| Age | Commit message (Collapse) | Author |
|---|
|
Rename node name i2c-gpio to i2c to fix below CHECK_DTBS warnings:
arch/arm/boot/dts/nxp/imx/imx6ul-tx6ul-0010.dtb: / (karo,imx6ul-tx6ul): i2c-gpio: {'compatible': ['i2c-gpio'], '#address-cells': 1, '#size-cells': 0, 'pinctrl-names': ['default'], 'pinctrl-0': [[68]], 'sda-gpios': [[46, 1, 0]], 'scl-gpios': [[46, 0, 0]], 'clock-frequency': 400000, 'status': ['okay'], 'rtc@68': {'compatible': ['dallas,ds1339'], 'reg': [[104]], 'status': ['disabled']}} is not of type 'array'
from schema $id: http://devicetree.org/schemas/gpio/gpio-consumer.yaml#
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Rename touch to touchscreen.
Rename stmpe_touchscreen to touchscreen.
Rename stmpe_adc to adc.
Fix below CHECK_DTBS warning:
arch/arm/boot/dts/nxp/imx/imx7d-nitrogen7.dtb: touch@48 (ti,tsc2004): 'wakeup-gpios' does not match any of the regexes: '^pinctrl-[0-9]+$'
from schema $id: http://devicetree.org/schemas/input/touchscreen/ti,tsc2005.yaml#
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Remove redundant pinctrl-name because no pinctrl-0 existed to fix below
CHECK_DTBS warnings:
arch/arm/boot/dts/nxp/imx/imx6dl-hummingboard.dtb: pwm@2084000 (fsl,imx6q-pwm): 'pinctrl-0' is a dependency of 'pinctrl-names'
from schema $id: http://devicetree.org/schemas/pinctrl/pinctrl-consumer.yaml#
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Rename ethernet-phy to ethernet-phy@0 to fix below CHECK_DTB warnings:
arch/arm/boot/dts/nxp/imx/imx6dl-aristainetos2_4.dtb: ethernet@2188000 (fsl,imx6q-fec): mdio: Unevaluated properties are not allowed ('ethernet-phy' was unexpected)
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add interrupt-cells for pmic to fix below CHECK_DTBS warnings:
arm/boot/dts/nxp/imx/imx6dl-emcon-avari.dtb: pmic@58 (dlg,da9063): 'interrupt-controller' is a required property
from schema $id: http://devicetree.org/schemas/mfd/dlg,da9063.yaml
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Rename node name ds1672 to rtc to fix below CHECK_DTB warning:
arch/arm/boot/dts/nxp/imx/imx6dl-gw51xx.dtb: ds1672@68 (dallas,ds1672): $nodename:0: 'ds1672@68' does not match '^rtc(@.*|-([0-9]|[1-9][0-9]+))?$
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add key- prefix for gpio-keys and rename button_0 to button-0 to fix below
CHECK_DTB warning:
arch/arm/boot/dts/nxp/imx/imx6q-gw51xx.dtb: gpio-keys (gpio-keys): 'eeprom-wp', ... do not match any of the regexes: '^(button|...))$', 'pinctrl-[0-9]+
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add #address-cells for gsc20 to fix below CHECK_DTB warning:
arch/arm/boot/dts/nxp/imx/imx6dl-gw51xx.dtb: gsc@20 (gw,gsc): '#address-cells' is a required property
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
This adds support for TQMa91xx module attached to MBa91xxCA board.
TQMa91xx is a SOM series using i.MX91 SOC. The SOM features PMIC, RAM,
e-MMC and some optional peripherals like SPI-NOR, RTC, EEPROM,
gyroscope and secure element.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The 'eee-broken-1000t' flag disables Energy-Efficient Ethernet (EEE) on 1G
links as a workaround for PTP sync issues on older i.MX6 platforms.
Remove it since the i.MX93 have not such issue.
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Joy Zou <joy.zou@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add i.MX91 11x11 EVK board support.
- Enable ADC1.
- Enable lpuart1 and lpuart5.
- Enable network eqos and fec.
- Enable I2C bus and children nodes under I2C bus.
- Enable USB and related nodes.
- Enable uSDHC1 and uSDHC2.
