| Age | Commit message (Collapse) | Author |
|---|
|
To check if a request queue is for a rotational device, a double
negation is needed with the pattern "!blk_queue_nonrot(q)". Simplify
this with the introduction of the helper blk_queue_rot() which tests
if a requests queue limit has the BLK_FEAT_ROTATIONAL feature set.
All call sites of blk_queue_nonrot() are modified to use blk_queue_rot()
and blk_queue_nonrot() definition removed.
No functional changes.
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Nitesh Shetty <nj.shetty@samsung.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Unwrap the definition of BLK_FEAT_ATOMIC_WRITES and
renumber this feature to be sequential with BLK_FEAT_SKIP_TAGSET_QUIESCE.
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: John Garry <john.g.garry@oracle.com>
Reviewed-by: Nitesh Shetty <nj.shetty@samsung.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
This patch fixes the sparse warning issue in inode.c
by adding static to hfsplus_symlink_inode_operations
and hfsplus_special_inode_operations declarations.
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202601291957.bunRsD8R-lkp@intel.com/
Signed-off-by: Viacheslav Dubeyko <slava@dubeyko.com>
cc: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de>
cc: Yangtao Li <frank.li@vivo.com>
cc: linux-fsdevel@vger.kernel.org
Link: https://lore.kernel.org/r/20260129195442.594884-1-slava@dubeyko.com
Signed-off-by: Viacheslav Dubeyko <slava@dubeyko.com>
|
|
After a successful auxiliary_device_init(), aux_dev->dev.release
(xe_nvm_release_dev()) is responsible for the kfree(nvm). When
there is failure with auxiliary_device_add(), driver will call
auxiliary_device_uninit(), which call put_device(). So that the
.release callback will be triggered to free the memory associated
with the auxiliary_device.
Move the kfree(nvm) into the auxiliary_device_init() failure path
and remove the err goto path to fix below error.
"
[ 13.232905] ==================================================================
[ 13.232911] BUG: KASAN: double-free in xe_nvm_init+0x751/0xf10 [xe]
[ 13.233112] Free of addr ffff888120635000 by task systemd-udevd/273
[ 13.233120] CPU: 8 UID: 0 PID: 273 Comm: systemd-udevd Not tainted 6.19.0-rc2-lgci-xe-kernel+ #225 PREEMPT(voluntary)
...
[ 13.233125] Call Trace:
[ 13.233126] <TASK>
[ 13.233127] dump_stack_lvl+0x7f/0xc0
[ 13.233132] print_report+0xce/0x610
[ 13.233136] ? kasan_complete_mode_report_info+0x5d/0x1e0
[ 13.233139] ? xe_nvm_init+0x751/0xf10 [xe]
...
"
v2: drop err goto path. (Alexander)
Fixes: 7926ba2143d8 ("drm/xe: defer free of NVM auxiliary container to device release callback")
Reviewed-by: Nitin Gote <nitin.r.gote@intel.com>
Reviewed-by: Brian Nguyen <brian3.nguyen@intel.com>
Cc: Alexander Usyskin <alexander.usyskin@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Suggested-by: Brian Nguyen <brian3.nguyen@intel.com>
Signed-off-by: Shuicheng Lin <shuicheng.lin@intel.com>
Signed-off-by: Ashutosh Dixit <ashutosh.dixit@intel.com>
Link: https://patch.msgid.link/20260120183239.2966782-7-shuicheng.lin@intel.com
(cherry picked from commit a3187c0c2bbd947ffff97f90d077ac88f9c2a215)
Signed-off-by: Thomas Hellström <thomas.hellstrom@linux.intel.com>
|
|
Move nvm teardown to a devm-managed action registered from xe_nvm_init().
This ensures the auxiliary NVM device is deleted on probe failure and
device detach without requiring explicit calls from remove paths.
As part of this, drop xe_nvm_fini() from xe_device_remove() and from the
survivability sysfs teardown, and remove the public xe_nvm_fini() API from
the header.
