control flow.
[1] https://github.com/icecc/icecream
[2] https://github.com/llvm/llvm-project/issues/142614
Signed-off-by: Ilya Leoshkevich <iii@linux.ibm.com>
Acked-by: Yonghong Song <yonghong.song@linux.dev>
Link: https://lore.kernel.org/r/20250829030017.102615-2-iii@linux.ibm.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
bpf_strnstr() should not treat the ending '\0' of s2 as a matching character
if the parameter 'len' equal to s2 string length, for example:
1. bpf_strnstr("openat", "open", 4) = -ENOENT
2. bpf_strnstr("openat", "open", 5) = 0
This patch makes (1) return 0, fix just the `len == strlen(s2)` case.
And fix a more general case when s2 is a suffix of the first len
characters of s1.
Fixes: e91370550f1f ("bpf: Add kfuncs for read-only string operations")
Signed-off-by: Rong Tao <rongtao@cestc.cn>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/tencent_17DC57B9D16BC443837021BEACE84B7C1507@qq.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
Small cleanup and test extension to probe the bpf_crypto_{encrypt,decrypt}()
kfunc when a bad dst buffer is passed in to assert that an error is returned.
Also, encrypt_sanity() and skb_crypto_setup() were explicit to set the global
status variable to zero before any test, so do the same for decrypt_sanity().
Do not explicitly zero the on-stack err before bpf_crypto_ctx_create() given
the kfunc is expected to do it internally for the success case.
Before kernel fix:
# ./vmtest.sh -- ./test_progs -t crypto
[...]
[ 1.531200] bpf_testmod: loading out-of-tree module taints kernel.
[ 1.533388] bpf_testmod: module verification failed: signature and/or required key missing - tainting kernel
#87/1 crypto_basic/crypto_release:OK
#87/2 crypto_basic/crypto_acquire:OK
#87 crypto_basic:OK
test_crypto_sanity:PASS:skel open 0 nsec
test_crypto_sanity:PASS:ip netns add crypto_sanity_ns 0 nsec
test_crypto_sanity:PASS:ip -net crypto_sanity_ns -6 addr add face::1/128 dev lo nodad 0 nsec
test_crypto_sanity:PASS:ip -net crypto_sanity_ns link set dev lo up 0 nsec
test_crypto_sanity:PASS:open_netns 0 nsec
test_crypto_sanity:PASS:AF_ALG init fail 0 nsec
test_crypto_sanity:PASS:if_nametoindex lo 0 nsec
test_crypto_sanity:PASS:skb_crypto_setup fd 0 nsec
test_crypto_sanity:PASS:skb_crypto_setup 0 nsec
test_crypto_sanity:PASS:skb_crypto_setup retval 0 nsec
test_crypto_sanity:PASS:skb_crypto_setup status 0 nsec
test_crypto_sanity:PASS:create qdisc hook 0 nsec
test_crypto_sanity:PASS:make_sockaddr 0 nsec
test_crypto_sanity:PASS:attach encrypt filter 0 nsec
test_crypto_sanity:PASS:encrypt socket 0 nsec
test_crypto_sanity:PASS:encrypt send 0 nsec
test_crypto_sanity:FAIL:encrypt status unexpected error: -5 (errno 95)
#88 crypto_sanity:FAIL
Summary: 1/2 PASSED, 0 SKIPPED, 1 FAILED
After kernel fix:
# ./vmtest.sh -- ./test_progs -t crypto
[...]
[ 1.540963] bpf_testmod: loading out-of-tree module taints kernel.
[ 1.542404] bpf_testmod: module verification failed: signature and/or required key missing - tainting kernel
#87/1 crypto_basic/crypto_release:OK
#87/2 crypto_basic/crypto_acquire:OK
#87 crypto_basic:OK
#88 crypto_sanity:OK
Summary: 2/2 PASSED, 0 SKIPPED, 0 FAILED
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Cc: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Link: https://lore.kernel.org/r/20250829143657.318524-2-daniel@iogearbox.net
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
Stanislav reported that in bpf_crypto_crypt() the destination dynptr's
size is not validated to be at least as large as the source dynptr's
size before calling into the crypto backend with 'len = src_len'. This
can result in an OOB write when the destination is smaller than the
source.
Concretely, in mentioned function, psrc and pdst are both linear
buffers fetched from each dynptr:
psrc = __bpf_dynptr_data(src, src_len);
[...]
pdst = __bpf_dynptr_data_rw(dst, dst_len);
[...]
err = decrypt ?
ctx->type->decrypt(ctx->tfm, psrc, pdst, src_len, piv) :
ctx->type->encrypt(ctx->tfm, psrc, pdst, src_len, piv);
The crypto backend expects pdst to be large enough with a src_len length
that can be written. Add an additional src_len > dst_len check and bail
out if it's the case. Note that these kfuncs are accessible under root
privileges only.
Fixes: 3e1c6f35409f ("bpf: make common crypto API for TC/XDP programs")
Reported-by: Stanislav Fort <disclosure@aisle.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Cc: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Reviewed-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Link: https://lore.kernel.org/r/20250829143657.318524-1-daniel@iogearbox.net
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
The RaspberryPi 5 has RP1 chipset containing two USB host controller,
while presenting two USB 2.0 and two USB 3.0 ports to the outside.
Add the relevant USB nodes to the devicetree.
Signed-off-by: Andrea della Porta <andrea.porta@suse.com>
Link: https://lore.kernel.org/r/16d753cb4bf37beb5e9c6f0e03576cf13708f27d.1757065053.git.andrea.porta@suse.com
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
|
|
There is no reason to require this to happen on first submitted IB only.
We need to wait for the queue to be idle, but it can be done at any
time (including when there are multiple video sessions active).
Signed-off-by: David Rosca <david.rosca@amd.com>
Reviewed-by: Leo Liu <leo.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 8908fdce0634a623404e9923ed2f536101a39db5)
Cc: stable@vger.kernel.org
|