- Enable Watchdog3.
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Pengfei Li <pengfei.li_1@nxp.com>
Signed-off-by: Joy Zou <joy.zou@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The i.MX 91 family features an Arm Cortex-A55 running at up to 1.4GHz,
support for modern LPDDR4 memory to enable platform longevity, along
with a rich set of peripherals targeting medical, industrial and
consumer IoT market segments.
The mainly difference between i.MX91 and i.MX93 is as follows:
- i.MX91 removed some clocks and modified the names of some clocks.
- i.MX91 only has one A core.
- i.MX91 has different pinmux.
Tested-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Joy Zou <joy.zou@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The design of i.MX91 platform is very similar to i.MX93 and only
some small differences.
If the imx91.dtsi include the imx93.dtsi, each add to imx93.dtsi
requires an remove in imx91.dtsi for this unique to i.MX93, e.g. NPU.
The i.MX91 isn't the i.MX93 subset, if the imx93.dtsi include the
imx91.dtsi, the same problem will occur.
Common + delta is better than common - delta, so add imx91_93_common.dtsi
for i.MX91 and i.MX93, then the imx93.dtsi and imx91.dtsi will include the
imx91_93_common.dtsi.
Rename imx93.dtsi to imx91_93_common.dtsi and move i.MX93 specific
part from imx91_93_common.dtsi to imx93.dtsi.
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Joy Zou <joy.zou@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The aliases is board level property rather than soc property, so move
these to each boards.
Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Joy Zou <joy.zou@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
SolidRun Clearfog CX and Honeycomb have LX2160A PEX3 and PEX5 exposed on
physical connectors.
Vendor U-Boot used to patch status properties such that it went
undiscovered these nodes have their status set disabled.
Set status okay for pcie3 and pcie5 nodes.
Signed-off-by: Josua Mayer <josua@solid-run.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
SolidRun LX2160A CEX-7 module has interrupts wired for both the rtc and
ethernet phy.
Add description for those interrupts to the rtc and phy nodes.
Signed-off-by: Josua Mayer <josua@solid-run.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add description for the SolidRun i.MX8M Plus based System on Module, and
the CuBox-M.
The SoM features:
- 2x 1Gbps Ethernet with PHY
- eMMC
- 1/2/3/8GB DDR
- MIPI-CSI Camera Connector (not described without specific camera)
The CuBox-M is a complete product with enclosure featuring:
- 1x 1Gbps RJ45 Ethernet Port
- 2x USB-3.0 Type A
- HDMI connector
- microSD connector
- microUSB connector for console (using fdtdi chip)
- IR receiver
- RTC with backup battery
Signed-off-by: Josua Mayer <josua@solid-run.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Decoding interrupt-map is tricky, because it consists of five
components. Use known GIC_SPI define in final interrupt specifier
component makes easier to read.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add missing address-cells 0 to GIC interrupt node to silence W=1
warning:
imx8-ss-hsio.dtsi:71.3-74.28: Warning (interrupt_map): /bus@5f000000/pcie@5f010000:interrupt-map:
Missing property '#address-cells' in node /interrupt-controller@51a00000, using 0 as fallback
Value '0' is correct because:
1. GIC interrupt controller does not have children,
2. interrupt-map property (in PCI node) consists of five components and
the fourth component "parent unit address", which size is defined by
'#address-cells' of the node pointed to by the interrupt-parent
component, is not used (=0)
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add missing address-cells 0 to GIC interrupt node to silence W=1
warning:
imx8qm-ss-hsio.dtsi:83.3-86.28: Warning (interrupt_map): /bus@5f000000/pcie@5f010000:interrupt-map:
Missing property '#address-cells' in node /interrupt-controller@51a00000, using 0 as fallback
Value '0' is correct because:
1. GIC interrupt controller does not have children,
2. interrupt-map property (in PCI node) consists of five components and
the fourth component "parent unit address", which size is defined by
'#address-cells' of the node pointed to by the interrupt-parent
component, is not used (=0)
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add missing address-cells 0 to GIC interrupt node to silence W=1
warning:
imx8mq.dtsi:1746.4-1749.43: Warning (interrupt_map): /soc@0/pcie@33800000:interrupt-map:
Missing property '#address-cells' in node /soc@0/interrupt-controller@38800000, using 0 as fallback
Value '0' is correct because:
1. GIC interrupt controller does not have children,
2. interrupt-map property (in PCI node) consists of five components and
the fourth component "parent unit address", which size is defined by
'#address-cells' of the node pointed to by the interrupt-parent
component, is not used (=0)
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add missing address-cells 0 to GIC interrupt node to silence W=1
warning:
imx8mp.dtsi:2184.4-2187.29: Warning (interrupt_map): /soc@0/pcie@33800000:interrupt-map:
Missing property '#address-cells' in node /soc@0/interrupt-controller@38800000, using 0 as fallback
Value '0' is correct because:
1. GIC interrupt controller does not have children,
2. interrupt-map property (in PCI node) consists of five components and
the fourth component "parent unit address", which size is defined by
'#address-cells' of the node pointed to by the interrupt-parent
component, is not used (=0)
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add missing address-cells 0 to GIC interrupt node to silence W=1
warning:
imx8mm.dtsi:1355.4-1358.29: Warning (interrupt_map): /soc@0/pcie@33800000:interrupt-map:
Missing property '#address-cells' in node /soc@0/interrupt-controller@38800000, using 0 as fallback
Value '0' is correct because:
1. GIC interrupt controller does not have children,
2. interrupt-map property (in PCI node) consists of five components and
the fourth component "parent unit address", which size is defined by
'#address-cells' of the node pointed to by the interrupt-parent
component, is not used (=0)
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add missing address-cells 0 to GIC interrupt node to silence W=1
warning:
imx8dxl-ss-hsio.dtsi:45.3-48.27: Warning (interrupt_map): /bus@5f000000/pcie@5f010000:interrupt-map:
Missing property '#address-cells' in node /interrupt-controller@51a00000, using 0 as fallback
Value '0' is correct because:
1. GIC interrupt controller does not have children,
2. interrupt-map property (in PCI node) consists of five components and
the fourth component "parent unit address", which size is defined by
'#address-cells' of the node pointed to by the interrupt-parent
component, is not used (=0)
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add missing address-cells 0 to GIC interrupt node to silence W=1
warning:
fsl-ls1046a.dtsi:334.5-346.26: Warning (interrupt_map): /soc/scfg@1570000/interrupt-controller@1ac:interrupt-map:
Missing property '#address-cells' in node /interrupt-controller@1400000, using 0 as fallback
Value '0' is correct because:
1. GIC interrupt controller does not have children,
2. interrupt-map property (in PCI node) consists of five components and
the fourth component "parent unit address", which size is defined by
'#address-cells' of the node pointed to by the interrupt-parent
component, is not used (=0)
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add missing address-cells 0 to GIC interrupt node to silence W=1
warning:
fsl-ls1043a.dtsi:330.5-342.26: Warning (interrupt_map): /soc/scfg@1570000/interrupt-controller@1ac:interrupt-map:
Missing property '#address-cells' in node /interrupt-controller@1400000, using 0 as fallback
Value '0' is correct because:
1. GIC interrupt controller does not have children,
2. interrupt-map property (in PCI node) consists of five components and
the fourth component "parent unit address", which size is defined by
'#address-cells' of the node pointed to by the interrupt-parent
component, is not used (=0)
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add missing address-cells 0 to GIC interrupt node to silence W=1
warning:
fsl-ls1012a.dtsi:548.4-551.32: Warning (interrupt_map): /soc/pcie@3400000:interrupt-map:
Missing property '#address-cells' in node /interrupt-controller@1400000, using 0 as fallback
Value '0' is correct because:
1. GIC interrupt controller does not have children,
2. interrupt-map property (in PCI node) consists of five components and
the fourth component "parent unit address", which size is defined by
'#address-cells' of the node pointed to by the interrupt-parent
component, is not used (=0)
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
xceiver-supply
Fix the can tranceivers to actually use the new phy description instead
of the regulator tweak.
Signed-off-by: Maud Spierings <maudspierings@gocontroll.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
board
Add support for TechNexion EDM-G-IMX8M-PLUS SOM and WB-EDM-G carrier board.