This is to fix below warn message when there is probe failure after
xe_nvm_init(), then xe_device_probe() is called again:
"
[ 207.318152] sysfs: cannot create duplicate filename '/devices/pci0000:00/0000:00:01.0/0000:01:00.0/0000:02:01.0/0000:03:00.0/xe.nvm.768'
[ 207.318157] CPU: 5 UID: 0 PID: 10261 Comm: modprobe Tainted: G B W 6.19.0-rc2-lgci-xe-kernel+ #223 PREEMPT(voluntary)
[ 207.318160] Tainted: [B]=BAD_PAGE, [W]=WARN
[ 207.318161] Hardware name: ASUS System Product Name/PRIME Z790-P WIFI, BIOS 0812 02/24/2023
[ 207.318163] Call Trace:
[ 207.318163] <TASK>
[ 207.318165] dump_stack_lvl+0xa0/0xc0
[ 207.318170] dump_stack+0x10/0x20
[ 207.318171] sysfs_warn_dup+0xd5/0x110
[ 207.318175] sysfs_create_dir_ns+0x1f6/0x280
[ 207.318177] ? __pfx_sysfs_create_dir_ns+0x10/0x10
[ 207.318179] ? lock_acquire+0x1a4/0x2e0
[ 207.318182] ? __kasan_check_read+0x11/0x20
[ 207.318185] ? do_raw_spin_unlock+0x5c/0x240
[ 207.318187] kobject_add_internal+0x28d/0x8e0
[ 207.318189] kobject_add+0x11f/0x1f0
[ 207.318191] ? __pfx_kobject_add+0x10/0x10
[ 207.318193] ? lockdep_init_map_type+0x4b/0x230
[ 207.318195] ? get_device_parent.isra.0+0x43/0x4c0
[ 207.318197] ? kobject_get+0x55/0xf0
[ 207.318199] device_add+0x2d7/0x1500
[ 207.318201] ? __pfx_device_add+0x10/0x10
[ 207.318203] ? lockdep_init_map_type+0x4b/0x230
[ 207.318205] __auxiliary_device_add+0x99/0x140
[ 207.318208] xe_nvm_init+0x7a2/0xef0 [xe]
[ 207.318333] ? xe_devcoredump_init+0x80/0x110 [xe]
[ 207.318452] ? __devm_add_action+0x82/0xc0
[ 207.318454] ? fs_reclaim_release+0xc0/0x110
[ 207.318457] xe_device_probe+0x17dd/0x2c40 [xe]
[ 207.318574] ? __pfx___drm_dev_dbg+0x10/0x10
[ 207.318576] ? add_dr+0x180/0x220
[ 207.318579] ? __pfx___drmm_mutex_release+0x10/0x10
[ 207.318582] ? __pfx_xe_device_probe+0x10/0x10 [xe]
[ 207.318697] ? xe_pm_init_early+0x33a/0x410 [xe]
[ 207.318850] xe_pci_probe+0x936/0x1250 [xe]
[ 207.318999] ? lock_acquire+0x1a4/0x2e0
[ 207.319003] ? __pfx_xe_pci_probe+0x10/0x10 [xe]
[ 207.319151] local_pci_probe+0xe6/0x1a0
[ 207.319154] pci_device_probe+0x523/0x840
[ 207.319157] ? __pfx_pci_device_probe+0x10/0x10
[ 207.319159] ? sysfs_do_create_link_sd.isra.0+0x8c/0x110
[ 207.319162] ? sysfs_create_link+0x48/0xc0
...
