1 files changed, 0 insertions, 98 deletions
diff --git a/Documentation/devicetree/bindings/phy/ti-phy.txt b/Documentation/devicetree/bindings/phy/ti-phy.txt
deleted file mode 100644
index 7c7936b89f2c..000000000000
--- a/Documentation/devicetree/bindings/phy/ti-phy.txt
+++ /dev/null
@@ -1,98 +0,0 @@
-TI PHY: DT DOCUMENTATION FOR PHYs in TI PLATFORMs
-
-OMAP CONTROL PHY
-
-Required properties:
- - compatible: Should be one of
- "ti,control-phy-otghs" - if it has otghs_control mailbox register as on OMAP4.
- "ti,control-phy-usb2" - if it has Power down bit in control_dev_conf register
-                        e.g. USB2_PHY on OMAP5.
- "ti,control-phy-pipe3" - if it has DPLL and individual Rx & Tx power control
-                        e.g. USB3 PHY and SATA PHY on OMAP5.
- "ti,control-phy-pcie" - for pcie to support external clock for pcie and to
-			set PCS delay value.
-			e.g. PCIE PHY in DRA7x
- "ti,control-phy-usb2-dra7" - if it has power down register like USB2 PHY on
-                        DRA7 platform.
- "ti,control-phy-usb2-am437" - if it has power down register like USB2 PHY on
-                        AM437 platform.
- - reg : register ranges as listed in the reg-names property
- - reg-names: "otghs_control" for control-phy-otghs
-	      "power", "pcie_pcs" and "control_sma" for control-phy-pcie
-	      "power" for all other types
-
-omap_control_usb: omap-control-usb@4a002300 {
-        compatible = "ti,control-phy-otghs";
-        reg = <0x4a00233c 0x4>;
-        reg-names = "otghs_control";
-};
-
-TI PIPE3 PHY
-
-Required properties:
- - compatible: Should be "ti,phy-usb3", "ti,phy-pipe3-sata" or
-   "ti,phy-pipe3-pcie. "ti,omap-usb3" is deprecated.
- - reg : Address and length of the register set for the device.
- - reg-names: The names of the register addresses corresponding to the registers
-   filled in "reg".
- - #phy-cells: determine the number of cells that should be given in the
-   phandle while referencing this phy.
- - clocks: a list of phandles and clock-specifier pairs, one for each entry in
-   clock-names.
- - clock-names: should include:
-   * "wkupclk" - wakeup clock.
-   * "sysclk" - system clock.
-   * "refclk" - reference clock.
-   * "dpll_ref" - external dpll ref clk
-   * "dpll_ref_m2" - external dpll ref clk
-   * "phy-div" - divider for apll
-   * "div-clk" - apll clock
-
-Optional properties:
- - id: If there are multiple instance of the same type, in order to
-   differentiate between each instance "id" can be used (e.g., multi-lane PCIe
-   PHY). If "id" is not provided, it is set to default value of '1'.
- - syscon-pllreset: Handle to system control region that contains the
-   CTRL_CORE_SMA_SW_0 register and register offset to the CTRL_CORE_SMA_SW_0
-   register that contains the SATA_PLL_SOFT_RESET bit. Only valid for sata_phy.
- - syscon-pcs : phandle/offset pair. Phandle to the system control module and the
-   register offset to write the PCS delay value.
-
-Deprecated properties:
- - ctrl-module : phandle of the control module used by PHY driver to power on
-   the PHY.
-
-Recommended properties:
- - syscon-phy-power : phandle/offset pair. Phandle to the system control
-   module and the register offset to power on/off the PHY.
-
-This is usually a subnode of ocp2scp to which it is connected.
-
-usb3phy@4a084400 {
-	compatible = "ti,phy-usb3";
-	reg = <0x4a084400 0x80>,
-	      <0x4a084800 0x64>,
-	      <0x4a084c00 0x40>;
-	reg-names = "phy_rx", "phy_tx", "pll_ctrl";
-	ctrl-module = <&omap_control_usb>;
-	#phy-cells = <0>;
-	clocks = <&usb_phy_cm_clk32k>,
-		 <&sys_clkin>,
-		 <&usb_otg_ss_refclk960m>;
-	clock-names =	"wkupclk",
-			"sysclk",
-			"refclk";
-};
-
-sata_phy: phy@4a096000 {
-	compatible = "ti,phy-pipe3-sata";
-	reg = <0x4A096000 0x80>, /* phy_rx */
-	      <0x4A096400 0x64>, /* phy_tx */
-	      <0x4A096800 0x40>; /* pll_ctrl */
-	reg-names = "phy_rx", "phy_tx", "pll_ctrl";
-	ctrl-module = <&omap_control_sata>;
-	clocks = <&sys_clkin1>, <&sata_ref_clk>;
-	clock-names = "sysclk", "refclk";
-	syscon-pllreset = <&scm_conf 0x3fc>;
-	#phy-cells = <0>;
-};