Key interfaces include:
- Gigabit Ethernet
- USB 3.0
- I2S, UART, SPI, I2C, PWM, GPIO
Signed-off-by: Richard Hu <richard.hu@technexion.com>
Signed-off-by: Ray Chang <ray.chang@technexion.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add the missing interconnect for the lcdif-hdmi.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add msi-map for pci-ep device.
Acked-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The ISP HDR stitching registers are clocked by the pixel clock, which is
gated by the MIPI_CSI2 power domain. Attempting to access those
registers with the clock off locks up the system. Fix this by adding the
pclk clock and the MIPI_CSI2 secondary power domain.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf
Florian Westpha says:
====================
netfilter pull request nf-25-09-10
First patch adds a lockdep annotation for a false-positive splat.
Last patch adds formal reviewer tag for Phil Sutter to MAINTAINERS.
Rest of the patches resolve spurious false negative results during set
lookups while another CPU is processing a transaction.
This has been broken at least since v4.18 when an unconditional
synchronize_rcu call was removed from the commit phase of nf_tables.
Quoting from Stefan Hanreichs original report:
It seems like we've found an issue with atomicity when reloading
nftables rulesets. Sometimes there is a small window where rules
containing sets do not seem to apply to incoming traffic, due to the set
apparently being empty for a short amount of time when flushing / adding
elements.
Exanple ruleset:
table ip filter {
set match {
type ipv4_addr
flags interval
elements = { 0.0.0.0-192.168.2.19, 192.168.2.21-255.255.255.255 }
}
chain pre {
type filter hook prerouting priority filter; policy accept;
ip saddr @match accept
counter comment "must never match"
}
}
Reproducer transaction:
while true:
nft -f -<<EOF
flush set ip filter match
create element ip filter match { \
0.0.0.0-192.168.2.19, 192.168.2.21-255.255.255.255 }
EOF
done
Then create traffic. to/from e.g. 192.168.2.1 to 192.168.3.10.
Once in a while the counter will increment even though the
'ip saddr @match' rule should have accepted the packet.
See individual patches for details.
Thanks to Stefan Hanreich for an initial description and reproducer for
this bug and to Pablo Neira Ayuso for reviewing earlier iterations of
the patchset.
* tag 'nf-25-09-10-v2' of https://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf:
MAINTAINERS: add Phil as netfilter reviewer
netfilter: nf_tables: restart set lookup on base_seq change
netfilter: nf_tables: make nft_set_do_lookup available unconditionally
netfilter: nf_tables: place base_seq in struct net
netfilter: nft_set_rbtree: continue traversal if element is inactive
netfilter: nft_set_pipapo: don't check genbit from packetpath lookups
netfilter: nft_set_bitmap: fix lockdep splat due to missing annotation
====================
Link: https://patch.msgid.link/20250910190308.13356-1-fw@strlen.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can
Marc Kleine-Budde says:
====================
pull-request: can 2025-09-10
The 1st patch is by Alex Tran and fixes the Documentation of the
struct bcm_msg_head.
Davide Caratti's patch enabled the VCAN driver as a module for the
Linux self tests.
Tetsuo Handa contributes 3 patches that fix various problems in the
CAN j1939 protocol.
Anssi Hannula's patch fixes a potential use-after-free in the
xilinx_can driver.
Geert Uytterhoeven's patch fixes the rcan_can's suspend to RAM on
R-Car Gen3 using PSCI.
* tag 'linux-can-fixes-for-6.17-20250910' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can:
can: rcar_can: rcar_can_resume(): fix s2ram with PSCI
can: xilinx_can: xcan_write_frame(): fix use-after-free of transmitted SKB
can: j1939: j1939_local_ecu_get(): undo increment when j1939_local_ecu_get() fails
can: j1939: j1939_sk_bind(): call j1939_priv_put() immediately when j1939_local_ecu_get() failed
can: j1939: implement NETDEV_UNREGISTER notification handler
selftests: can: enable CONFIG_CAN_VCAN as a module
docs: networking: can: change bcm_msg_head frames member to support flexible array
====================
Link: https://patch.msgid.link/20250910162907.948454-1-mkl@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2025-09-09 (igb, i40e)
For igb:
Tianyu Xu removes passing of, no longer needed, NAPI id to avoid NULL
pointer dereference on ethtool loopback testing.