"
Fixes: c28bfb107dac ("drm/xe/nvm: add on-die non-volatile memory device")
Reviewed-by: Alexander Usyskin <alexander.usyskin@intel.com>
Reviewed-by: Brian Nguyen <brian3.nguyen@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Riana Tauro <riana.tauro@intel.com>
Signed-off-by: Shuicheng Lin <shuicheng.lin@intel.com>
Signed-off-by: Ashutosh Dixit <ashutosh.dixit@intel.com>
Link: https://patch.msgid.link/20260120183239.2966782-6-shuicheng.lin@intel.com
(cherry picked from commit 11035eab1b7d88daa7904440046e64d3810b1ca1)
Signed-off-by: Thomas Hellström <thomas.hellstrom@linux.intel.com>
|
|
Add support of Foresee F35SQB002G spinand flash
Signed-off-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@iopsys.eu>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
Extend the support for the W35N chip family by supporting the ODTR bus
interface. The chip is capable to run in this mode, which brings a
significant performance improvement.
1S-8S-8S:
# flash_speed /dev/mtd0 -c1 -d
eraseblock write speed is 7529 KiB/s
eraseblock read speed is 15058 KiB/s
8D-8D-8D:
# flash_speed /dev/mtd0 -c1 -d
eraseblock write speed is 9481 KiB/s
eraseblock read speed is 23272 KiB/s
This is +55% read speed and +26% write speed with the same hardware.
Tests have been conducted with a TI AM62A7 using the Cadence quad SPI
controller.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
Create a new bus interface named ODTR for "octal DTR", which matches the
following pattern: 8D-8D-8D.
Add octal DTR support for all the existing core operations. Add a second
set of templates for this bus interface.
Give the possibility for drivers to register their read, write and
update cache variants as well as their vendor specific operations.
Check the SPI controller driver supports all the octal DTR commands that
we might need before switching to the ODTR bus interface.
Make the switch by calling ->configure_chip() with the ODTR
parameter. Fallback in case this step fails.
If someone ever attempts to suspend a chip in octal DTR mode, there are
changes that it will loose its configuration at resume. Prevent any
problem by explicitly switching back to SSDR while suspending. Note:
there is a limitation in the current approach, page I/Os are not
available as the dirmaps will be created for the ODTR bus interface if
that option is supported and not switched back to SSDR during
suspend. Switching them is possible but would be costly and would not
bring anything as right after resuming we will switch again to ODTR. In
case this capability is used for debug, developpers should mind to
destroy and recreate suitable direct mappings.
Finally, as a side effect, we increase the buffer for reading IDs to
6. No device at this point returns 6 bytes, but we support 5 bytes IDs,
which means in octal DTR mode we have no other choice than reading an
even number of bytes, hence 6.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
Both Macronix and Winbond have chip specific operations which are SSDR
only. Trying to use them in an ODTR setup will fail and doing this is a
pure software bug. Warn explicitly in this case.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
The chip configuration hook is the one responsible to actually switch
the switch between bus interfaces. It is natural to give it the bus
interface we expect with a new parameter. For now the only value we can
give is SSDR, but this is subject to change in the future, so add a bit
of extra logic in the implementations of this callback to make sure
both the core and the chip driver are aligned on the request.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
For now all drivers provide SSDR variants only. When we add support for
ODTR modes, there will be a need to differentiate the type of variant we
target as well as the need to check if we support one or the other type
of operations.
Pass this parameter to lower level helpers, which for now is unused, in
order to simplify the patch introducing ODTR support.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
Create a bus interface enumeration, currently only containing the
one we support: SSDR, for single SDR, so any operation whose command is
sent over a single data line in SDR mode, ie. any operation matching
1S-XX-XX.
The main spinand_device structure gets a new parameter to store this
enumeration, for now unused. Of course it is set to SSDR during the SSDR
templates initialization to further clarify the state we are in at the
moment.
This member is subject to be used to know in which bus configuration we
and be updated by the core when we switch to faster mode(s).
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
Writing the quad enable bit in one helper and doing the chip
configuration in another does not make much sense from a bus interface
setup point of view.
Instead, let's create a broader helper which is going to be in charge of
all the bus configuration steps at once. This will specifically allow to
transition to octal DDR mode, and even fallback to quad (if suppoorted)
or single mode otherwise.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
When we will change the bus interface, the action that actually performs
the transition is the IO mode register write. This means after the IO
mode register write, we should use the new bus interface. But the
->configure_chip() hook itself is not responsible of making this change
official, it is the caller that must act according to the return value.