Kohei Enju corrects reporting/testing of link state when interface is
down.
For i40e:
Michal Schmidt corrects value being passed to free_irq().
Jake sets hardware maximum frame size on probe to ensure
expected/consistent state.
* '1GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue:
i40e: fix Jumbo Frame support after iPXE boot
i40e: fix IRQ freeing in i40e_vsi_request_irq_msix error path
igb: fix link test skipping when interface is admin down
igb: Fix NULL pointer dereference in ethtool loopback test
====================
Link: https://patch.msgid.link/20250909203236.3603960-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Commit 3f490a74a8a1 ("clocksource/drivers/vf-pit: Rename the VF PIT to NXP
PIT") renames the config VF_PIT_TIMER to NXP_PIT_TIMER, but it misses
adjusting a reference to VF_PIT_TIMER in arch/arm/mach-imx/Kconfig.
Adjust the config reference to the new name.
Fixes: 3f490a74a8a1 ("clocksource/drivers/vf-pit: Rename the VF PIT to NXP PIT")
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@redhat.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The Ethernet PHY's reset GPIO should be specified in the node of the PHY
itself, instead of the MAC (`fec`). The latter is deprecated, and was an
i.MX-specific extension, incompatible with the new reset controller
subsystem.
Co-developed-by: Csaba Buday <buday.csaba@prolan.hu>
Signed-off-by: Csaba Buday <buday.csaba@prolan.hu>
Signed-off-by: Bence Csókás <csokas.bence@prolan.hu>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
To ensure successful builds when CONFIG_IMX_SCMI_CPU_DRV is not enabled,
this patch adds static inline stub implementations for the following
functions:
- scmi_imx_cpu_start()
- scmi_imx_cpu_started()
- scmi_imx_cpu_reset_vector_set()
These stubs return -EOPNOTSUPP to indicate that the functionality is not
supported in the current configuration. This avoids potential build or
link errors in code that conditionally calls these functions based on
feature availability.
Fixes: 1055faa5d660 ("firmware: imx: Add i.MX95 SCMI CPU driver")
Reviewed-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
To ensure successful builds when CONFIG_IMX_SCMI_LMM_DRV is not enabled,
this patch adds static inline stub implementations for the following
functions:
- scmi_imx_lmm_operation()
- scmi_imx_lmm_info()
- scmi_imx_lmm_reset_vector_set()
These stubs return -EOPNOTSUPP to indicate that the functionality is not
supported in the current configuration. This avoids potential build or
link errors in code that conditionally calls these functions based on
feature availability.
Fixes: 7242bbf418f0 ("firmware: imx: Add i.MX95 SCMI LMM driver")
Reviewed-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
To ensure successful builds when CONFIG_IMX_SCMI_MISC_DRV is not enabled,
this patch adds static inline stub implementations for the following
functions:
- scmi_imx_misc_ctrl_get()
- scmi_imx_misc_ctrl_set()
These stubs return -EOPNOTSUPP to indicate that the functionality is not
supported in the current configuration. This avoids potential build or
link errors in code that conditionally calls these functions based on
feature availability.
This patch also drops the changes in commit 540c830212ed ("firmware: imx:
remove duplicate scmi_imx_misc_ctrl_get()").
The original change aimed to simplify the handling of optional features by
removing conditional stubs. However, the use of conditional stubs is
necessary when CONFIG_IMX_SCMI_MISC_DRV is n, while consumer driver is
set to y.
This is not a matter of preserving legacy patterns, but rather to ensure
that there is no link error whether for module or built-in.
Fixes: 0b4f8a68b292 ("firmware: imx: Add i.MX95 MISC driver")
Reviewed-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The Netlink specs RST files are no longer generated inside the source
tree.
In other words, the path to mptcp_pm.rst has changed, and needs to be
updated to the new location.