Reorganize this helper to first configure the dummy cycles before
possibly switching to another bus interface.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
Suffix the macro name with *_REG to align with the rest of the driver.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
Add a missing new line in the middle of the driver.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
Provide the Winbond W35N specific "write VCR register" operation to let
the core verify it is supported by the controller before using it.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
Provide the Winbond W25N specific "select target" operation to let the
core verify it is supported by the controller before using it.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
Provide the Macronix specific "read ECC status register" operation so
that the core can verify if it is supported by the controller before
using it.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
It is probably safe to expect that all SPI controller drivers will ever
support all the most basic SPI NAND operations, such as write enable,
register reads, page program, block erases, etc. However, what about
vendor specific operations? So far nobody complained about it, but as we
are about to introduce octal DTR support, and as none of the SPI NAND
instruction set is defined in any standard, we must remain careful about
these extra operations.
One way to make sure we do not blindly get ourselves in strange
situations with vendor commands failing silently is to make the check
once for all, while probing the chip. However at this stage we have no
such list, so let's add the necessary infrastructure to allow:
- registering vendor operations,
- checking they are actually supported when appropriate.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
Winbond W35N* chips require a vendor specific operation to write their
VCR register (a configuration register, typically used for tuning the
number of dummy cycles and switching to a different bus
interface). Instead of defining this op only in the function that needs
it, hiding it from the core, make it a proper define like all other
spi-mem operations, and implement the necessary spinand_fill_*_op()
helper to make the SPINAND_OP() macro work. This way we can use it from
any function without any extra handling outside of this helper when we
will convert the core to support octal DDR busses.
Reviewed-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
Winbond W25N* chips require a vendor specific operation to select the
target. Instead of defining this op only in the function that
needs it, hiding it from the core, make it a proper define like all
other spi-mem operations, and implement the necessary
spinand_fill_*_op() helper to make the SPINAND_OP() macro work. This way
we can use it from any function without any extra handling outside of
this helper when we will convert the core to support octal DDR busses.
Reviewed-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
Macronix chips require a vendor specific operation to read the ECC
status register. Instead of defining this op only in the function that
needs it, hiding it from the core, make it a proper define like all
other spi-mem operations, and implement the necessary
spinand_fill_*_op() helper to make the SPINAND_OP() macro work. This way
we can use it from any function without any extra handling outside of
this helper when we will convert the core to support octal DDR busses.
Reviewed-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
Create a SPINAND_OP() macro to which we give the name of the operation
we want. This macro retrieves the correct operation template based on
the current bus interface (currently only single SDR, will soon be
extended to octal DTR) and fills it with the usual parameters.
This macro makes the transition from calling directly the low-level
macros into using the (bus interface dependent) templates very smooth.
Use it in all places that can be trivially converted. At this stage
there is no functional change expected, until octal DTR support gets
added.
Reviewed-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
Currently, the SPI NAND core implementation directly calls macros to get
the various operations in shape. These macros are specific to the bus
interface, currently only supporting the single SDR interface (any
command following the 1S-XX-XX pattern).
Introducing support for other bus interfaces (such as octal DTR) would
mean that every user of these macros should become aware of the current
bus interface and act accordingly, picking up and adapting to the
current configuration. This would add quite a bit of boilerplate, be
repetitive as well as error prone in case we miss one occurrence.
Instead, let's create a table with all SPI NAND memory operations that
are currently supported. We initialize them with the same single SDR _OP
macros as before. This opens the possibility for users of the individual
macros to make use of these templates instead. This way, when we will add
another bus interface, we can just switch to another set of templates
and all users will magically fill in their spi_mem_op structures with
the correct ops.
The existing read, write and update cache variants are also moved in
this template array, which is barely noticeable by callers as we also
add a structure member pointing to it.
Reviewed-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
In order to introduce templates for all operations and not only for page
helpers (in order to introduce octal DDR support), decouple the WR_EN
and WR_DIS operations into two separate macros.
Adapt the callers accordingly.
There is no functional change.
Reviewed-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
Replace -ENOTSUPP with -EOPNOTSUPP which is as relevant in this case but
is standard.
Reviewed-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
SPI NAND command values are directly included in the macros defining the
ops. These are stale definitions, they are unused so drop them.
Reviewed-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
The update cache variant is mandatory, both read and write versions are
being checked, but not this one. All chip drivers seem to implement this
variant, so there should be no breakage.
Reviewed-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
The @data buffer is 5 bytes, not 4, it has been extended for the need of
devices with an extra ID bytes.
Fixes: 34a956739d29 ("mtd: spinand: Add support for 5-byte IDs")
Reviewed-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
In octal DTR mode addresses may either be long enough to cover at least
two bytes (in which case the existing macro works), or otherwise for
single byte addresses, the byte must also be duplicated and sent twice:
on each front of the clock.
Create a macro for this common case.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
spi: Octal DTR support
This series adds support for 8D-8D-8D in SPI NAND, which can already be
leveraged without any SPI changes as controllers already have this
support for some SPI NOR devices.
Among the few spi-mem patches, they are needed for building the SPI NAND
changes (especially the ODTR introduction at the end) and therefore an
immutable tag will be needed for merging in the MTD tree (unless all the
series goes through MTD directly ofc).
|
|
Place the ofparts before RedBoot partitions in the OF probe
path: this makes it possible to override any existing
RedBoot partitions with fixed-partitions which may be necessary,
such as when you need to repartition the flash from Linux'
point of view but not necessary from the bootloaders point
of view.
This happens when a device such as Raidsonic IB-4220-B has
three partitions named "Kern", "Ramdisk" and "Application"
that we want to merge into one for more efficient use
of the flash memory in OpenWrt.
Signed-off-by: Linus Walleij <linusw@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
Convert Macronix Raw NAND Controller Device Tree binding to DT Schema.
Signed-off-by: Akhila YS <akhilayalmati@gmail.com>
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
of_get_child_by_name() returns a node pointer with refcount incremented,
which must be released with of_node_put() when done. However, in
parse_fixed_partitions(), when dedicated is true (i.e., a "partitions"
subnode was found), the ofpart_node obtained from of_get_child_by_name()
is never released on any code path.
Add of_node_put(ofpart_node) calls on all exit paths when dedicated is
true to fix the reference count leak.
This bug was detected by our static analysis tool.
Fixes: 562b4e91d3b2 ("mtd: parsers: ofpart: fix parsing subpartitions")
Signed-off-by: Weigang He <geoffreyhe2@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
Convert STMicroelectronics SPEAr600 Serial Memory Interface (SMI)
Controller binding to YAML format.
Signed-off-by: Akhila YS <akhilayalmati@gmail.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm
Pull misc fixes from Andrew Morton:
"16 hotfixes. 9 are cc:stable, 12 are for MM.
There's a patch series from Pratyush Yadav which fixes a few things in
the new-in-6.19 LUO memfd code.
Plus the usual shower of singletons - please see the changelogs for
details"
* tag 'mm-hotfixes-stable-2026-01-29-09-41' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm:
vmcoreinfo: make hwerr_data visible for debugging
mm/zone_device: reinitialize large zone device private folios
mm/mm_init: don't cond_resched() in deferred_init_memmap_chunk() if called from deferred_grow_zone()
mm/kfence: randomize the freelist on initialization
kho: kho_preserve_vmalloc(): don't return 0 when ENOMEM
kho: init alloc tags when restoring pages from reserved memory
mm: memfd_luo: restore and free memfd_luo_ser on failure
mm: memfd_luo: use memfd_alloc_file() instead of shmem_file_setup()
memfd: export alloc_file()
flex_proportions: make fprop_new_period() hardirq safe
mailmap: add entry for Viacheslav Bocharov
mm/memory-failure: teach kill_accessing_process to accept hugetlb tail page pfn
mm/memory-failure: fix missing ->mf_stats count in hugetlb poison
mm, swap: restore swap_space attr aviod kernel panic
mm/kasan: fix KASAN poisoning in vrealloc()
mm/shmem, swap: fix race of truncate and swap entry split
|
|
While reworking the LSM initialization code the
/proc/sys/vm/mmap_min_addr handler was inadvertently caught up in the
change and the procfs entry wasn't setup when CONFIG_SECURITY was not
selected at kernel build time. This patch restores the previous behavior
and ensures that the procfs entry is setup regardless of the
CONFIG_SECURITY state.