Fixes: 1ce4da3dd99e ("docs: use parser_yaml extension to handle Netlink specs")
Reported-by: Kory Maincent <kory.maincent@bootlin.com>
Closes: https://lore.kernel.org/20250828185037.07873d04@kmaincent-XPS-13-7390
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/20250909-net-next-mptcp-pm-link-v1-1-0f1c4b8439c6@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
MicIn is connected to IN3_L. Add routing including the Mic Bias.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
fcnal-test.sh already includes lib.sh, use relevant helpers
instead of sleeping. Replace sleep after starting nettest
as a server with wait_local_port_listen.
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://patch.msgid.link/20250909223837.863217-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
MBa91xxCA (imx93-tqma9352-mba91xxca.dts) features a soldered,
non-pluggable USB attached WiFi module. lsusb says:
ID 1286:204e Marvell Semiconductor, Inc. Bluetooth and Wireless LAN Composite Device
Enable the corresponding driver.
To: Shawn Guo <shawnguo@kernel.org>
To: Fabio Estevam <festevam@gmail.com>
To: Sascha Hauer <s.hauer@pengutronix.de>
Cc: imx@lists.linux.dev
Cc: Pengutronix Kernel Team <kernel@pengutronix.de>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
imx53.dtsi has the following compatible entry:
compatible = "fsl,imx53-iomuxc-gpr", "syscon";
Document the "fsl,imx53-iomuxc-gpr" entry to fix the following
dt-schema warning:
failed to match any schema with compatible: ['fsl,imx53-iomuxc-gpr', 'syscon']
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Matthieu Baerts says:
====================
tools: ynl: fix errors reported by Ruff
When looking at the YNL code to add a new feature, my text editor
automatically executed 'ruff check', and found out at least one
interesting error: one variable was used while not being defined.
I then decided to fix this error, and all the other ones reported by
Ruff. After this series, 'ruff check' reports no more errors with
version 0.12.12.
====================
Link: https://patch.msgid.link/20250909-net-next-ynl-ruff-v1-0-238c2bccdd99@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
It is better to use 'not in' instead of 'not {element} in {collection}'
according to Ruff.
This is linked to Ruff error E713 [1]:
Testing membership with {element} not in {collection} is more readable.
Link: https://docs.astral.sh/ruff/rules/not-in-test/ [1]
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Reviewed-by: Donald Hunter <donald.hunter@gmail.com>
Reviewed-by: Asbjørn Sloth Tønnesen <ast@fiberby.net>
Link: https://patch.msgid.link/20250909-net-next-ynl-ruff-v1-8-238c2bccdd99@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
It is better to use the 'is' keyword instead of comparing to None
according to Ruff.
This is linked to Ruff error E711 [1]:
According to PEP 8, "Comparisons to singletons like None should always
be done with is or is not, never the equality operators."
Link: https://docs.astral.sh/ruff/rules/none-comparison/ [1]
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Reviewed-by: Donald Hunter <donald.hunter@gmail.com>
Reviewed-by: Asbjørn Sloth Tønnesen <ast@fiberby.net>
Link: https://patch.msgid.link/20250909-net-next-ynl-ruff-v1-7-238c2bccdd99@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
These semicolons are not required according to Ruff. Simply remove them.
This is linked to Ruff error E703 [1]:
A trailing semicolon is unnecessary and should be removed.
Link: https://docs.astral.sh/ruff/rules/useless-semicolon/ [1]
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Reviewed-by: Donald Hunter <donald.hunter@gmail.com>
Reviewed-by: Asbjørn Sloth Tønnesen <ast@fiberby.net>
Link: https://patch.msgid.link/20250909-net-next-ynl-ruff-v1-6-238c2bccdd99@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
These imports are not used according to Ruff, and can be safely removed.
This is linked to Ruff error F401 [1]:
Unused imports add a performance overhead at runtime, and risk
creating import cycles. They also increase the cognitive load of
reading the code.
There is one exception with 'YnlDocGenerator' which is added in __all__:
it is used by ynl_gen_rst.py.
Link: https://docs.astral.sh/ruff/rules/unused-import/ [1]
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Reviewed-by: Donald Hunter <donald.hunter@gmail.com>
Reviewed-by: Asbjørn Sloth Tønnesen <ast@fiberby.net>
Link: https://patch.msgid.link/20250909-net-next-ynl-ruff-v1-5-238c2bccdd99@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