Future work will improve upon this, likely by moving the procfs handler
into the mm subsystem, but this patch should resolve the immediate
regression.
Fixes: 4ab5efcc2829 ("lsm: consolidate all of the LSM framework initcalls")
Reported-by: Lorenzo Stoakes <lorenzo.stoakes@oracle.com>
Reviewed-by: Lorenzo Stoakes <lorenzo.stoakes@oracle.com>
Tested-by: Lorenzo Stoakes <lorenzo.stoakes@oracle.com>
Reviewed-by: Kees Cook <kees@kernel.org>
Signed-off-by: Paul Moore <paul@paul-moore.com>
|
|
Add QCA_CAP_HFP_HW_OFFLOAD capability flag to WCN6855 and WCN7850
device data structures to enable Hands-Free Profile (HFP) hardware
offload support on these Qualcomm Bluetooth chipsets.
Signed-off-by: Mengshi Wu <mengshi.wu@oss.qualcomm.com>
Acked-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Replace SoC-specific check with capability-based approach for HFP
hardware offload configuration. Add QCA_CAP_HFP_HW_OFFLOAD capability
flag and support_hfp_hw_offload field to qca_serdev structure. Add
QCA_CAP_HFP_HW_OFFLOAD capability flag to QCA2066 device data
structures.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Mengshi Wu <mengshi.wu@oss.qualcomm.com>
Acked-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Add USB ID 7392:e611 for Edimax EW-7611UXB which is RTL8851BU-based
Wi-Fi + Bluetooth adapter.
The information in /sys/kernel/debug/usb/devices about the Bluetooth
device is listed as the below:
T: Bus=03 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 6 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=7392 ProdID=e611 Rev= 0.00
S: Manufacturer=Realtek
S: Product=802.11ax WLAN Adapter
S: SerialNumber=00e04c000001
C:* #Ifs= 3 Cfg#= 1 Atr=e0 MxPwr=500mA
A: FirstIf#= 0 IfCount= 2 Cls=e0(wlcon) Sub=01 Prot=01
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms
I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms
I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms
I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms
I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms
I: If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 63 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 63 Ivl=1ms
I:* If#= 2 Alt= 0 #EPs= 8 Cls=ff(vend.) Sub=ff Prot=ff Driver=rtw89_8851bu_git
E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=06(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=07(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=09(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=0a(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=0b(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=0c(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
Cc: stable@vger.kernel.org # 6.6.x
Signed-off-by: Zenm Chen <zenmchen@gmail.com>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
This attempts to proper track outstanding request by using struct ida
and allocating from it in l2cap_get_ident using ida_alloc_range which
would reuse ids as they are free, then upon completion release
the id using ida_free.
This fixes the qualification test case L2CAP/COS/CED/BI-29-C which
attempts to check if the host stack is able to work after 256 attempts
to connect which requires Ident field to use the full range of possible
values in order to pass the test.
Link: https://github.com/bluez/bluez/issues/1829
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
|
|
Fix memory leak in set_ssp_complete() where mgmt_pending_cmd structures
are not freed after being removed from the pending list.
Commit 302a1f674c00 ("Bluetooth: MGMT: Fix possible UAFs") replaced
mgmt_pending_foreach() calls with individual command handling but missed
adding mgmt_pending_free() calls in both error and success paths of
set_ssp_complete(). Other completion functions like set_le_complete()
were fixed correctly in the same commit.
This causes a memory leak of the mgmt_pending_cmd structure and its
associated parameter data for each SSP command that completes.
Add the missing mgmt_pending_free(cmd) calls in both code paths to fix
the memory leak. Also fix the same issue in set_advertising_complete().
Fixes: 302a1f674c00 ("Bluetooth: MGMT: Fix possible UAFs")
Signed-off-by: Jianpeng Chang <jianpeng.chang.cn@windriver.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
hci_uart_set_proto() sets HCI_UART_PROTO_INIT before calling
hci_uart_register_dev(), which calls proto->open() to initialize
hu->priv. However, if a TTY write wakeup occurs during this window,
hci_uart_tx_wakeup() may schedule write_work before hu->priv is
initialized, leading to a NULL pointer dereference in
hci_uart_write_work() when proto->dequeue() accesses hu->priv.
The race condition is:
CPU0 CPU1
---- ----
hci_uart_set_proto()
set_bit(HCI_UART_PROTO_INIT)
hci_uart_register_dev()
tty write wakeup
hci_uart_tty_wakeup()
hci_uart_tx_wakeup()
schedule_work(&hu->write_work)
proto->open(hu)
// initializes hu->priv
hci_uart_write_work()
hci_uart_dequeue()
proto->dequeue(hu)
// accesses hu->priv (NULL!)
Fix this by moving set_bit(HCI_UART_PROTO_INIT) after proto->open()
succeeds, ensuring hu->priv is initialized before any work can be
scheduled.
Fixes: 5df5dafc171b ("Bluetooth: hci_uart: Fix another race during initialization")
Link: https://lore.kernel.org/linux-bluetooth/6969764f.170a0220.2b9fc4.35a7@mx.google.com/
Signed-off-by: Jia-Hong Su <s11242586@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
The USB device ID 0x13d3/0x3618 is listed twice in the device table.
Remove the duplicate entry and keep the one under the correct
"Realtek 8852BT/8852BE-VT Bluetooth devices" section.
Signed-off-by: Linmao Li <lilinmao@kylinos.cn>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Add USB device ID 0x2c0a:0x8761 to the btusb driver fo the Realtek
RTL8761BU Bluetooth adapter.
Reference:
https://www.startech.com/en-us/networking-io/av53c1-usb-bluetooth
Signed-off-by: Jacopo Scannella <code@charlie.cat>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
The functions are already disabled if CONFIG_PM or CONFIG_PM_SLEEP are
disabled through the use of SET_SYSTEM_SLEEP_PM_OPS() and
SET_RUNTIME_PM_OPS().
This increases build coverage and allows to drop a few #ifdef's.
Signed-off-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
The functions are already disabled through the use of pm_ptr() when
CONFIG_PM is disabled, and will be removed from the final linked code
as not needed.
This increases build coverage and allows to drop an #ifdef.
Signed-off-by: Bastien Nocera <hadess@hadess.net>
Reviewed-by: Neeraj Sanjay Kale <neeraj.sanjaykale@nxp.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Add VID:PID 13d3:3612 to the quirks_table.
This ID pair is found in the Realtek RTL8852CE PCIe module
in an ASUS TUF A14 2025 (FA401KM) laptop.
Tested on aforementioned laptop.
The device info from /sys/kernel/debug/usb/devices is listed as below.
T: Bus=03 Lev=01 Prnt=01 Port=04 Cnt=01 Dev#= 2 Spd=12 MxCh= 0
D: Ver= 1.00 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=13d3 ProdID=3612 Rev= 0.00
S: Manufacturer=Realtek
S: Product=Bluetooth Radio
S: SerialNumber=00e04c000001
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms
I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms
I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms
I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms
I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms
I: If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 63 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 63 Ivl=1ms
Signed-off-by: Shell Chen <w27@sorz.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
The kfree_skb() function internally checks if the skb is NULL,
so an explicit check before calling it is redundant and can be removed.
Signed-off-by: Chen Ni <nichen@iscas.ac.cn>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
